The EGR valve position sensor is mounted on the EGR valve and is used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0405 | Exhaust Gas Recirculation Sensor "A" Circuit Low | EGR valve position sensor output voltage is below 0.1 V for more than 5 seconds (1 trip detection logic). | ·
Open or short in EGR valve position sensor circuit ·
EGR valve position sensor ·
ECM |
- | DTC stored |
| P0406 | Exhaust Gas Recirculation Sensor "A" Circuit High | EGR valve position sensor output voltage is more than 4.9 V for higher than 5 seconds (1 trip detection logic). | ·
Open or short in EGR valve position sensor circuit ·
EGR valve position sensor ·
ECM |
- | DTC stored |
| DTC Detection Drive Pattern | Ignition switch to ON for 5 seconds |
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.
After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>REGISTRATION) and initialization (See page Engine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>INITIALIZATION).
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| *a | Front view of wire harness connector
(to EGR Valve Position Sensor) |
Disconnect the EGR valve position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C56-1 (VC) - C56-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
Reconnect the electric vacuum regulating valve assembly connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the EGR valve position sensor.
Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EGR VALVE(w/o DPF)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the EGR valve position sensor connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C56-1 (VC) - C22-18 (VC) | Always | Below 1 Ω |
| C56-3 (EGLS) - C23-33 (EGLS) | Always | Below 1 Ω |
| C56-2 (E2) - C22-28 (E2) | Always | Below 1 Ω |
| C56-1 (VC) or C22-18 (VC) - Body ground | Always | 10 kΩ or higher |
| C56-3 (EGLS) or C23-33 (EGLS) - Body ground | Always | 10 kΩ or higher |
Reconnect the electric vacuum regulating valve assembly connector.
Reconnect the ECM connector.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the electric EGR control valve assembly.
Click hereEngine / Hybrid System>2KD-FTV EMISSION CONTROL>EGR VALVE(w/o DPF)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Clear the DTCs.
Click hereEngine / Hybrid System>2KD-FTV ENGINE CONTROL>ECD SYSTEM(w/o EGR Cooler)>DTC CHECK / CLEAR
Turn the ignition switch to ON for 5 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Confirm that the DTC is not output again.
| Proceed to |
|---|
| NEXT |
NEXT