Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) C

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  P0093  Fuel System Leak Detected - Large Leak  P029D  Cylinder 1 - Injector Leaking  P02A1  Cylinder 2 - Injector Leaking  P02A5  Cylinder 3 - Injector Leaking  P02A9  Cylinder 4 - Injector Leaking  


DESCRIPTION

A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>SYSTEM DESCRIPTION).

HINT:
·

If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P0093, P029D, P02A1, P02A5 and P02A9.

·

If P0093, P029D, P02A1, P02A5 and P02A9 are present, refer to "Diagnostic Trouble Code (DTC) Table for Common Rail System" (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>SYSTEM DESCRIPTION).



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0093 Fuel System Leak Detected - Large Leak Fuel pressure drop before and after fuel injection is larger than the threshold a certain number of times (0.2 seconds or more).
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in injector driver circuit (P062D stored simultaneously)

·

Open or short in injector circuit

·

Injector driver (P062D stored simultaneously)

·

ECM


Comes on DTC stored
P029D Cylinder 1 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in injector driver circuit (P062D stored simultaneously)

·

Open or short in injector circuit

·

Injector driver (P062D stored simultaneously)

·

ECM


Comes on DTC stored
P02A1 Cylinder 2 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in injector driver circuit (P062D stored simultaneously)

·

Open or short in injector circuit

·

Injector driver (P062D stored simultaneously)

·

ECM


Comes on DTC stored
P02A5 Cylinder 3 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in injector driver circuit (P062D stored simultaneously)

·

Open or short in injector circuit

·

Injector driver (P062D stored simultaneously)

·

ECM


Comes on DTC stored
P02A9 Cylinder 4 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Suction control valve

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element sub-assembly

·

Open or short in injector driver circuit (P062D stored simultaneously)

·

Open or short in injector circuit

·

Injector driver (P062D stored simultaneously)

·

ECM


Comes on DTC stored

Related Data List
DTC No. Data List
P0093
P029D
P02A1
P02A5
P02A9
·

Fuel Press

·

Target Common Rail Pressure

·

i-ART Learning Status History #1 to #4

·

Injector Leaking Count #1 to #4



HINT:

When DTC P0093, P029D, P02A1, P02A5 and P02A9 are set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Press.


Reference:
Engine Speed Fuel Press
Idling Approximately 30000 to 50000 kPa
3000 rpm (No engine load) Approximately 60000 to 95000 kPa


CONFIRMATION DRIVING PATTERN

P0093, P029D, P02A1, P02A5, P02A9
DTC Detection Drive Pattern After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)
Repeat procedures (*A) and (*B) 5 times.

MONITOR DESCRIPTION

P0093, P029D, P02A1, P02A5, P02A9 (Fuel leaks in high-pressure areas):

This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is excessively large when injecting fuel.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping. The ECM adjusts the suction control valve opening angle to obtain the target internal fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, fuel supply pump assembly operation is limited. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


MONITOR STRATEGY

Required sensors Fuel pressure sensor
Frequency of operation Continuous
Duration 1 second
MIL operation 1 driving cycle

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the fuel supply pump assembly, injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR ANY OTHER DTCS OUTPUT AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)

NG

REPAIR FUEL LEAK POINT

2.CHECK FOR ANY OTHER DTCS OUTPUT AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

d.

Read the DTCs and freeze frame data.

Result:
Result Proceed to
P0093 and P13A1, P13A2, P13A3, P13A6, P13A7, P13A8, P13AB, P13AC, P13AD, P13B1, P13B2, P13B3, P13C3, P13C8, P13CD and/or P13D3 are output C
P0093 and P0335, P0339 and/or P0340 are output B
Except above A




A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

GO TO CRANKSHAFT POSITION SENSOR "A" CIRCUIT

C

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result:
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B




A

4.ADD FLUID

B

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
4.ADD FLUID
a.

Add fuel.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.
A223284

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element sub-assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the ignition switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

g.

Start the engine. (*A)


h.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak. (*B)

Powertrain > Engine > Active Test
Tester Display
Test the Fuel Leak
50004 61 90

i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. (*C)


j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. (*D)

A192848E22
0.177,1.313 1.542,1.531 1.365,0.219 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.542,1.927 3.354,2.094 0.813,0.167 10 false 10 seconds 3.156,0.688 3.969,0.854 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.406 0.594,0.167 10 false 1st time 3.896,0.24 4.49,0.406 0.594,0.167 10 false 2nd time 5.188,0.24 5.781,0.406 0.594,0.167 10 false 5th time 5.99,1.885 6.802,2.052 0.813,0.167 10 false 3 minutes


k.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

l.

Read Current DTCs.

i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



m.

Repeat steps (*A) to (*D).


n.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

o.

Start the engine and warm it up.


p.

Confirm that the shift lever is in neutral and securely apply the parking brake.


q.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*E)


r.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*F)


s.

Repeat procedures (*E) and (*F) 5 times.

A220593E08
1.656,1.844 2.042,2.021 0.385,0.177 10 false 5000 1.51,0.583 2.01,0.76 0.5,0.177 10 false 160000 5.135,2.125 5.771,2.302 0.635,0.177 10 false 3000 rpm 1.865,2.563 1.99,2.74 0.125,0.177 10 false 0 1.854,1.24 1.979,1.417 0.125,0.177 10 false 0 0.073,0.823 1.021,1.073 0.948,0.25 10 false Fuel Pressure 0.083,2.167 1.01,2.438 0.927,0.271 10 false Engine Speed 0.083,3.458 1.25,3.656 1.167,0.198 10 false Accelerator Pedal 0.948,3.083 2.115,3.281 1.167,0.198 10 false Fully Depressed 1.021,3.719 2,3.917 0.979,0.198 10 false Fully Released 2.875,4.24 3.573,4.427 0.698,0.188 10 false 5 seconds 6.448,4.135 6.854,4.323 0.406,0.188 10 false Time 3.104,2.958 3.729,3.198 0.625,0.24 10 false Step (*E) 6.208,2.948 6.813,3.188 0.604,0.24 10 false Step (*E) 4.75,2.958 5.375,3.198 0.625,0.24 10 false Step (*F) 2.104,0.573 2.375,0.76 0.271,0.188 10 false kPa 2.073,1.771 2.385,1.938 0.313,0.167 10 false rpm


t.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

u.

Read Current DTCs.

Result:
Result Proceed to
DTC is output A
No DTC is output B




A

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)

B

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VAL #1 TO #4)
a.

Read the value of Injection Feedback Val #1 to #4 in the freeze frame data recorded in Procedure 2.

Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data B
Except above A


HINT:

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.




A

7.READ VALUE USING GTS (FUEL PRESS)

B

10.CHECK FREEZE FRAME DATA
7.READ VALUE USING GTS (FUEL PRESS)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Press.

Powertrain > Engine > Data List
Tester Display
Fuel Press
50003 61 54

e.

Start the engine.


f.

Read the value of Fuel Press while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Press is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A




A

8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4)

B

15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
8.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Val #1 to #4.

Powertrain > Engine > Data List
Tester Display
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
50003 61 368,369,370,371

e.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Val #1
Injection Feedback Val #2
Injection Feedback Val #3
Injection Feedback Val #4
Idling -3.0 mm3/st to 3.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 70°C (158°F) or higher and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Val for at least one cylinder is more than 3 mm3/st and engine vibration is abnormally large B
Except above A


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Val to increase.

·

The ECM controls the system so that the sum of Injection Feedback Val for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Val for a cylinder is less than -3.0 mm3/st (-3.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Val for each of the other cylinders is 3.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.CHECK ENGINE SPEED

B

10.CHECK FREEZE FRAME DATA
9.CHECK ENGINE SPEED
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 60°C (140°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat procedure *1 5 times.

Result:
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B




A

10.CHECK FREEZE FRAME DATA

B

19.READ VALUE USING GTS (ENGINE SPEED)
10.CHECK FREEZE FRAME DATA
a.

Read the value of Injector Leaking Count #1 to #4, and i-ART Learning Status History #1 to #4 in the freeze frame data recorded in Procedure 2.

Result:

If Injector Leaking Count #1 to #4 displays a value of 1 or higher, or i-ART Learning Status History #1 to #4 displays 1 Trip or more, the injector assembly for that cylinder needs to be replaced.


NOTICE:

In order to prevent foreign matter from entering the fuel lines, do not replace the injectors at this time. Replace the injectors after performing step 16.



Result:
Proceed to
NEXT



NEXT

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER
a.

Clean the fuel filter case and replace the fuel filter.

HINT:

Be sure to clean the inside of the fuel filter case as the fuel injectors may not operate properly if the fuel filter is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

13.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
13.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Press, Target Common Rail Pressure, and Target Pump SCV Current.

Powertrain > Engine > Active Test
Active Test Display
Test the Fuel Leak
Data List Display
Target Common Rail Pressure
Fuel Press
Target Pump SCV Current
50004 61 90 706,54,408

e.

Take a snapshot with the GTS during the Active Test.


f.

Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E08
3.406,2.438 3.521,2.104 3.521,2.104 3.594,2.104 false 4.406,2.646 5.01,2.469 5.01,2.469 5.073,2.469 false 3.427,2.646 3.052,1.896 3.052,1.896 3,1.896 true 3.708,3.271 3.938,4.229 3.938,4.229 4.083,4.229 false 0.083,1.448 1.49,1.823 1.406,0.375 10 false Active Test Operation 0.167,0.615 1.604,0.938 1.438,0.323 10 false Engine Speed (rpm) 0.542,3.292 1.448,3.531 0.906,0.24 10 false Fuel Pressure 3.646,2.01 5,2.292 1.354,0.281 10 false Target Fuel Pressure 6.469,4.135 6.948,4.375 0.479,0.24 10 false Time 2.125,2.427 2.802,2.917 0.677,0.49 10 false Less than 10000 kPa 3,4.271 3.917,4.479 0.917,0.208 10 false 2 seconds 5.125,2.375 6.021,2.813 0.896,0.438 10 false Abnormal Fuel Pressure 2.448,1.146 3.125,1.344 0.677,0.198 10 false Test Start 4.177,1.146 4.844,1.344 0.667,0.198 10 false Test Stop 5.625,1.146 6.302,1.344 0.677,0.198 10 false Test Start 2.198,1.813 2.958,2.26 0.76,0.448 10 false Normal Fuel Pressure 1.646,0.302 2.021,0.469 0.375,0.167 10 false 2000 1.885,0.865 2.052,1.031 0.167,0.167 10 false 0 1.75,1.333 2.073,1.5 0.323,0.167 10 false ON 1.698,1.594 2.021,1.76 0.323,0.167 10 false OFF 4.146,4.135 5.729,4.542 1.583,0.406 10 false Pressure Discharge Valve Abnormal Fuel Pressure

OK:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Common Rail Pressure" is the target fuel pressure controlled by the ECM.

·

"Fuel Press" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B




A

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
14.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.

Powertrain > Engine > Active Test
Tester Display
Control the Select Cylinder Fuel Cut
50004 61 231
HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug for all the cylinders.

Click hereEngine / Hybrid System>1KD-FTV STARTING>GLOW PLUG(w/ Glow Plug Controller)>REMOVAL


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug assembly, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPa (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug assembly, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.





Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
16.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:
·

Replace the injector assembly of the cylinder which displays a value of 3.0 mm3/st or higher for Injection Feedback Val #1 to #4 in step 8.

·

Replace the injector assembly determined to be the problem in step 10 and any other injector assemblies which were determined to be malfunctioning in the steps up until this point.



a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

17.BLEED AIR FROM FUEL SYSTEM
17.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS
18.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 70°C (158°F) or higher).


g.

Confirm that the shift lever is in neutral and securely apply the parking brake.


h.

Fully depress the accelerator pedal for 5 seconds, and then release it. (*A)


i.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. (*B)


j.

Repeat procedures (*A) and (*B) 5 times.

A220593E09
1.635,1.854 2.021,2.125 0.385,0.271 10 false 5000 1.469,0.583 1.958,0.854 0.49,0.271 10 false 160000 5.135,2.115 5.781,2.417 0.646,0.302 10 false 3000 rpm 1.865,2.542 1.99,2.719 0.125,0.177 10 false 0 1.854,1.208 1.979,1.385 0.125,0.177 10 false 0 0.073,0.823 1,1.094 0.927,0.271 10 false Fuel Pressure 0.104,2.156 1.146,2.458 1.042,0.302 10 false Engine Speed 0.073,3.448 1.24,3.688 1.167,0.24 10 false Accelerator Pedal 0.948,3.083 2.031,3.313 1.083,0.229 10 false Fully Depressed 1.021,3.719 1.969,3.979 0.948,0.26 10 false Fully Released 2.917,4.219 3.667,4.458 0.75,0.24 10 false 5 seconds 6.448,4.125 6.854,4.313 0.406,0.188 10 false Time 3.104,2.958 3.865,3.198 0.76,0.24 10 false Step (*A) 6.208,2.958 6.813,3.198 0.604,0.24 10 false Step (*A) 4.75,2.958 5.458,3.188 0.708,0.229 10 false Step (*B) 2.104,0.573 2.49,0.844 0.385,0.271 10 false kPa 2.073,1.76 2.417,2.01 0.344,0.25 10 false rpm


k.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 61

l.

Read the DTCs.

OK:

No DTCs are output.



Result:
Proceed to
NEXT



NEXT

END

19.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315

d.

Read the value while cranking and idling the engine.

Standard:
GTS Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine 700 to 800 rpm


HINT:

The value should be the same as the actual engine speed and displayed with no interruption on the GTS.



Result:
Proceed to
OK
NG



OK

20.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

NG

26.REPLACE CRANKSHAFT POSITION SENSOR
20.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A302635C12
1.313,0.188 1.771,0.49 0.458,0.302 0.5,1.51 1.344,0.729 true 0.625,1.729 1.365,0.792 true 0.917,1.719 1.458,0.719 true 1.333,1.917 1.469,0.792 true 1.792,1.917 1.521,0.802 true 1.938,1.729 1.521,0.729 true 2.51,1.76 1.635,0.792 true 2.802,1.583 1.635,0.729 true 0.073,0.021 0.385,0.219 0.313,0.198 10 false *a 1.375,0.24 1.813,0.448 0.438,0.208 10 false C166 0.125,1.75 0.667,1.958 0.542,0.208 10 false 12 (PIJ1) 0.052,1.51 0.594,1.719 0.542,0.208 10 false 6 (EIJ1) 0.771,1.75 1.313,1.958 0.542,0.208 10 false 5 (EIJ2) 1.042,1.958 1.583,2.167 0.542,0.208 10 false 11 (PIJ2) 1.635,1.958 2.177,2.167 0.542,0.208 10 false 10 (PIJ3) 1.969,1.771 2.51,1.979 0.542,0.208 10 false 4 (EIJ3) 2.521,1.771 3.063,1.979 0.542,0.208 10 false 9 (PIJ4) 2.813,1.573 3.354,1.781 0.542,0.208 10 false 3 (EIJ4)
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the injector assembly and ECM.

A192849E07
2.115,1.875 3.073,0.688 3.073,0.688 3.167,0.688 false 3.104,1.875 3.74,1.51 3.74,1.51 3.823,1.51 false 3.854,1.417 5.854,1.969 2,0.552 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.219,0.604 5.396,1.125 2.177,0.521 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.573,0.281 2.302,0.604 0.729,0.323 10 false Example: 4.385,2.615 6.656,2.844 2.271,0.229 10 false Tester Range (Reference): 4.385,2.885 6.781,3.188 2.396,0.302 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C166-12 (PIJ1) - C166-6 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C166-11 (PIJ2) - C166-5 (EIJ2)
C166-10 (PIJ3) - C166-4 (EIJ3)
C166-9 (PIJ4) - C166-3 (EIJ4)



Result:
Result Proceed to
MIL comes on or noise present in the waveform B
Except above A



A

21.CHECK FOR INTERMITTENT PROBLEMS

B

22.REPAIR OR REPLACE HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
21.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS
22.REPAIR OR REPLACE HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

23.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
23.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A302635C12
1.313,0.188 1.771,0.49 0.458,0.302 0.5,1.51 1.344,0.729 true 0.625,1.729 1.365,0.792 true 0.917,1.719 1.458,0.719 true 1.333,1.917 1.469,0.792 true 1.792,1.917 1.521,0.802 true 1.938,1.729 1.521,0.729 true 2.51,1.76 1.635,0.792 true 2.802,1.583 1.635,0.729 true 0.073,0.021 0.385,0.219 0.313,0.198 10 false *a 1.375,0.24 1.813,0.448 0.438,0.208 10 false C166 0.125,1.75 0.667,1.958 0.542,0.208 10 false 12 (PIJ1) 0.052,1.51 0.594,1.719 0.542,0.208 10 false 6 (EIJ1) 0.771,1.75 1.313,1.958 0.542,0.208 10 false 5 (EIJ2) 1.042,1.958 1.583,2.167 0.542,0.208 10 false 11 (PIJ2) 1.635,1.958 2.177,2.167 0.542,0.208 10 false 10 (PIJ3) 1.969,1.771 2.51,1.979 0.542,0.208 10 false 4 (EIJ3) 2.521,1.771 3.063,1.979 0.542,0.208 10 false 9 (PIJ4) 2.813,1.573 3.354,1.781 0.542,0.208 10 false 3 (EIJ4)
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the injector assembly and ECM.

Standard Voltage:
Tester Connection Condition Specified Condition
C166-12 (PIJ1) - C166-6 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C166-11 (PIJ2) - C166-5 (EIJ2)
C166-10 (PIJ3) - C166-4 (EIJ3)
C166-9 (PIJ4) - C166-3 (EIJ4)



Result:
Result Proceed to
MIL comes on or noise present in the waveform A
Except above B



A

24.REPLACE INJECTOR ASSEMBLY (FUEL PRESSURE SENSOR)

B

18.CHECK WHETHER DTC OUTPUT RECURS
24.REPLACE INJECTOR ASSEMBLY (FUEL PRESSURE SENSOR)
a.

Replace the injector assembly.

Click hereEngine / Hybrid System>1KD-FTV FUEL>FUEL INJECTOR(w/ Glow Plug Controller)>REMOVAL

HINT:

Before replacing the injector assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.


NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.

·

Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

25.BLEED AIR FROM FUEL SYSTEM
25.BLEED AIR FROM FUEL SYSTEM

Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS
26.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>CRANKSHAFT POSITION SENSOR>REMOVAL

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER DTC OUTPUT RECURS