Refer to DTC P2716 (See page Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)>P2716).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0894 | Transmission Component Slipping | The TCM detects a malfunction of the SLT, S1, S2, SR, SL1, SL2 or 1-2 shift solenoid valves according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic). | ·
Shift solenoid valve SLT remains open or closed ·
Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed ·
1-2 shift valve is stuck ·
Valve body is blocked ·
Automatic transmission (clutch, brake or gear, etc.) |
Comes on | DTC stored |
| P2714 | Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT) | The TCM detects a malfunction of the SLT shift solenoid valve (ON side) according to the revolution difference of the turbine and output shaft, and also by the oil pressure (2 trip detection logic). | ·
Shift solenoid valve SLT remains open or closed ·
Shift solenoid valve S1, S2, SR, SL1 or SL2 remains open or closed ·
1-2 shift valve is stuck ·
Valve body is blocked ·
Automatic transmission (clutch, brake or gear, etc.) |
Comes on | DTC stored |
The TCM calculates the amount of heat absorbed by the friction material based on the difference in revolution (clutch slippage) between the turbine and output shaft. The TCM turns on the MIL and stores this DTC when the amount of heat absorption exceeds the specified value.
There are two reasons that make the revolution different.
When the shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.
When the shift solenoid valve remains on or off, the gear position commanded by the TCM and the actual gear position are not the same.
If you continue driving under these conditions, the clutch will burn out and the vehicle will no longer be drivable.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / DTC.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| P0894 and/or P2714 is output | A |
| P0894, P2714 and other DTCs are output | B |
If any other codes besides P0894 and P2714 are output, perform troubleshooting for those DTCs first.
A
B
Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
Be careful to prevent the hose of SST from interfering with the exhaust pipe.
Perform the test with the A/C off.
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Remove the test plug from the transmission case and connect SST.
Connect the GTS to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the GTS, perform the Active Test.
Measure the line pressure.
| Tester Display |
|---|
| Activate the Solenoid (SLT) |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Activate the Solenoid (SLT) | Operate shift solenoid valve SLT and raise line pressure | ON or OFF
|
[Vehicle Condition]
·
Vehicle stopped ·
Engine idling |
Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Drivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)>HYDRAULIC TEST) as well. Note that the pressure values in the Active Test and hydraulic test are different.
The line pressure changes as specified when performing the Active Test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
This test should always be performed with at least 2 people.
Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
Perform the test with the A/C turned off.
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Clear the DTC.
Warm up the engine.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the GTS, perform the Active Test.
While driving, the shift position can be forcibly changed with the GTS.
| Active Test Display |
|---|
| Control the Shift Position |
| Data List Display |
|---|
| Shift Status |
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate shift solenoid valves and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Possible to check operation of the shift solenoid valves.
[Vehicle Condition] 50 km/h (31 mph) or less |
This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
The 4th to 5th up-shift must be performed with the accelerator pedal released.
The 5th to 4th down-shift must be performed with the accelerator pedal released.
Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
The shift position commanded by the TCM is shown in the Data List display on the GTS.
Compare the TCM gear shift command and the actual gear position.
Gear position changes in accordance with the GTS command.
| System Condition | TCM Gear Shift Command | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | ||||
| Malfunction | Shift solenoid valve S1 | Stuck ON | 1st | 2nd | 2nd | 1st | N*1 | A |
| Stuck OFF | 4th | 3rd | 3rd | 4th | 5th | |||
| Shift solenoid valve S2 | Stuck ON*2 | 2nd | 2nd | 3rd | 3rd | N*1 | B | |
| Stuck OFF*3 | 1st | 1st | 4th | 4th | 5th | |||
| Shift solenoid valve SL2 | Stuck ON | 1st | 2nd | 3rd | 4th | N*1 | C | |
| Stuck OFF | 1st | 2nd | 3rd | 4th | 5th | |||
| Shift solenoid valve SR | Stuck ON*4 | 1st | 2nd | 3rd | 4th | 5th | D | |
| Stuck OFF*5 | 1st | 2nd | 3rd | 4th | 4th | |||
| Normal | 1st | 2nd | 3rd | 4th | 5th | E | ||
*1: Neutral
*2: When shift solenoid valve S2 is stuck ON, the vehicle cannot drive in reverse.
*3: When shift solenoid valve S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also, the 5th to 4th down-shift will have time lag.
*4: When shift solenoid valve SR is stuck ON, the condition can be determined by checking if shift shock has increased excessively.
*5: When shift solenoid valve SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
Gear shift can be determined by paying attention to changes in engine speed.
A
B
C
D
E
| *a | Component without harness connected
(Shift Solenoid Valve S1) |
Remove shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve S1 connector ·
Battery negative (-) → Shift solenoid valve S1 body |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the torque converter assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Solenoid Valve S2) |
Remove shift solenoid valve S2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve S2 connector ·
Battery negative (-) → Shift solenoid valve S2 body |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the torque converter assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Solenoid Valve SL2) |
Remove shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the torque converter assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Solenoid Valve SL1) |
Remove shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Solenoid Valve SR) |
Remove shift solenoid valve SR.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Shift solenoid valve SR connector terminal - Shift solenoid valve SR body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) → Shift solenoid valve SR connector ·
Battery negative (-) → Shift solenoid valve SR body |
Valve moves and makes operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the torque converter assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Shift Solenoid Valve SLT) |
Remove shift solenoid valve SLT.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 2 ·
Battery negative (-) → Terminal 1 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the torque converter assembly.
Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION
The torque converter assembly operates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG