FUEL INJECTOR (w/o Glow Plug Controller) > REMOVAL |
| 1. PRECAUTION |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
| 3. DRAIN ENGINE COOLANT (w/ EGR Cooler) |
| 4. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler) |
| 5. REMOVE INTERCOOLER ASSEMBLY (w/o EGR Cooler) |
| 6. CHECK FOR INJECTOR COMPENSATION CODE |
Read the injector compensation code.
Check that compensation code of installed injector is same as code registered in ECM. If the code is not as specified, register the injector compensation code on the injector.
| 7. DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler) |
![]() |
Remove the clamp.
Disconnect the No. 3 water by-pass hose from the EGR cooler.
| 8. DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler) |
Disconnect the No. 4 water by-pass hose from the EGR cooler.
| 9. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the 2 nuts and No. 3 injection pipe clamp.
![]() |
Remove the 2 bolts and 2 No. 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
w/o EGR Cooler:
![]() |
Remove the bolt and No. 2 injection pipe clamp.
Remove the 2 nuts and No. 3 injection pipe clamp.
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
| 10. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler) |
![]() |
Remove the 3 bolts and No. 2 intake air connector bracket.
| 11. DISCONNECT NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler) |
![]() |
Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.
| 12. REMOVE NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler) |
![]() |
Disconnect the 2 vacuum hoses.
Remove the bolt and No. 1 gas filter with gas filter bracket.
| 13. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler) |
w/ EGR Cooler:
![]() |
Disconnect the connector.
![]() |
Disconnect the 4 vacuum hoses.
![]() |
Remove the 2 bolts and electric vacuum regulating valve with bracket.
w/o EGR Cooler:
![]() |
Disconnect the 2 connectors.
Disconnect the 3 vacuum hoses.
Remove the 2 bolts and electric vacuum regulating valve together with the bracket.
![]() |
Remove the screw and vacuum switching valve.
| 14. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Remove the 3 nuts, No. 2 intake air connector and gasket.
| 15. REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler) |
![]() |
Remove the 3 bolts, intake air connector and 2 gaskets.
| 16. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler) |
Disconnect the EGR valve position sensor connector.
![]() |
Disconnect the vacuum hose from the No. 2 EGR valve.
![]() |
Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.
Remove the gasket from the cylinder head.
| 17. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY |
w/ EGR Cooler:
![]() |
Remove the bolt and disconnect the injection pipe clamp.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
w/o EGR Cooler:
![]() |
Remove the 2 bolts and disconnect the 2 injection pipe clamps.
![]() |
Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.
| 18. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY |
Disconnect the 3 fuel hoses.
![]() |
Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.
| 19. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 3 bolts and disconnect the 4 connectors.
Disconnect the ventilation hose.
![]() |
Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.
![]() |
Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.
![]() |
Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.
| 20. REMOVE INJECTOR ASSEMBLY |
![]() |
Remove the union bolt, 4 injector hollow screws, 5 gaskets and nozzle leakage pipe.
![]() |
Remove the 4 bolts, 4 washers, 4 No. 1 nozzle holder clamps and 4 injectors.
Remove the O-ring from each injector.
Remove the 4 injection nozzle seats from the cylinder head.