Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009632 NAVIGATION / MULTI INFO DISPLAY _0052661 NAVIGATION SYSTEM J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM  Reverse Signal Circuit  


DESCRIPTION

The navigation receiver assembly receives a reverse signal from the park/neutral position switch assembly*1 or back-up light switch assembly*2.

*1: for Automatic Transmission

*2: for Manual Transmission


WIRING DIAGRAM

E282018
1.625,0.76 1.938,0.958 0.313,0.198 10 false RL 1.958,0.604 2.271,0.802 0.313,0.198 10 false 1 1.969,1.969 2.281,2.167 0.313,0.198 10 false 1 0.771,1.292 1.083,1.49 0.313,0.198 10 false C57 5.125,0.646 5.438,0.844 0.313,0.198 10 false 2 5.344,0.781 5.948,0.979 0.604,0.198 10 false REV 5.146,1.302 5.75,1.5 0.604,0.198 10 false G152 5.156,1.5 7.031,1.781 1.875,0.281 10 false Navigation Receiver Assembly 0.771,1.458 3.417,1.635 2.646,0.177 10 false Park/Neutral Position Switch Assembly*1 0.677,2.667 2.542,2.844 1.865,0.177 10 false C165*3, C87*4 0.688,2.833 2.833,3.031 2.146,0.198 10 false Back-up Light Switch Assembly*2 0.156,3.188 2.302,3.385 2.146,0.198 10 false *1: for Automatic Transmission 0.167,3.469 2.313,3.667 2.146,0.198 10 false *2: for Manual Transmission 2.333,3.208 4.479,3.406 2.146,0.198 10 false *3: for 1KD-FTV with i-ART 2.323,3.469 4.469,3.667 2.146,0.198 10 false *4: except 1KD-FTV with i-ART

PROCEDURE

1.CHECK VEHICLE SIGNAL (OPERATION CHECK)
a.
E282021

Enter the "Vehicle Signal Check Mode" screen. Refer to check Vehicle Signal in Operation Check.

Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK


b.

Check that the display changes between ON and OFF according to the shift lever position.

OK:
Shift Lever Position Display
R ON
Except R OFF


HINT:

This display is updated once per second. As a result, it is normal for the display to lag behind the actual shift lever position.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK NAVIGATION RECEIVER ASSEMBLY
2.CHECK NAVIGATION RECEIVER ASSEMBLY
a.
E140414
1.427,0.448 2.031,0.729 0.604,0.281 0.948,1.385 0.615,0.802 0.615,0.802 0.479,0.802 true 0.063,0.063 0.302,0.25 0.24,0.188 10 false *a 1.573,0.49 1.938,0.677 0.365,0.188 10 false G152 0.167,0.729 0.5,0.896 0.333,0.167 10 false REV
*a Front view of wire harness connector
(to Navigation Receiver Assembly)


Disconnect the G152 navigation receiver assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G152-2 (REV) - Body ground Ignition switch ON, shift lever in R 7.5 to 14 V
G152-2 (REV) - Body ground Ignition switch ON, shift lever not in R Below 1 V



Result:
Proceed to
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)



OK

NG (for Automatic Transmission)

3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)

NG (for Manual Transmission)

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)
3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the C57 park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-2 (REV) - C57-1 (RL) Always Below 1 Ω
G152-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for A343E)
OK (for A343F)
OK (for 750F)
NG



OK (for A343E)

OK (for A343F)

OK (for 750F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - BACK-UP LIGHT SWITCH ASSEMBLY)

*1: for 1KD-FTV with i-ART

*2: except 1KD-FTV with i-ART


a.

Disconnect the G152 navigation receiver assembly connector.


b.

Disconnect the C165*1 or C87*2 back-up light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G152-2 (REV) - C165-1*1 Always Below 1 Ω
G152-2 (REV) - C87-1*2 Always Below 1 Ω
G152-2 (REV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK (for R150 or R151)
OK (for R150F or R151F)
NG



OK (for R150 or R151)

OK (for R150F or R151F)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR