Home › ENGINE · 2TR-FBE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0171    System Too Lean (Bank 1)

DTC    P0172    System Too Rich (Bank 1)

for Preparation Click here


DESCRIPTION

This FFV can be used with E22 to E100; E100 is a fuel with an ethanol concentration of 100%.
The short-term fuel trim is fuel compensation information that is used to constantly maintain the air fuel ratio at stoichiometric levels. The signal from the air fuel ratio sensor (sensor 1) indicates whether the air fuel ratio is rich or lean compared to the stoichiometric ratio. This triggers a reduction in the fuel injection volume if the air fuel ratio is rich and an increase in the fuel injection volume if lean. The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim consists of both the short-term (Short FT) and long-term (Long FT) fuel trims, and the alcohol concentration learned value (Alcohol Feedback Value).
Factors such as individual engine differences, wear over time and changes in operating environment cause short-term fuel trim to vary from the central value. The long-term fuel trim, which controls overall fuel compensation, compensates for long-term deviations in the fuel trim from the central value caused by the short-term fuel trim compensation. The alcohol concentration learned value (Alcohol Feedback Value) is the injection compensation amount, which the ECM calculates depending on the concentration of alcohol in the fuel. However, in addition to the concentration of alcohol in the fuel, the actual air-fuel ratio deviation due to malfunctions in the engine system is factored into the alcohol concentration learned value.
The fuel injection compensation amount, which is used to determine if DTCs P0171 and P0172 are stored, can be calculated by using the following formula.
Aggregate fuel trim is equal to the following: Short FT + ((1 + Long FT / 100) x (1 + Alcohol Feedback Value / 100) - 1) x 100

Alcohol Concentration
22% (E22)
46%
75%
100% (E100)
Alcohol Feedback Value
8%
24%
47%
70.5%
Example:
When E22 fuel is used: Aggregate fuel trim = Short FT + ((1 + Long FT / 100) x (1.08) - 1) x 100

DTC No.
DTC Detection Condition
Trouble Area
P0171
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2-trip detection logic).
  1. Air induction system
  2. Fuel pressure
  3. Fuel injector blockage
  4. Mass air flow meter
  5. Engine coolant temperature sensor
  6. Gas leakage from exhaust system
  7. Open or short in heated oxygen sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. Air fuel ratio sensor heater circuits
  11. PCV hose connections
  12. PCV valve and hose
  13. ECM
  14. Wire harness or connector
P0172
With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2-trip detection logic).
  1. Fuel injector leakage or blockage
  2. Fuel pressure
  3. Mass air flow meter
  4. Engine coolant temperature sensor
  5. Ignition system
  6. Gas leakage from exhaust system
  7. Open or short in heated oxygen sensor circuit
  8. Air fuel ratio sensor
  9. Air fuel ratio sensor heater
  10. Air fuel ratio sensor heater circuits
  11. Ignition system
  12. ECM
  13. Wire harness or connector

HINT:
  1. When DTC P0171 is stored, the actual air fuel ratio is too lean. When DTC P0172 is stored, the actual air fuel ratio is too rich.
  2. If the vehicle runs out of fuel, the air fuel ratio becomes lean and DTC P0171 may be stored. The MIL is then illuminated.
  3. When the aggregate fuel trim value is within the malfunction threshold values and the engine coolant temperature is higher than 75°C [167°F], the system is functioning normally.


MONITOR DESCRIPTION

During air-fuel ratio feedback, if the short-term fuel trim deviates from 1.0 by a large amount, the alcohol concentration learned value is updated (for example, if the short-term fuel trim is more than 1.0, the alcohol concentration learned value increases), and then the short-term fuel trim deviation is reflected in the long-term fuel trim.
Example:
When the aggregate fuel trim value is +130% or more, or -30% or less, the ECM interprets this as a fuel system malfunction and stores a DTC.

A197672E05


CONFIRMATION DRIVING PATTERN


A234241E04

  1. Connect the intelligent tester to the DLC3.
  2. Turn the ignition switch to ON and turn the tester on [A].
  3. Clear the DTCs (Click here).
  4. Start the engine and warm it up (until the engine coolant temperature is 75°C (167°F) or higher) with all the accessories switched off [B].
  5. With the engine warmed up, idle the engine for 2 minutes or more [C].
  6. Drive the vehicle at 60 km/h (37 mph) or more for 20 minutes or more [D].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. This step is performed to complete ethanol concentration learning.
    2. If DTC P0170 or P0172 is output when any of the following conditions is met, it is necessary to complete ethanol concentration learning to meet preconditions.
      1. The battery has been disconnected and reconnected.
      2. The DTCs have been cleared.
      3. Both fuel tank assemblies (for main and sub tanks) have been filled with fuel.

  7. Drive the vehicle at between 75 and 120 km/h (47 and 75 mph) and at an engine speed of between 1400 and 3200 rpm for 5 minutes or more [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  8. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
  9. Read the pending DTC [F].

    HINT:
    If a pending DTC is output, the system is malfunctioning.


WIRING DIAGRAM

Refer to DTC P2195 .

INSPECTION PROCEDURE

HINT:
  1. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  2. A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.
  3. A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.


Result 
Result
Proceed to
DTC P0171 or P0172 is output
A
DTC P0171 or P0172 and other DTCs are output
B

HINT:
If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

    OK:
    PCV hose is connected correctly and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE
OK


3.CHECK AIR INDUCTION SYSTEM
  1. Check the air induction system for vacuum leakage (Click here).

    OK:
    No leakage from air induction system.



NG
REPAIR OR REPLACE AIR INDUCTION SYSTEM
OK


4.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Turn the intelligent tester on.

  1. Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.

  1. Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the Air Fuel Ratio (A/F) sensor and the Heated Oxygen (HO2) sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the intelligent tester.

    HINT:
    1. The Control the Injection Volume for A/F Sensor operation lowers the fuel injection volume by -12.5% or increases the injection volume by +12.5%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Tester Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1
    (A/F)
    +12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2
    (HO2)
    +12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result 
    Status
    AFS B1S1
    Status
    O2S B1S2
    A/F Condition and
    A/F Sensor Condition
    Misfire
    Suspected Trouble Area
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    -
    A
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. PCV valve and hose
    2. PCV hose connections
    3. Injector blockage
    4. Gas leak from exhaust system
    5. Air induction system
    6. Fuel pressure
    7. Mass Air Flow (MAF) meter
    8. Engine Coolant Temperature (ECT) sensor
    A
    Rich
    Rich
    Actual air-fuel ratio rich
    -
    1. Injector leak or blockage
    2. Gas leak from exhaust system
    3. Ignition system
    4. Fuel pressure
    5. MAF meter
    6. ECT sensor
    Lean
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    B
    Rich
    Lean/Rich
    A/F sensor malfunction
    -
    1. A/F sensor
    Lean: During Control the Injection Volume for A/F Sensor, the A/F sensor output voltage (AFS) is consistently higher than 3.4 V, and the HO2 sensor output voltage (O2S) is consistently below 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor, the AFS is consistently below 3.1 V, and the O2S is consistently higher than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the heated oxygen sensor alternates correctly.

    HINT:
    Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (Click here).



B
Go to step 11
A


5.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Coolant Temp.

  1. Read Coolant Temp twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine: Same as ambient air temperature.
    With warm engine: Between 75°C and 100°C (167°F and 212°F).



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


6.READ VALUE USING INTELLIGENT TESTER (MAF)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.

  1. Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 10 gm/s and 11.5 gm/s (shift lever: N; A/C: Off).



G
Go to step 16
OK


7.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL SYSTEM
OK


8.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leakage.

    OK:
    No gas leakage.



NG
REPAIR OR REPLACE EXHAUST SYSTEM
OK


9.CHECK IGNITION SYSTEM
  1. Inspect the ignition system (Click here).



NG
REPAIR OR REPLACE IGNITION SYSTEM
OK


10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the fuel injection and volume (Click here).



OK
Go to step 15

NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)

11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
  1. Inspect the air fuel ratio sensor (Click here).



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


12.CHECK AIR FUEL RATIO SENSOR (POWER SOURCE)


    A100209E09
  1. Disconnect the air fuel ratio sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A5-2 (+B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Air Fuel Ratio Sensor)

  1. Reconnect the air fuel ratio sensor connector.



NG
Go to step 21
OK


13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A5-1 (HA1A) - E22-6 (HA1A)
    Always
    Below 1 Ω
    A5-3 (A1A+) - E22-7 (A1A+)
    Always
    Below 1 Ω
    A5-4 (A1A-) - E22-1 (A1A-)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A5-1 (HA1A) or E22-6 (HA1A) - Body ground
    Always
    10 kΩ or higher
    A5-3 (A1A+) or E22-7 (A1A+) - Body ground
    Always
    10 kΩ or higher
    A5-4 (A1A-) or E22-1 (A1A-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


15.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
END
A


16.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


17.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0171 or P0172 is output
    A
    DTC is not output
    B



B
END
A


18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A4-3 (VG) - E20-13 (VG)
    Always
    Below 1 Ω
    A4-2 (E2G) - E20-7 (E2G)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A4-3 (VG) or E20-13 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


19.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    If the result of the inspection performed in step 6 indicated no problem, proceed to the next step without replacing the mass air flow meter assembly.


NEXT


20.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0171 or P0172 is output
    B



B
REPLACE ECM (Click here)
A

END 

21.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY, A/F RELAY - INTEGRATION RELAY)
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the A/F relay from the engine room relay block.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    A5-2 (+B) - A/F relay terminal (3)
    Always
    Below 1 Ω
    A/F relay terminal (5) - 1H-1
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    A5-2 (+B) or A/F relay terminal (3) - Body ground
    Always
    10 kΩ or higher
    A/F relay terminal (5) or 1H-1 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the air fuel ratio sensor connector.

  1. Reinstall the integration relay.

  1. Reinstall the A/F relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.INSPECT AIR FUEL RATIO SENSOR HEATER RELAY (A/F)
B060778E19
  1. Inspect the A/F relay.

    1. Remove the A/F relay from the engine room relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      3 - 5
      Always
      10 kΩ or higher
      3 - 5
      Always
      Below 1 Ω
      (when battery voltage is applied to terminals 1 and 2)



NG
REPLACE AIR FUEL RATIO SENSOR HEATER RELAY (A/F)
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)