ECD SYSTEM (w/o EGR Cooler) > Engine Knocking or Rattling |
| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|
|
|
| 1.CHECK SOUND AREA |
Find the source of the abnormal sound using a mechanic's stethoscope.
| Result | Proceed to |
| Combustion noise from engine | A |
| Noise from specific part | B |
|
| ||||
| A | |
| 2.READ OUTPUT DTCS (RELATING TO ENGINE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| No output | A |
| Engine related DTCs | B |
|
| ||||
| A | |
| 3.CHECK INJECTOR COMPENSATION CODE |
Check the injector compensation code .
|
| ||||
| OK | |
| 4.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.
| NEXT | |
| 5.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME) |
Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken when the engine was idling and at 4000 rpm with no load.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | A |
| Injection Volume is 10 mm3/st or less at 4000 rpm | B |
| Except above | C |
|
| ||||
|
| ||||
| C | |
| 6.CHECK SNAPSHOT (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was warmed up and idling.
|
| ||||
| OK | |
| 7.CHECK THE TEMPERATURE WHEN KNOCKING OCCURS |
Check the temperature when knocking trouble occurs.
| Result | Proceed to |
| Knocking occurs only in cold engine | A |
| Knocking occurs both in cold and warmed up engine | B |
|
| ||||
| A | |
| 8.INSPECT GLOW PLUG (RESISTANCE) |
Inspect the glow plug .
|
| ||||
| OK | |
| 9.TAKE SNAPSHOT DURING IDLING (WHEN ENGINE COLD) |
Make sure that the engine is cold so that the snapshot can be taken under the correct conditions.
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data.
Take a snapshot of the following Data List items.
| NEXT | |
| 10.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #4) |
Check Injection Feedback Val #1 to #4 in the snapshot taken when the engine was idling.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | A |
| Except above | B |
|
| ||||
|
| ||||
| 11.REPLACE FUEL INJECTORS OF ALL CYLINDERS |
Replace the fuel injectors (Click here).
|
| ||||
| 12.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CHECK THE CYLINDER COMPRESSION) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
| Result | Proceed to |
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. | B |
|
| ||||
| A | |
| 13.CHECK CYLINDER COMPRESSION PRESSURE |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 14.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
| NEXT | |
| 15.CLEAN OR REPLACE FUEL FILTER |
Clean the interior of the fuel filter case.
If the fuel filter is obviously dirty or clogged, replace the fuel filter.
| NEXT | |
| 16.REGISTER INJECTOR COMPENSATION CODE AND PERFORM PILOT QUANTITY LEARNING |
Register the injector compensation codes .
Perform the fuel injector pilot quantity learning .
| NEXT | |
| 17.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 18.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the knocking has been successfully repaired.
| NEXT | ||
| ||
| 19.REPLACE FUEL SUPPLY PUMP |
Replace the fuel supply pump (Click here).
| NEXT | |
| 20.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 21.PERFORM FUEL SUPPLY PUMP INITIALIZATION |
Perform fuel supply pump initialization (Click here).
| NEXT | |
| 22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the knocking has been successfully repaired by starting the engine.
| NEXT | ||
| ||
| 23.READ VALUE USING INTELLIGENT TESTER (MAP AND ATMOSPHERE PRESSURE) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).
| Result | Proceed to |
| MAP and Atmosphere Pressure have same value | A |
| MAP is different from actual atmospheric pressure | B |
| Atmosphere Pressure is different from actual atmospheric pressure | C |
|
| ||||
|
| ||||
| A | |
| 24.CHECK FOR CAUSE OF FAILURE |
| NEXT | ||
| ||