Home › Drivetrain › A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) › from 2014.10
RM1840EF _52 Drivetrain _009612 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0052493 AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART) C

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1KD-FTV with i-ART)  P2757  Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU)  


DESCRIPTION

The TCM uses the signals from the throttle position sensor, air-flow meter, turbine (input) speed sensor, output speed sensor and crankshaft position sensor to monitor the engagement condition of the lock-up clutch.

C261110E05
4.74,2.052 5.052,1.146 5.052,1.146 5.115,1.146 true 4.948,2.219 5.083,2.625 5.083,2.625 5.156,2.625 true 5.729,2.313 5.833,2.625 5.833,2.625 5.896,2.625 true 5.948,2.542 6.833,2.76 0.885,0.219 10 false Solenoid Coil 0.042,0.552 1.292,0.771 1.25,0.219 10 false Hydraulic Pressure 2.521,2.938 3.083,3.156 0.563,0.219 10 false Current 5.198,2.531 5.729,2.75 0.531,0.219 10 false Sleeve 5.167,1.052 6,1.271 0.833,0.219 10 false Spool Valve

Then the TCM compares the engagement condition of the lock-up clutch with the lock-up schedule in the TCM memory to detect mechanical problems of shift solenoid valve SLU, the valve body and torque converter assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P2757 Torque Converter Clutch Pressure Control Solenoid Performance (Shift Solenoid Valve SLU) Lock-up does not occur when driving in the lock-up range (normal driving at 80 km/h (50 mph)), or lock-up remains ON in the lock-up OFF range (2-trip detection logic).
·

Shift solenoid valve SLU remains open or closed

·

Valve body is blocked

·

Torque converter assembly

·

Automatic transmission (clutch, brake, gear, etc.)

·

Line pressure is too low


Comes on DTC stored

MONITOR DESCRIPTION

Torque converter assembly lock-up is controlled by the TCM based on the turbine (input) speed sensor NT, output speed sensor SP2, engine speed, engine load, engine temperature, vehicle speed, transmission temperature and gear selection. The TCM determines the lock-up status of the torque converter assembly by comparing the engine speed (NE) to the input turbine speed (NT). The TCM calculates the actual transmission gear by comparing the input turbine speed (NT) to the output shaft speed (SP2). When conditions are appropriate, the TCM requests lock-up by applying control voltage to shift solenoid SLU. When shift solenoid valve SLU is turned on, it applies pressure to the lock-up relay valve and locks the torque converter assembly.

If the TCM detects no lock-up after lock-up has been requested or if it detects lock-up when it is not requested, the TCM interprets this as a fault in shift solenoid valve SLU or the lock-up system performance.

The TCM will turn on the MIL and store the DTC.

Example:

When either of the following is met, the system judges it as a malfunction.

·

There is a difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter assembly when the TCM commands lock-up on (the engine speed is at least 70 rpm more than the input turbine speed).

·

There is no difference in speed between the input side (engine speed) and output side (input turbine speed) of the torque converter assembly when the TCM commands lock-up off (the difference between the engine speed and input turbine speed is less than 35 rpm).


CAUTION / NOTICE / HINT

ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Active Test.


g.

According to the display on the GTS, perform the Active Test.

Powertrain > ECT > Active Test
Tester Display
Activate the Lock Up
50004 64 115
Powertrain > ECT > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Activate the Lock Up Control shift solenoid valve SLU to set automatic transmission to lock-up ON or OFF Possible to check shift solenoid valve SLU operation.
[Vehicle Condition]
·

Throttle valve opening angle: Less than 35%

·

Vehicle speed: 60 km/h (37 mph) or more


HINT:
·

This test can be conducted when the vehicle speed is 60 km/h (37 mph) or more.

·

This test can be conducted with the 5th gear.




h.

Lightly depress the accelerator pedal and check that the engine speed does not change abruptly.

C159073E01
4.531,2.188 5.51,1.958 5.51,1.958 5.573,1.958 false 5.198,2.229 5.542,2.615 5.542,2.615 5.604,2.615 false 0.719,2.677 1.677,2.948 0.958,0.271 10 false Engine Speed 0.719,1.677 1.813,2.156 1.094,0.479 10 false Accelerator Pedal Fully Released 0.719,1.021 1.823,1.542 1.104,0.521 10 false Accelerator Pedal Opening Angle 4.99,3.125 5.438,3.323 0.448,0.198 10 false Time 5.656,1.865 6.615,2.146 0.958,0.281 10 false Lock-up OFF 5.656,2.49 6.646,2.708 0.99,0.219 10 false Lock-up ON

HINT:
·

When changing the accelerator pedal opening angle while driving, if the engine speed does not change, lock-up is on.

·

Slowly release the accelerator pedal in order to decelerate, but do not fully release the pedal.

(Fully releasing the pedal will close the throttle valve and lock-up may be turned off automatically.)





PROCEDURE

1.CHECK DTC OUTPUT (IN ADDITION TO DTC P2757)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / ECT / DTC.

Powertrain > ECT > Trouble Codes
50001 64

e.

Read the DTCs using the GTS.

Result:
Result Proceed to
Only P2757 is output A
P2757 and other DTCs are output B


HINT:

If any other codes besides P2757 are output, perform troubleshooting for those DTCs first.




A

2.INSPECT SHIFT SOLENOID VALVE SLU

B

2.INSPECT SHIFT SOLENOID VALVE SLU
a.
C209928C37
1.771,0.969 2.208,0.365 true 1.469,0.979 1.052,0.365 true 1.771,2.958 2.208,2.354 true 1.469,2.948 1.052,2.354 true 0.052,0.042 0.365,0.24 0.313,0.198 10 false *a 2.24,0.198 2.406,0.396 0.167,0.198 10 false 1 0.917,0.198 1.083,0.396 0.167,0.198 10 false 2 2.24,2.188 2.406,2.385 0.167,0.198 10 false 1 0.917,2.188 1.083,2.385 0.167,0.198 10 false 2 1.927,3.927 2.125,4.125 0.198,0.198 10 false (-) 1.115,3.927 1.333,4.125 0.219,0.198 10 false (+)
*a Component without harness connected
(Shift Solenoid Valve SLU)


Remove shift solenoid valve SLU.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 5.0 to 5.6 Ω



c.

Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

OK:
Measurement Condition Specified Condition
·

Battery positive (+) with a 21 W bulb → Terminal 2

·

Battery negative (-) → Terminal 1


Valve moves and makes an operating noise



Result:
Proceed to
OK
NG



OK

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY

NG

3.INSPECT TRANSMISSION VALVE BODY ASSEMBLY
a.

Check the transmission valve body assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY

OK:

There are no foreign objects on any valve.



Result:
Proceed to
OK
NG



OK

4.INSPECT TORQUE CONVERTER ASSEMBLY

NG

REPAIR OR REPLACE TRANSMISSION VALVE BODY ASSEMBLY

4.INSPECT TORQUE CONVERTER ASSEMBLY
a.

Check the torque converter assembly.

Click hereDrivetrain>A750F AUTOMATIC TRANSMISSION / TRANSAXLE>TORQUE CONVERTER AND DRIVE PLATE>INSPECTION

OK:

The torque converter assembly operates normally.



Result:
Proceed to
OK
NG



OK

NG