Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  VC Output Circuit  


DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.

A206916E28
4.385,1.208 6.208,1.438 1.823,0.229 10 false 5 V Constant Voltage Circuit 5.375,2.083 6.385,2.302 1.01,0.219 10 false Microprocessor 1.719,1.156 2.771,1.323 1.052,0.167 10 false from EFI Fuse 1.698,1.49 2.74,1.719 1.042,0.229 10 false from EFI Relay 2.938,1.031 3.458,1.25 0.521,0.219 10 false BATT 0.365,2.177 2.677,2.792 2.313,0.615 10 false Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (sensors which have ICs) 0.344,3.021 2.708,3.448 2.365,0.427 10 false Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.125 4.333,3.333 0.26,0.208 10 false R 3,1.385 3.281,1.583 0.281,0.198 10 false +B 3.188,2.177 3.458,2.375 0.271,0.198 10 false VC 4.875,3.396 5.323,3.625 0.448,0.229 10 false ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A279712E02
0.073,4.823 0.344,4.99 0.271,0.167 10 false C9 0.083,3.125 0.396,3.292 0.313,0.167 10 false G6 0.885,1.083 1.219,1.281 0.333,0.198 10 false EPA 0.833,2.427 1.25,2.667 0.417,0.24 10 false EPA2 0.823,1.969 1.24,2.198 0.417,0.229 10 false VPA2 0.792,1.521 1.25,1.719 0.458,0.198 10 false VCPA 0.885,0.646 1.208,0.844 0.323,0.198 10 false VPA 0.823,2.885 1.219,3.083 0.396,0.198 10 false VCP2 1.302,0.74 1.458,0.917 0.156,0.177 10 false 6 1.302,1.177 1.458,1.354 0.156,0.177 10 false 5 1.313,1.646 1.469,1.823 0.156,0.177 10 false 4 1.302,2.073 1.458,2.25 0.156,0.177 10 false 3 1.302,2.521 1.458,2.698 0.156,0.177 10 false 2 1.302,2.969 1.458,3.146 0.156,0.177 10 false 1 5.646,1.74 5.802,1.917 0.156,0.177 10 false 1 5.656,0.406 5.813,0.583 0.156,0.177 10 false 2 5.646,0.865 5.802,1.042 0.156,0.177 10 false 5 5.646,1.323 5.802,1.5 0.156,0.177 10 false 6 5.656,2.198 5.813,2.375 0.156,0.177 10 false 3 5.656,2.656 5.813,2.833 0.156,0.177 10 false 4 5.927,1.083 6.25,1.333 0.323,0.25 10 false EPA 5.938,2.427 6.333,2.667 0.396,0.24 10 false EPA2 5.938,2 6.333,2.25 0.396,0.25 10 false VPA2 5.938,1.542 6.417,1.833 0.479,0.292 10 false VCPA 5.927,0.625 6.333,0.917 0.406,0.292 10 false VPA 5.948,2.885 6.417,3.083 0.469,0.198 10 false VCP2 5.49,1.969 5.927,2.146 0.438,0.177 10 false G157 5.5,0.635 5.885,0.813 0.385,0.177 10 false G157 5.5,2.896 5.938,3.073 0.438,0.177 10 false G156 5.5,2.427 5.938,2.604 0.438,0.177 10 false G156 5.5,1.542 5.865,1.719 0.365,0.177 10 false G156 5.49,1.083 5.885,1.26 0.396,0.177 10 false G156 1.021,4.594 1.25,4.833 0.229,0.24 10 false E2 0.906,4.146 1.25,4.333 0.344,0.188 10 false VTA 1,3.708 1.25,3.885 0.25,0.177 10 false VC 1.292,4.219 1.448,4.396 0.156,0.177 10 false 3 1.302,4.688 1.458,4.865 0.156,0.177 10 false 2 1.302,3.771 1.458,3.948 0.156,0.177 10 false 1 5.927,4.583 6.406,4.76 0.479,0.177 10 false EVLU 5.927,4.146 6.313,4.323 0.385,0.177 10 false VLU 5.927,3.708 6.5,4 0.573,0.292 10 false VCVL 5.5,4.156 5.927,4.333 0.427,0.177 10 false C166 5.646,3.917 5.802,4.094 0.156,0.177 10 false 8 5.656,4.365 5.813,4.542 0.156,0.177 10 false 2 5.604,3.438 5.771,3.615 0.167,0.177 10 false 14 6.25,8.531 6.656,8.771 0.406,0.24 10 false ECM 0.115,3.292 2.281,3.448 2.167,0.156 10 false Accelerator Pedal Position Sensor 0.073,4.99 1.635,5.156 1.563,0.167 10 false Throttle Position Sensor 5.5,3.698 5.927,3.875 0.427,0.177 10 false C166 5.479,4.594 5.906,4.771 0.427,0.177 10 false C166 0.063,6.594 0.49,6.76 0.427,0.167 10 false C120 1.063,6.333 1.25,6.51 0.188,0.177 10 false E2 0.979,5.875 1.281,6.052 0.302,0.177 10 false VTA 1.052,5.417 1.302,5.594 0.25,0.177 10 false VC 1.292,6.427 1.448,6.604 0.156,0.177 10 false 1 1.292,5.99 1.448,6.167 0.156,0.177 10 false 2 1.292,5.542 1.448,5.719 0.156,0.177 10 false 3 5.948,6.313 6.427,6.49 0.479,0.177 10 false EEGL 5.948,5.875 6.417,6.052 0.469,0.177 10 false EGRA 5.938,5.427 6.375,5.604 0.438,0.177 10 false VCEG 5.5,5.865 5.927,6.042 0.427,0.177 10 false C166 5.635,5.667 5.896,5.844 0.26,0.177 10 false 7 5.646,6.104 5.802,6.281 0.156,0.177 10 false 1 5.604,5.177 5.854,5.354 0.25,0.177 10 false 13 0.104,6.75 2.302,6.917 2.198,0.167 10 false EGR Valve Position Sensor 5.5,5.427 5.927,5.604 0.427,0.177 10 false C166 5.5,6.333 5.927,6.51 0.427,0.177 10 false C166 0.094,8.354 0.385,8.521 0.292,0.167 10 false C20 1.083,8.073 1.271,8.25 0.188,0.177 10 false E 0.938,7.656 1.229,7.833 0.292,0.177 10 false PIM 1,7.219 1.25,7.396 0.25,0.177 10 false VC 1.313,7.74 1.469,7.917 0.156,0.177 10 false 2 1.302,8.188 1.458,8.365 0.156,0.177 10 false 1 1.302,7.281 1.458,7.458 0.156,0.177 10 false 3 5.938,8.052 6.417,8.229 0.479,0.177 10 false EPIM 5.938,7.615 6.323,7.792 0.385,0.177 10 false PIM 5.948,7.198 6.385,7.375 0.438,0.177 10 false VCPM 5.5,7.625 5.927,7.802 0.427,0.177 10 false C167 5.615,7.406 5.875,7.583 0.26,0.177 10 false 12 5.635,7.865 5.792,8.042 0.156,0.177 10 false 6 5.594,6.938 5.833,7.115 0.24,0.177 10 false 18 0.104,8.521 2.74,8.688 2.635,0.167 10 false Manifold Absolute Pressure Sensor 5.5,7.188 5.927,7.365 0.427,0.177 10 false C167 5.5,8.083 5.927,8.26 0.427,0.177 10 false C167

A279713E01
6.303,9.512 6.639,9.682 0.336,0.170 10 ECM 0.162,1.788 0.491,1.967 0.329,0.179 10 C40 1.331,1.176 1.487,1.358 0.156,0.181 10 1 1.331,0.743 1.487,0.924 0.156,0.181 10 3 1.331,1.62 1.487,1.801 0.156,0.181 10 2 5.511,0.632 5.921,0.813 0.410,0.181 10 C167 5.602,0.394 5.806,0.575 0.205,0.181 10 17 0.88,1.087 1.313,1.269 0.433,0.181 10 VTA1 0.796,0.632 1.214,0.813 0.418,0.181 10 VNVC 0.852,1.536 1.323,1.717 0.471,0.181 10 VNE2 5.941,0.646 6.374,0.827 0.433,0.181 10 VNVC 0.162,1.942 2.037,2.128 1.875,0.186 10 Nozzle Vane Position Sensor 5.511,1.087 5.921,1.269 0.410,0.181 10 C167 5.595,0.863 5.799,1.045 0.205,0.181 10 11 5.934,1.088 6.367,1.269 0.433,0.181 10 VNA 5.511,1.536 5.921,1.717 0.410,0.181 10 C167 5.623,1.312 5.827,1.493 0.205,0.181 10 5 5.948,1.536 6.381,1.717 0.433,0.181 10 VNE2 0.162,3.665 0.574,3.844 0.412,0.179 10 C159 1.331,3.054 1.487,3.235 0.156,0.181 10 4 1.331,2.62 1.487,2.802 0.156,0.181 10 2 1.331,3.497 1.487,3.679 0.156,0.181 10 1 5.511,2.509 5.921,2.691 0.410,0.181 10 C166 5.616,2.271 5.820,2.453 0.205,0.181 10 18 0.936,2.965 1.279,3.146 0.343,0.181 10 PIJ1 0.936,2.509 1.271,2.691 0.335,0.181 10 VIJ1 0.908,3.413 1.261,3.594 0.353,0.181 10 EIJ1 5.941,2.51 6.374,2.691 0.433,0.181 10 VIJ1 0.162,3.819 2.037,4.005 1.875,0.186 10 No. 1 Injector Assembly 5.511,2.965 5.921,3.146 0.410,0.181 10 C166 5.595,2.741 5.799,2.922 0.205,0.181 10 12 5.934,2.979 6.367,3.160 0.433,0.181 10 PIJ1 5.511,3.413 5.921,3.594 0.410,0.181 10 C166 5.637,3.189 5.841,3.370 0.205,0.181 10 6 5.948,3.413 6.381,3.594 0.433,0.181 10 EIJ1 0.162,5.542 0.574,5.721 0.412,0.179 10 C160 1.331,4.931 1.487,5.112 0.156,0.181 10 4 1.331,4.498 1.487,4.679 0.156,0.181 10 2 1.331,5.375 1.487,5.556 0.156,0.181 10 1 5.511,4.387 5.921,4.568 0.410,0.181 10 C166 5.616,4.149 5.820,4.330 0.205,0.181 10 17 0.922,4.842 1.265,5.023 0.343,0.181 10 PIJ2 0.922,4.387 1.257,4.568 0.335,0.181 10 VIJ2 0.894,5.291 1.247,5.472 0.353,0.181 10 EIJ2 5.927,4.401 6.360,4.582 0.433,0.181 10 VIJ2 0.162,5.697 2.037,5.883 1.875,0.186 10 No. 2 Injector Assembly 5.511,4.842 5.921,5.023 0.410,0.181 10 C166 5.595,4.618 5.799,4.799 0.205,0.181 10 11 5.92,4.856 6.353,5.038 0.433,0.181 10 PIJ2 5.511,5.29 5.921,5.472 0.410,0.181 10 C166 5.623,5.066 5.827,5.248 0.205,0.181 10 5 5.934,5.291 6.367,5.472 0.433,0.181 10 EIJ2 0.162,7.42 0.574,7.599 0.412,0.179 10 C161 1.331,6.808 1.487,6.990 0.156,0.181 10 4 1.331,6.375 1.487,6.556 0.156,0.181 10 2 1.331,7.252 1.487,7.434 0.156,0.181 10 1 5.511,6.264 5.921,6.445 0.410,0.181 10 C166 5.616,6.026 5.820,6.207 0.205,0.181 10 16 0.936,6.72 1.279,6.901 0.343,0.181 10 PIJ3 0.936,6.264 1.271,6.446 0.335,0.181 10 VIJ3 0.908,7.168 1.261,7.349 0.353,0.181 10 EIJ3 5.941,6.278 6.374,6.460 0.433,0.181 10 VIJ3 0.162,7.574 2.037,7.760 1.875,0.186 10 No. 3 Injector Assembly 5.511,6.719 5.921,6.901 0.410,0.181 10 C166 5.595,6.496 5.799,6.677 0.205,0.181 10 10 5.934,6.734 6.367,6.915 0.433,0.181 10 PIJ3 5.511,7.168 5.921,7.349 0.410,0.181 10 C166 5.623,6.944 5.827,7.125 0.205,0.181 10 4 5.948,7.168 6.381,7.349 0.433,0.181 10 EIJ3 0.162,9.311 0.574,9.490 0.412,0.179 10 C162 1.331,8.7 1.487,8.881 0.156,0.181 10 4 1.331,8.267 1.487,8.448 0.156,0.181 10 2 1.331,9.144 1.487,9.325 0.156,0.181 10 1 5.511,8.156 5.921,8.337 0.410,0.181 10 C166 5.587,7.918 5.792,8.099 0.205,0.181 10 15 0.95,8.611 1.293,8.792 0.343,0.181 10 PIJ4 0.95,8.156 1.285,8.337 0.335,0.181 10 VIJ4 0.922,9.059 1.275,9.241 0.353,0.181 10 EIJ4 5.955,8.142 6.388,8.323 0.433,0.181 10 VIJ4 5.511,8.611 5.921,8.792 0.410,0.181 10 C166 5.623,8.387 5.827,8.568 0.205,0.181 10 9 5.948,8.597 6.381,8.778 0.433,0.181 10 PIJ4 5.511,9.059 5.921,9.240 0.410,0.181 10 C166 5.637,8.835 5.841,9.017 0.205,0.181 10 3 5.962,9.045 6.395,9.227 0.433,0.181 10 EIJ4 0.162,9.486 2.037,9.672 1.875,0.186 10 No. 4 Injector Assembly

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


PROCEDURE

1.CHECK MIL
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B




A

END

B

2.CHECK COMMUNICATION BETWEEN GTS AND ECM
2.CHECK COMMUNICATION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and GTS on.


c.

Check the communication between the GTS and ECM.

Result:
Result Proceed to
Communication is possible A
Communication is not possible B




A

B

3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
3.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
a.

Disconnect the G6 accelerator pedal position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the accelerator pedal position sensor connector.



A

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

B

4.CHECK MIL (THROTTLE POSITION SENSOR)
4.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the C9 throttle position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the throttle position sensor connector.



A

B

5.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
5.CHECK MIL (ELECTRIC EGR CONTROL VALVE ASSEMBLY)
a.

Disconnect the C120 electric EGR control valve assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the electric EGR control valve assembly connector.



A

B

6.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
6.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the C20 manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the manifold absolute pressure sensor connector.



A

B

7.CHECK MIL (NO. 1 INJECTOR ASSEMBLY)
7.CHECK MIL (NO. 1 INJECTOR ASSEMBLY)
a.

Disconnect the C159 No. 1 injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the No. 1 injector assembly connector.



A

B

8.CHECK MIL (NO. 2 INJECTOR ASSEMBLY)
8.CHECK MIL (NO. 2 INJECTOR ASSEMBLY)
a.

Disconnect the C160 No. 2 injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the No. 2 injector assembly connector.



A

B

9.CHECK MIL (NO. 3 INJECTOR ASSEMBLY)
9.CHECK MIL (NO. 3 INJECTOR ASSEMBLY)
a.

Disconnect the C161 No. 3 injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the No. 3 injector assembly connector.



A

B

10.CHECK MIL (NO. 4 INJECTOR ASSEMBLY)
10.CHECK MIL (NO. 4 INJECTOR ASSEMBLY)
a.

Disconnect the C162 No. 4 injector assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the No. 4 injector assembly connector.



A

B

11.CHECK MIL (NOZZLE VANE POSITION SENSOR)
11.CHECK MIL (NOZZLE VANE POSITION SENSOR)
a.

Disconnect the C40 nozzle vane position sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL illuminates A
MIL does not illuminate B



d.

Reconnect the nozzle vane position sensor connector.



A

B

12.CHECK HARNESS AND CONNECTOR
12.CHECK HARNESS AND CONNECTOR
a.

Disconnect the G6 accelerator pedal position sensor connector.


b.

Disconnect the C9 throttle position sensor connector.


c.

Disconnect the C120 electric EGR control valve assembly connector.


d.

Disconnect the C40 nozzle vane position sensor connector.


e.

Disconnect the C20 manifold absolute pressure sensor connector.


f.

Disconnect the C159 No. 1 injector assembly connector.


g.

Disconnect the C160 No. 2 injector assembly connector.


h.

Disconnect the C161 No. 3 injector assembly connector.


i.

Disconnect the C162 No. 4 injector assembly connector.


j.

Disconnect the C166 ECM connectors.


k.

Disconnect the C167 ECM connectors.


l.

Disconnect the G156 ECM connectors.


m.

Disconnect the G157 ECM connectors.


n.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G156-6 (VCPA) - Body ground Always 10 kΩ or higher
G156-4 (VCP2) - Body ground Always 10 kΩ or higher
C166-14 (VCVL) - Body ground Always 10 kΩ or higher
C166-13 (VCEG) - Body ground Always 10 kΩ or higher
C167-18 (VCPM) - Body ground Always 10 kΩ or higher
C167-17 (VNVC) - Body ground Always 10 kΩ or higher
C166-18 (VIJ1) - Body ground Always 10 kΩ or higher
C166-17 (VIJ2) - Body ground Always 10 kΩ or higher
C166-16 (VIJ3) - Body ground Always 10 kΩ or higher
C166-15 (VIJ4) - Body ground Always 10 kΩ or higher



o.

Reconnect the accelerator pedal position sensor connector.


p.

Reconnect the throttle position sensor connector.


q.

Reconnect the electric EGR control valve assembly connector.


r.

Reconnect the nozzle vane position sensor connector.


s.

Reconnect the manifold absolute pressure sensor connector.


t.

Reconnect the No. 1 injector assembly connector.


u.

Reconnect the No. 2 injector assembly connector.


v.

Reconnect the No. 3 injector assembly connector.


w.

Reconnect the No. 4 injector assembly connector.


x.

Reconnect the ECM connectors.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR