DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
DTC P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 P2A03 | Calculated test value for A/F sensor response rate deterioration level is less than threshold |
|

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| UNKNOWN |
|
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +12% | Rich | Less than 3.1 V |
| AFS B1S1 or AFS B2S1 (A/F) | -12% | Lean | More than 3.4 V |
| O2S B1S2 or O2S B2S2 (heated oxygen sensor) | +12% | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (heated oxygen sensor) | -12% | Lean | Less than 0.4 V |
| Case | Air Fuel Ratio Sensor (Sensor 1) Output Voltage | Heated Oxygen Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read DTCs.
| Result | Proceed to |
| P2A00 and/or P2A03 is output | A |
| P2A00 and/or P2A03 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (INJECTION VOLUME) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the tester.
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | -12% | Lean | Higher than 3.4 V |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | -12% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean/Rich | Lean/Rich | Normal | A |
| Lean | Lean | Actual air fuel ratio lean | B |
| Rich | Rich | Actual air fuel ratio rich | B |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | C |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | C |
Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).
|
| ||||
|
| ||||
| A | |
| 3.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2A00 or P2A03 is output) | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the A35 and A36 A/F sensor connectors.
Measure the resistance of the A/F sensor.
| Tester Connection | Condition | Specified Condition |
| 1 (HA1A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA1A) - 4 (A1A-) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 1 (HA2A) - 2 (+B) | 20°C (68°F) | 1.8 to 3.4 Ω |
| 1 (HA2A) - 4 (A2A-) | - | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK AIR INDUCTION SYSTEM |
Check the air induction system.
|
| ||||
| OK | |
| 6.CHECK FUEL PRESSURE |
Check the fuel pressure.
|
| ||||
| OK | |
| 7.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly.
|
| ||||
| OK | |
| 8.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor.
| NEXT | |
| 9.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2A00 or P2A03 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 10.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 11.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Check that the DTC judgment result is NORMAL.
| NEXT | ||
| ||
| 12.INSPECT FUEL PUMP |
Inspect the fuel pump .
|
| ||||
| OK | ||
| ||