Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

This circuit sends an operation signal from the steering pad switch assembly to the navigation receiver assembly.

If there is an open in the circuit, the audio system cannot be operated using the steering pad switch assembly.

If there is a short in the circuit, the same condition as when a switch is continuously depressed occurs.

Therefore, the navigation receiver assembly cannot be operated using the steering pad switch assembly, and also the navigation receiver assembly itself cannot function.

WIRING DIAGRAM

E276992
4.688,0.365 4.896,0.573 0.208,0.208 10 false 10 0.74,1.094 1.354,1.292 0.615,0.198 10 false VOL- 1.531,1.094 2.146,1.292 0.615,0.198 10 false VOL+ 2.156,1.104 2.771,1.302 0.615,0.198 10 false SEEK- 2.813,1.094 3.427,1.292 0.615,0.198 10 false SEEK+ 2.542,2.208 3.156,2.406 0.615,0.198 10 false MODE 1.292,3.01 3.594,3.271 2.302,0.26 10 false Steering Pad Switch LH Side 0.677,4.49 1.292,4.688 0.615,0.198 10 false VOICE 1.417,4.427 1.781,4.583 0.365,0.156 10 false OFF 2.229,4.427 2.573,4.583 0.344,0.156 10 false ON 1.333,5.406 3.635,5.667 2.302,0.26 10 false Steering Pad Switch RH Side 1.292,6.042 3.594,6.302 2.302,0.26 10 false Steering Pad Switch Assembly 4.656,3.292 5.646,3.646 0.99,0.354 10 false Spiral Cable Sub-assembly 4.729,1.448 4.938,1.656 0.208,0.208 10 false 8 4.729,2.583 4.938,2.792 0.208,0.208 10 false 9 5.583,2.583 5.792,2.792 0.208,0.208 10 false 5 5.563,1.479 5.771,1.688 0.208,0.208 10 false 4 5.583,0.354 5.792,0.563 0.208,0.208 10 false 6 4.698,0.552 4.906,0.76 0.208,0.208 10 false z3 4.688,1.656 4.896,1.865 0.208,0.208 10 false z3 4.688,2.771 4.896,2.979 0.208,0.208 10 false z3 5.5,2.781 5.823,3.01 0.323,0.229 10 false G12 5.49,1.667 5.813,1.896 0.323,0.229 10 false G12 5.5,0.563 5.823,0.792 0.323,0.229 10 false G12 5.042,0.458 5.365,0.688 0.323,0.229 10 false AU1 5.052,1.563 5.375,1.792 0.323,0.229 10 false EAU 5.052,2.667 5.375,2.896 0.323,0.229 10 false AU2 6.375,0.552 6.885,0.802 0.51,0.25 10 false SW1 6.365,1.646 6.958,1.885 0.594,0.24 10 false SWG 6.385,2.792 7.052,3.083 0.667,0.292 10 false SW2 6.135,2.656 6.542,2.896 0.406,0.24 10 false 22 6.104,1.552 6.51,1.792 0.406,0.24 10 false 23 6.125,0.438 6.531,0.677 0.406,0.24 10 false 21 5.917,3.25 6.49,3.417 0.573,0.167 10 false G152 5.906,3.406 7.156,3.781 1.25,0.375 10 false Navigation Receiver Assembly 1.438,4.583 1.917,4.76 0.479,0.177 10 false HOOK 2.25,4.583 2.708,4.74 0.458,0.156 10 false HOOK

CAUTION / NOTICE / HINT

NOTICE:

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION


PROCEDURE

1.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

2.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the G12 spiral cable sub-assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-21 (SW1) - G12-6 (AU1) Always Below 1 Ω
G152-22 (SW2) - G12-5 (AU2) Always Below 1 Ω
G152-23 (SWG) - G12-4 (EAU) Always Below 1 Ω
G152-21 (SW1) - Body ground Always 10 kΩ or higher
G152-22 (SW2) - Body ground Always 10 kΩ or higher
G152-23 (SWG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR