DTC C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction |
DTC C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1430 | Either condition is met:
|
|
| C1431 | Either condition is met:
|
| 1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond specified point OFF: Brake pedal not depressed beyond specified point | - |
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.
Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch are turned on.
| Result | Proceed to |
| OK | A |
| NG (Turning on of brake pedal load sensing switch is not confirmed) | B |
| NG (Brake pedal load sensing switch turns on first) | C |
|
| ||||
|
| ||||
| A | |
| 2.RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform a braking test (decelerate the vehicle by depressing the brake pedal).
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTC is not output | A |
| DTC is output | B |
|
| ||||
| A | ||
| ||
| 3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH |

| *1 | Brake Pedal Load Sensing Switch | *2 | Brake with Switch Pedal Sub-assembly |
| *a | Component without harness connected (Brake Pedal Load Sensing Switch) | *b | Brake Pedal Released (Closed) |
| *c | Brake Pedal Depressed (Open) | - | - |
Turn the ignition switch off.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 - 1 | Brake pedal depressed | 950 to 1050 Ω |
| Brake pedal released | 203 to 223 Ω |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH) |
Turn the ignition switch off.
Disconnect the skid control ECU (brake actuator assembly) connector.
Disconnect the brake pedal load sensing switch (brake with switch pedal sub-assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| S25-27 (FSW+) - B16-2 | Always | Below 1 Ω |
| S25-27 (FSW+) - Body ground | Always | 10 kΩ or higher |
| B16-1 - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch installation (Click here).
|
| ||||
| OK | ||
| ||