Home › Engine / Hybrid System › 1KD-FTV ENGINE CONTROL › ECD SYSTEM(for i-ART) › from 2012.10
RM1840EF _51 Engine / Hybrid System _009570 1KD-FTV ENGINE CONTROL _0052110 ECD SYSTEM(for i-ART) J

1KD-FTV ENGINE CONTROL  ECD SYSTEM(for i-ART)  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned to ON, power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the ignition switch is first turned to ON, the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A255258E45
0.99,0.917 1.302,1.073 0.313,0.156 10 false G9 0.99,1.073 1.948,1.25 0.958,0.177 10 false Ignition Switch 3.271,3.083 5.365,3.365 2.094,0.281 10 false Combination Meter Assembly 3.604,2.625 3.865,2.771 0.26,0.146 10 false MIL 6.375,3.438 6.75,3.635 0.375,0.198 10 false ECM 6.208,2.458 6.396,2.604 0.188,0.146 10 false W 2.573,1.479 3,1.625 0.427,0.146 10 false MET 0.833,2.667 1.375,2.938 0.542,0.271 10 false Battery 0.688,1.479 1.01,1.625 0.323,0.146 10 false AM2 1.781,0.667 2.031,0.813 0.25,0.146 10 false IG2 1.094,0.667 1.417,0.813 0.323,0.146 10 false AM2 2.104,0.469 2.208,0.615 0.104,0.146 10 false 6 0.948,0.469 1.052,0.615 0.104,0.146 10 false 5 5.938,2.385 6.115,2.531 0.177,0.146 10 false 19 6.365,3.281 6.844,3.479 0.479,0.198 10 false G157 4.823,2.385 5.01,2.531 0.188,0.146 10 false 39 3.063,2.385 3.25,2.531 0.188,0.146 10 false 21 3.281,2.927 3.708,3.073 0.427,0.146 10 false G19 4.396,2.365 4.74,2.51 0.344,0.146 10 false CHK 3.323,2.365 3.667,2.51 0.344,0.146 10 false IG+

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>REGISTRATION) and initialization (See page Engine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>INITIALIZATION).


PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Check the MIL illumination condition.

Result:
Condition Proceed to
MIL remains on A
MIL does not illuminate B




A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Check if DTCs have been stored.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Trouble Codes
50001 61

d.

If DTCs are output, write them down.


e.

Clear the DTCs.

Click hereEngine / Hybrid System>1KD-FTV ENGINE CONTROL>ECD SYSTEM(for i-ART)>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 61

f.

Check that the MIL turns off.

OK:

MIL turns off.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.



d.

Reconnect the ECM connector.


Result:
Proceed to
OK
NG



OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-39 (CHK) - G157-19 (W) Always Below 1 Ω
G19-39 (CHK) or G157-19 (W) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination assembly meter connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the ignition switch is turned to ON.

OK:

MIL is illuminated.



Result:
Proceed to
OK
NG



OK

SYSTEM OK

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

Start the engine.

Result:
Result Proceed to
Engine starts A
Engine does not start* B


HINT:

*: The GTS cannot communicate with the ECM.




A

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)

B

7.INSPECT COMBINATION METER ASSEMBLY (MIL CIRCUIT)
a.

Refer to the combination meter troubleshooting procedure.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER ASSEMBLY - ECM)