Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM(for Radio and Display Type) › from 2013.10
RM1840EF _56 Audio / Visual / Telematics _009631 AUDIO / VIDEO _0052657 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) J

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  Microphone Circuit between Microphone and Radio Receiver  


DESCRIPTION

Microphone signal from the telephone microphone assembly is sent to the radio and display receiver assembly. Also, power is supplied from the radio and display receiver assembly to the telephone microphone assembly.

WIRING DIAGRAM

E277658
5.885,0.604 6.5,0.802 0.615,0.198 10 false MACC 5.885,1.083 6.5,1.281 0.615,0.198 10 false MIN+ 5.885,1.563 6.5,1.76 0.615,0.198 10 false MIN- 5.885,2.031 6.5,2.229 0.615,0.198 10 false SGND 5.885,2.51 6.5,2.708 0.615,0.198 10 false SNS2 5.688,0.5 6.302,0.698 0.615,0.198 10 false 4 5.688,0.969 6.302,1.167 0.615,0.198 10 false 5 5.615,1.448 6.229,1.646 0.615,0.198 10 false 19 5.635,1.906 6.25,2.104 0.615,0.198 10 false 18 5.667,2.385 6.281,2.583 0.615,0.198 10 false 6 5.771,2.938 6.385,3.135 0.615,0.198 10 false G127 5.781,3.115 6.99,3.531 1.208,0.417 10 false Radio and Display Receiver Assembly 4.604,2.167 5.438,2.365 0.833,0.198 10 false Shielded 3.417,2.167 4.25,2.365 0.833,0.198 10 false Shielded 1.823,0.5 2.438,0.698 0.615,0.198 10 false MACC 1.844,0.969 2.458,1.167 0.615,0.198 10 false MCO+ 1.865,1.448 2.479,1.646 0.615,0.198 10 false MCO- 2.385,0.5 3,0.698 0.615,0.198 10 false 4 2.385,0.958 3,1.156 0.615,0.198 10 false 3 2.385,1.417 3,1.615 0.615,0.198 10 false 2 0.458,1.865 1.958,2.198 1.5,0.333 10 false Telephone Microphone Assembly 0.813,2.604 1.427,2.802 0.615,0.198 10 false N2 0.813,2.771 2.813,3.021 2,0.25 10 false Map Light Assembly

PROCEDURE

1.CHECK TELEPHONE TRANSCEIVER ASSEMBLY (OPERATION CHECK)
a.

Enter the "Microphone Check" screen. (Refer to Microphone and Voice Recognition Check in Operation Check)

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>AUDIO AND VISUAL SYSTEM(for Radio and Display Type)>OPERATION CHECK


b.
E268457

When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.



c.

Push the recording switch and perform voice recording.

HINT:
·

Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

·

Voice can be recorded for up to 5 seconds.




d.

w/ Recording Function:

i.

Check that the recording indicator remains on while recording and that the recorded voice is played normally without noise or distortion.



Result:
Proceed to
OK
NG



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
a.

Disconnect the G127 radio and display receiver assembly connector.


b.

Disconnect the N2 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-4 (MACC) - N2-4 (MACC) Always Below 1 Ω
G127-5 (MIN+) - N2-3 (MCO+)
G127-19 (MIN-) - N2-2 (MCO-)
G127-6 (SNS2) - Body ground
G127-4 (MACC) - Body ground Always 10 kΩ or higher
G127-5 (MIN+) - Body ground
G127-19 (MIN-) - Body ground
G127-18 (SGND) - Body ground



Result:
Proceed to
OK
NG



OK

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.
E237416
1.448,0.448 1.979,0.688 0.531,0.24 2.208,1.75 2.469,0.875 2.469,0.875 2.719,0.875 true 2.219,2 2.552,2.49 2.552,2.49 2.802,2.49 true 2.417,2.75 2.167,2.75 2.167,2.75 2.083,2.01 true 0.083,0.094 0.396,0.292 0.313,0.198 10 false *a 1.552,0.479 1.99,0.698 0.438,0.219 10 false G127 2.75,0.781 3.25,1.01 0.5,0.229 10 false MACC 2.833,2.406 3.302,2.583 0.469,0.177 10 false SGND 2.458,2.667 2.792,2.906 0.333,0.24 10 false MIN-
*a Component with harness connected
(Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G127-18 (SGND) - Body ground Always Below 1 Ω
G127-19 (MIN-) - Body ground



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G127-4 (MACC) - Body ground Ignition switch ACC 4 to 6 V



Result:
Proceed to
OK
NG



OK

4.CHECK TELEPHONE MICROPHONE ASSEMBLY

NG

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

4.CHECK TELEPHONE MICROPHONE ASSEMBLY
a.

Replace the telephone microphone assembly with a known good one.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>TELEPHONE MICROPHONE>REMOVAL


b.

Check that the malfunction disappears.

OK:

Malfunction disappears.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)

NG

REPLACE MAP LIGHT ASSEMBLY