ECD SYSTEM (for i-ART) > Engine Knocking or Rattling |
| Malfunction Condition | Main Trouble Area | Related Trouble Area |
|
|
|
| 1.CHECK SOUND AREA |
Find the source of the abnormal sound using a mechanic's stethoscope.
| Result | Proceed to |
| Combustion noise from engine | A |
| Noise from specific part | B |
|
| ||||
| A | |
| 2.READ OUTPUT DTCS (RELATING TO ENGINE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| No DTC is output | A |
| Engine related DTCs are output | B |
|
| ||||
| A | |
| 3.TAKE SNAPSHOT DURING IDLING AND 4000 RPM (AFTER ENGINE WARMED UP) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Take a snapshot of the following Data List items.
| NEXT | |
| 4.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #4 AND INJECTION VOLUME) |
Check Injection Feedback Val #1 to #4 and Injection Volume in the snapshot taken when the engine was idling and at 4000 rpm with no load.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | A |
| Injection Volume is 10 mm3/st or less at 4000 rpm | B |
| Except above | C |
|
| ||||
|
| ||||
| C | |
| 5.CHECK SNAPSHOT (FUEL PRESS AND TARGET COMMON RAIL PRESSURE) |
Check Fuel Press and Target Common Rail Pressure in the snapshot taken when the engine was warmed up and idling.
|
| ||||
| OK | |
| 6.CHECK THE TEMPERATURE WHEN KNOCKING OCCURS |
Check the temperature when knocking trouble occurs.
| Result | Proceed to |
| Knocking occurs only in cold engine | A |
| Knocking occurs both in cold and warmed up engine | B |
|
| ||||
| A | |
| 7.INSPECT GLOW PLUG (RESISTANCE) |
Inspect the glow plug .
|
| ||||
| OK | |
| 8.TAKE SNAPSHOT DURING IDLING (WHEN ENGINE COLD) |
Make sure that the engine is cold so that the snapshot can be taken under the correct conditions.
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data.
Take a snapshot of the following Data List items.
| NEXT | |
| 9.CHECK SNAPSHOT (INJECTION FEEDBACK VAL #1 TO #4) |
Check Injection Feedback Val #1 to #4 in the snapshot taken when the engine was idling.
| Result | Proceed to |
| Injection Feedback Val for at least one cylinder is more than +3 mm3/st | A |
| Except above | B |
|
| ||||
|
| ||||
| 10.REPLACE INJECTOR ASSEMBLIES OF ALL CYLINDERS |
Replace the injector assemblies (Click here).
|
| ||||
| 11.PERFORM ACTIVE TEST USING GTS (CHECK THE CYLINDER COMPRESSION) |
Connect the GTS to the DLC3.
Start the engine and turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Check the Cylinder Compression / Data List / Compression / Engine Speed of Cyl #1 to #4.
Check the engine speed during the Active Test.
| Result | Proceed to |
| Except below | A |
| The values of Engine Speed Cyl #1 to #4 are within +/-10 rpm of each other. | B |
|
| ||||
| A | |
| 12.CHECK CYLINDER COMPRESSION PRESSURE |
Check the cylinder compression pressure .
|
| ||||
| OK | |
| 13.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm.
Record the value displayed for Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4.
| NEXT | |
| 14.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
| NEXT | |
| 15.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER |
Clean the fuel filter case and replace the fuel filter.
| NEXT | |
| 16.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 17.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the knocking has been successfully repaired.
| NEXT | ||
| ||
| 18.REPLACE FUEL SUPPLY PUMP ASSEMBLY (SUCTION CONTROL VALVE) |
Replace the fuel supply pump assembly (Click here).
| NEXT | |
| 19.BLEED AIR FROM FUEL SYSTEM |
Bleed the air from the fuel system .
| NEXT | |
| 20.PERFORM SUPPLY PUMP INITIALIZATION |
Perform supply pump initialization (Click here).
| NEXT | |
| 21.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check whether the knocking has been successfully repaired by starting the engine.
| NEXT | ||
| ||
| 22.CHECK SNAPSHOT (INJECTOR LEAKING COUNT #1 TO #4, I-ART LEARNING STATUS HISTORY #1 TO #4) |
Check Injector Leaking Count #1 to #4 and i-ART Learning Status History #1 to #4 in the snapshot taken in procedure 3 when the engine was idling and at 4000 rpm.
| Result | Proceed to |
| The value for Injector Leaking Count #1 to #4 does not change from 0 The value for i-ART Learning Status History #1 to #4 does not change from 0 Trip | A |
| The value for Injector Leaking Count #1 to #4 displays 1 or more The value for i-ART Learning Status History #1 to #4 displays 1 Trip or more | B |
|
| ||||
| B | |
| 23.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER |
Replace the injector assembly of the malfunctioning cylinder (Click here).
|
| ||||
| 24.READ VALUE USING GTS (MAP AND ATMOSPHERE PRESSURE) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAP and Atmosphere Pressure.
Compare MAP to Atmosphere Pressure when the ignition switch is ON (do not start the engine).
| Result | Proceed to |
| MAP and Atmosphere Pressure have same value | A |
| MAP is different from actual atmospheric pressure | B |
| Atmosphere Pressure is different from actual atmospheric pressure | C |
|
| ||||
|
| ||||
| A | |
| 25.BASIC INSPECTION |
Check the fuel quality.
Check the fuel for air.
Check the fuel system for blockages.
Check the air filter.
Check the engine oil.
Check the engine coolant.
Check the engine idling speed and maximum engine speed.
Check the vacuum pump.
| NEXT | ||
| ||