ECD SYSTEM (for i-ART) > White Smoke Emitted |
| Faults and Symptoms of Common Rail Diesel Components |
Engine Control
| Main fault | Turbocharger (compressor side seal ring, turbine side seal ring, shaft, oil drain) | |
| Symptoms | White smoke Excessive oil consumption | |
| Main fault | Glow system malfunction | |
| Symptoms | Difficult to start, rough idle, knocking, white smoke (when cold) | |
| Data List | Check the glow plug indicator light | |
| Diagnostic Point | Measure the resistance of the glow plug | |
| Main fault | Loss of compression | |
| Symptoms | Rough idle (constant lack of power) | |
| Data List | Engine Speed of Cyl #1 to #4
| |
Diesel Injection
| Main fault | Blockage | |
| Symptoms | Rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Injection Feedback Val #1 to #4
| |
| Main fault | Circuit fault: The injector assembly does not open. | |
| Symptoms | Difficult to start, rough idle, lack of power, black smoke, white smoke, knocking | |
| Data List | Same as injector assembly | |
| Diagnostic Trouble Code | When the injector driver has a fault, some DTCs may be stored. | |
| Main fault | - | |
| Symptoms | Difficult to start, rough idle (especially when cold) | |
Diesel EGR
| Main fault |
|
| Symptoms |
|
| Data List | Actual EGR Valve Pos., Target EGR Position
|
| Explanation of Symptom |
| White Smoke | When the engine is misfiring, any fuel that has been injected but remains unburned is emitted as white smoke. |
| Turbocharger internal oil leak (Click here) If oil leak occurs from turbine side seal, large amount of white smoke will be emitted from exhaust pipe. Internal oil leak is not visible from outside of turbocharger. |
| 1.CONFIRM CONDITIONS PRESENT WHEN WHITE SMOKE APPEARED WITH CUSTOMER |
Ask the customer about the conditions when the white smoke was emitted.
- What were the driving conditions when the white smoke was generated.
- Is the white smoke constantly emitted, or only occasionally?
- Does the white smoke occur only when the vehicle is cold, or when the vehicle is both cold and hot?
- Is the white smoke emitted just after starting the vehicle only, or does it continue while the vehicle is idling?
Determine the symptoms of the problem to narrow down the possible causes.
| NEXT | |
| 2.READ OUTPUT DTC (RELATING TO ENGINE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read pending DTCs.
| Result | Proceed to |
| No DTCs are output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 3.CHECK WHEN WHITE SMOKE IS EMITTED |
![]() |
Start the engine.
Fully depress the accelerator pedal, and then release it.
Check whether white smoke is emitted or not when racing the engine.
| *a | Example |
| Result | Proceed to |
| White smoke is emitted just after engine start only | A |
| White smoke is always and continuously emitted | B |
There is oil on the exhaust pipe, etc.
| C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK TEMPERATURE WHEN WHITE SMOKE IS EMITTED |
Check whether the white smoke is emitted only when the engine coolant temperature is below 0°C (32°F).
| Result | Proceed to |
| White smoke is emitted when the temperature is below 0°C (32°F) | A |
| White smoke is emitted regardless of temperature | B |
|
| ||||
| A | |
| 5.INSPECT GLOW PLUG (RESISTANCE) |
Inspect the glow plug .
|
| ||||
| OK | |
| 6.READ VALUE USING GTS |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / Fuel Press, Target Common Rail Pressure.
Take a snapshot with the GTS.
Measure the difference between the target fuel pressure (Target Common Rail Pressure) and the actual fuel pressure (Fuel Press) when racing the engine with the accelerator pedal fully depressed.
| Result | Proceed to |
| Fuel pressure is within 5000 kPa of Target Common Rail Pressure | A |
| Except above | B |
|
| ||||
| A | |
| 7.READ VALUE USING GTS (INJECTION FEEDBACK VAL #1 TO #4, INJECTION VOLUME) |
Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken after the engine is warmed up and idled for 1 minute with the A/C off.
| Result | Proceed to |
| Injection Feedback Val #1 to #4 are 3 mm3/st or less and Injection Volume is 4.5 to 10 mm3/st | A |
| Other than above | B |
|
| ||||
| B | |
| 8.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.
| NEXT | |
| 9.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Crank the engine.
Check the engine speed during the Active Test.
| Result | Proceed to |
| The values of Engine Speed Cyl #1 to #4 are within 10 rpm of each other | A |
| Other than above | B |
|
| ||||
| B | |
| 10.CHECK CYLINDER COMPRESSION PRESSURE OF MALFUNCTIONING CYLINDER |
Check cylinder compression pressure .
|
| ||||
| OK | |
| 11.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine.
Enter the following menus: Powertrain / Engine / Data List / Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
| NEXT | |
| 12.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly (Click here).
| NEXT | |
| 13.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 14.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the white smoke problem has been successfully repaired by starting the engine.
|
| ||||
| NG | |
| 16.CHECK FUEL QUALITY |
Check that only diesel fuel is being used.
Check that the fuel does not contain any impurities.
| NEXT | ||
| ||
| 17.CHECK IF FUEL IS BEING SUPPLIED TO FUEL SUPPLY PUMP ASSEMBLY |
Disconnect the inlet hose from the fuel supply pump assembly.
Operate the priming pump and check that fuel is being supplied to the fuel supply pump assembly.
Reconnect the inlet hose.
| NEXT | |
| 18.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 19.CHECK AND REPLACE CLOGGED FUEL PIPE (INCLUDING FROZEN FUEL) (FUEL TANK - FUEL SUPPLY PUMP) |
Check and replace the clogged fuel pipe.
| NEXT | |
| 20.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the white smoke problem has been successfully repaired by starting the engine.
| NEXT | ||
| ||
| 22.READ VALUE USING GTS (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
| Result | Proceed to |
| The value for Injector Leaking Count #1 to #4 does not change from 0 The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip | A |
| The value for Injector Leaking Count #1 to #4 displays 1 or more The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more | B |
|
| ||||
| A | |
| 23.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE EGR VALVE CLOSE) |
Connect the GTS to the DLC3.
Start the engine and warm it up, and make sure the A/C switch and all accessory switches are off.
Turn the ignition switch off. Wait for 30 seconds, and then restart the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAF.
Read the MAF value displayed on the GTS while the engine is idling.
Enter the following menus: Powertrain / Engine / Active Test / Activate the EGR Valve Close.
Read the MAF value when the EGR valve is closed using the Active Test function.
| Active Test | Result | Proceed to |
| Activate the EGR Valve Close: Off (Open) to On (Closed) | MAF value does not change | A |
| MAF value changes | B |
| EGR Valve Condition (Opening) | Measuring Condition | MAF (Reference) |
| Open (55%) |
| 3 to 10 gm/s |
| Closed (0%) | 12 to 21 gm/s |
|
| ||||
| B | |
| 24.CHECK ENGINE ASSEMBLY |
Inspect the engine to see whether white smoke is being emitted due to defects in the engine itself.
Check for oil leaking into the combustion chamber due to a faulty valve stem oil seal.
Check for oil leaking into the combustion chamber due to a faulty injector assembly nozzle sheet.
Check for low compression.
| NEXT | ||
| ||
| 25.CHECK IDLING CONDITION |
Start the engine.
Check the idling condition.
| Result | Proceed to |
| Engine runs smoothly at idle, however white smoke is emitted. | A |
There are problems such as rough idling or engine stall, and white smoke is emitted.
| B |
|
| ||||
| A | ||
| ||
| 26.CHECK FOR OIL LEAKAGE |
Remove any oil in the front exhaust pipe assembly.
If there is an oil leak, repair the leak.
| NEXT | ||
| ||
| 27.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly (Click here).
| NEXT | |
| 28.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 29.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 30.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the white smoke problem has been successfully repaired by starting the engine.
| NEXT | ||
| ||