The radio and display receiver assembly sends sound signals to the speakers.
Enter the "System Check Mode" screen. (Refer to Check SP Check On in Operation Check)
Check the malfunctioning speakers.
| Proceed to |
|---|
| Malfunction in front speaker area |
| Malfunction in rear speaker area |
Malfunction in front speaker area
Malfunction in rear speaker area
Disconnect the G129 radio and display receiver assembly connector.
Disconnect the H6*1 and/or I6*2 front No. 2 speaker assembly connector.
*1: for RH Side
*2: for LH Side
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G129-1 (FR+) - H6-4 (TWR+) | Always | Below 1 Ω |
| G129-5 (FR-) - H6-2 (TWR-) | ||
| G129-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| G129-5 (FR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G129-2 (FL+) - I6-4 (TWL+) | Always | Below 1 Ω |
| G129-6 (FL-) - I6-2 (TWL-) | ||
| G129-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| G129-6 (FL-) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for RH Side
*2: for LH Side
Disconnect the H6*1 and/or I6*2 front No. 2 speaker assembly connector.
Disconnect the H4*1 and/or I1*2 front No. 1 speaker assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H6-3 (+) - H4-1 | Always | Below 1 Ω |
| H6-1 (-) - H4-2 | ||
| H6-3 (+) - Body ground | Always | 10 kΩ or higher |
| H6-1 (-) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I6-3 (+) - I1-1 | Always | Below 1 Ω |
| I6-1 (-) - I1-2 | ||
| I6-3 (+) - Body ground | Always | 10 kΩ or higher |
| I6-1 (-) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H4*1 and/or I1*2 front No. 1 speaker assembly connector.
*1: for RH Side
*2: for LH Side
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Check that the malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both LH and RH sides.
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G128 radio and display receiver assembly connector.
Disconnect the J7*1 and/or J3*2 rear speaker assembly connector.
*1: for RH Side
*2: for LH Side
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G128-1 (RR+) - J7-1 | Always | Below 1 Ω |
| G128-3 (RR-) - J7-2 | ||
| G128-1 (RR+) - Body ground | Always | 10 kΩ or higher |
| G128-3 (RR-) - Body ground |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G128-2 (RL+) - J3-1 | Always | Below 1 Ω |
| G128-6 (RL-) - J3-2 | ||
| G128-2 (RL+) - Body ground | Always | 10 kΩ or higher |
| G128-6 (RL-) - Body ground |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J7*1 and/or J3*2 rear speaker assembly connector.
*1: for RH Side
*2: for LH Side
Inspect the rear speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
| Proceed to |
|---|
| OK |
| NG |
OK
NG