DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0420 | OSC value is less than the standard value under active air-fuel ratio control (2 trip detection logic). |
|

| *1 | Exhaust Manifold | *2 | Air Fuel Ratio Sensor |
| *3 | TWC: Front Catalyst | *4 | TWC: Rear Catalyst |
| *5 | Front Exhaust Pipe Assembly | *6 | Heated Oxygen Sensor |
| *7 | Center Exhaust Pipe Assembly | *8 | Tailpipe Assembly |
| Required Sensors/Components (Main) | Air fuel ratio sensor, heated oxygen sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Battery voltage | 11 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Atmospheric pressure | 76 kPa (570 mmHg) or higher |
| Idling | OFF |
| Engine speed | Less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 80% |
| All of following conditions (a), (b) and (c) met | - |
| (a) Mass air flow | 2.5 to 33 gm/s |
| (b) Estimated front catalyst temperature | 660 to 800°C (1220 to 1472°F) (Automatic Transaxle Models) 685 to 800°C (1220 to 1472°F) (Manual Transaxle Models) |
| (c) Estimated rear catalyst temperature | 400 to 760°C (752 to 1400°F) |
| Transmission gear | 4th or higher |


| Engine Speed | 3000 rpm (without load) | 2000 rpm (during fuel-cut) | 2000 rpm (revving up the engine) |
| AFS Voltage B1S1 | 3.263 to 3.302 V | 4.996 V | 3.195 V |
| O2S B1S2 | 0.820 to 0.835 V | 0.015 V | 0.820 V |

| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0420 is output | A |
| P0420 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the intelligent tester on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling.
Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.
| Intelligent Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | +12.5% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio) | -12.5% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen) | +12.5% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen) | -12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Lean/Rich | Lean | Heated oxygen sensor malfunction |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction |
| C |
| Lean | Lean | Actual air fuel ratio lean |
| D |
| Rich | Rich | Actual air fuel ratio rich |
| D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.
|
| ||||
| OK | |
| 4.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST) |
Replace the front exhaust pipe assembly (Click here).
| NEXT | ||
| ||
| 5.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
|
| ||||
| 6.CHECK FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.
|
| ||||
| OK | |
| 7.REPLACE HEATED OXYGEN SENSOR |
Replace the heated oxygen sensor (Click here).
|
| ||||
| 8.CHECK FOR EXHAUST GAS LEAK |
Inspect for exhaust gas leaks from the exhaust manifold and exhaust pipes.
|
| ||||
| OK | |
| 9.CHECK CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO |
Check the cause of the extremely rich or lean actual air fuel ratio while referring to the DTC P0171 Inspection Procedure .
| NEXT | |
| 10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0420) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| P0420 is output | A |
| No DTC is output | B |
|
| ||||
| A | |
| 11.REPLACE FRONT EXHAUST PIPE ASSEMBLY (TWC: FRONT AND REAR CATALYST) |
Replace the front exhaust pipe assembly (Click here).
| NEXT | ||
| ||