OIL PUMP > INSTALLATION |
| 1. REPLACE TIMING CHAIN COVER OIL SEAL |
![]() |
Place the timing chain cover on wooden blocks.
Using a screwdriver with its tip taped, pry out the oil seal.
![]() |
Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover edge.
Apply a light coat of MP grease to a new oil seal lip.
| 2. INSTALL WATER PUMP |
![]() |
Install a new gasket and the water pump with the 8 bolts.
| 3. INSTALL TIMING CHAIN COVER |
![]() |
Install 3 new O-rings to the timing chain cover as shown in the illustration.
![]() |
Apply adhesive to the timing gear case plug.
![]() |
Using a 10 mm socket hexagon wrench, install the timing gear case plug.
Apply seal packing in a continuous line as shown in the illustration.
| Position | Specified Condition |
| A - A, C - C | 2.5 to 3.0 mm (0.098 to 0.118 in.) |
| B - B, D - D | 4.0 to 4.5 mm (0.157 to 0.177 in.) |
| E | 3.0 to 3.5 mm (0.118 to 0.138 in.) |

![]() |
Align the oil pump's drive rotor spline and crankshaft as shown in the illustration. Install the spline and chain cover plate to the crankshaft.
Loosely install the timing chain cover with the 19 bolts and 2 nuts, but do not tighten the bolts and nuts yet.
Excluding the bolts labeled A and C, tighten the bolts and nuts in this order: Area 1, Area 2 and Area 3.
| Item | Length | Thread Diameter |
| Bolt A | 75 mm (2.95 in.) | 10 mm (0.394 in.) |
| Bolt B | 75 mm (2.95 in.) | 8 mm (0.315 in.) |
| Bolt C | 90 mm (3.54 in.) | 8 mm (0.315 in.) |
| Bolt D | 95 mm (3.74 in.) | 8 mm (0.315 in.) |
| Bolt E | 35 mm (1.38 in.) | 8 mm (0.315 in.) |
| Bolt F | 75 mm (2.95 in.) | 10 mm (0.394 in.) |
Excluding the bolts labeled A, E and F, tighten the bolts and nuts in this order: Area 1, Area 3, Area 2.
Tighten the bolts labeled A in this order: Area 2 and Area 3.
Tighten the bolt labeled F.
Tighten the bolts labeled E in Area 4.

| 4. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring of the sensor.
Install the sensor with the bolt.
Install the connector to the connector bracket.
Attach the harness clamp.
Connect the sensor connector.
| 5. INSTALL NO. 1 OIL PAN |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Temporarily install the oil pan with the 16 bolts and 2 nuts.
Uniformly tighten the 16 bolts and 2 nuts in the order shown in the illustration.
| 6. INSTALL OIL STRAINER |
Install a new gasket and the oil strainer with the bolt and 2 nuts.
| 7. INSTALL NO. 2 OIL PAN |
![]() |
Apply seal packing in a continuous line as shown in the illustration.
![]() |
Temporarily install the oil pan with the 20 bolts and 2 nuts.
Uniformly tighten the 20 bolts and 2 nuts in the order shown in the illustration.
Install a new gasket and the drain plug.
| 8. CHECK CRANKSHAFT PULLEY |
Check that the crankshaft pulley matches the pulley labeled A in the illustration.

| 9. INSTALL CRANKSHAFT PULLEY |
Align the pulley set key with the key groove of the pulley, and slide on the pulley.
![]() |
Using SST, install a new crankshaft pulley bolt.
| 10. INSTALL CAMSHAFT POSITION SENSOR |
Apply a coat of engine oil to a new O-ring.
Install the sensor with the bolt.
| 11. INSTALL CYLINDER HEAD COVER |
Install the 2 cover gaskets to the head cover.
![]() |
Apply seal packing to the places shown in the illustration.
![]() |
Temporarily install the head cover with the 19 bolts and 2 nuts.
Uniformly tighten the 19 bolts and 2 nuts in the order shown in the illustration.
In numerical order, confirm that the bolts labeled 1 to 8 are tightened to the torque specification. Tighten the bolts as necessary.
| 12. INSTALL OIL FILLER CAP |
| 13. INSTALL NO. 1 WATER BY-PASS PIPE |
![]() |
Install a new gasket and the water by-pass pipe with the 2 nuts.
| 14. INSTALL NO. 1 IDLER PULLEY |
Install the spacer, idler pulley and pulley plate with the bolt.
| 15. INSTALL DRIVE BELT TENSIONER |
Temporarily install the belt tensioner with the 3 bolts.
![]() |
Install the tensioner by tightening the 3 bolts in the order shown in the illustration.
| 16. INSTALL THERMOSTAT |
![]() |
Install a new gasket to the thermostat.
Insert the thermostat into the cylinder block with the jiggle valve facing straight upward.
| 17. INSTALL WATER INLET |
Install the inlet with the 2 nuts and bolt.
Connect the connector.
| 18. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET |
![]() |
Temporarily install the No. 1 compressor mounting bracket with the 3 bolts.
Push the No. 1 compressor mounting bracket toward the cylinder block as shown in the illustration and tighten bolt B.

![]() |
Uniformly tighten the 4 bolts in the order shown in the illustration.
| 19. INSTALL GENERATOR |
![]() |
Install the generator with the 2 bolts.
Install the generator wire with the bolt and nut.
Attach the terminal cap.
Connect the connector.
| 20. INSTALL INTAKE MANIFOLD |
![]() |
Install a new gasket and the intake manifold with the 5 bolts and 2 nuts.
Connect the crankshaft position sensor to the clamp.
| 21. INSTALL THROTTLE BODY |
![]() |
Install a new gasket on the intake manifold.
![]() |
Install the throttle body with the 2 bolts and 2 nuts.
Connect the water by-pass hose to the throttle body.
Connector the throttle position sensor and control motor connector.
| 22. INSTALL SPARK PLUG |
| 23. INSTALL IGNITION COIL |
Install the ignition coil with the bolt.
| 24. REMOVE ENGINE ASSEMBLY FROM ENGINE STAND |
| 25. INSTALL ENGINE ASSEMBLY |
Install the engine to the vehicle (Click here).
| 26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 27. ADD ENGINE OIL |
Clean and install the oil drain plug with a new gasket.
Add fresh engine oil.
| Item | Specified Condition |
| Drain and refill with oil filter change | 5.6 liters (5.9 US qts, 4.9 Imp. qts) |
| Drain and refill without oil filter change | 5.3 liters (5.6 US qts, 4.7 Imp. qts) |
| Dry fill | 6.3 liters (6.7 US qts, 5.5 Imp. qts) |
Install the oil filler cap.
| 28. ADD ENGINE COOLANT |
Tighten all the plugs and fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
| Item | Specified Condition |
| A/T | 8.1 liters (8.6 US qts, 7.1 Imp. qts) |
| M/T | 7.8 liters (8.2 US qts, 6.9 Imp. qts) |
Fill the radiator with TOYOTA SLLC to the MAX line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level drops below the MAX line, add TOYOTA SLLC to the MAX line.
Install the radiator cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2,000 to 2,500 rpm.
Press the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine and wait until the coolant cools down to ambient temperature.
![]() |
Check the coolant level in the radiator reservoir.
If the coolant level is below the MIN line, add SLLC to the reservoir MAX line.
| 29. CHECK FUEL FOR LEAKS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Push the intelligent tester main switch ON.
Select the Active Test and enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
Check for fuel leaks.
Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.
If there are fuel leaks, repair or replace parts as necessary.
| 30. CHECK FOR ENGINE OIL LEAKS |
Start the engine, and check that there are no oil leaks after performing maintenance.
| 31. CHECK FOR COOLANT LEAKS |
Check for engine coolant leaks .
| 32. CHECK FUNCTION OF THROTTLE BODY |
![]() |
Check the throttle control motor operating sound.
Turn the ignition switch ON.
When pressing the accelerator pedal, check the operating sound of the running motor. Make sure that no friction noises emit from the motor.
If friction noise is heard, replace the throttle body.
![]() |
Check the throttle position sensor.
Connect the intelligent tester to the DLC3.
Turn the ignition switch ON.
Under Current Data, check that the throttle valve opening percentage (Throttle Pos) is within the standard.
| 33. CHECK IGNITION TIMING |
Warm up the engine and stop the engine.
![]() |
When using the intelligent tester:
Check the ignition timing.
Connect the intelligent tester to the DLC3.
Start the engine at idle.
Turn the intelligent tester main switch ON.
Enter the following item: Powertrain / Engine and ECT / Data List / IGN Advance.
![]() |
When not using the intelligent tester:
Check the ignition timing.
Using SST, connect tachometer probe to terminal TAC of the DLC3.
![]() |
Clamp the tester probe of a timing light to the 4 lead wires or green-red lead wire of the ignition coil connector for No. 1 cylinder.
Start the engine.
![]() |
Using SST, connect terminals TC and CG of the DLC3.

![]() |
Using a timing light, measure the ignition timing.
Remove the SST from terminals 13 (TC) and 4 (CG) of the DLC3.
Check the ignition timing.
Confirm that ignition timing moves to the advanced angle side when the engine speed is increased.
Remove the timing light.
| 34. CHECK ENGINE IDLE SPEED |
Warm up and stop the engine.
When using the intelligent tester:
Check the idle speed.
![]() |
Connect the intelligent tester to the DLC3.
Start the engine at idle.
Turn the intelligent tester main switch ON.
Enter the following item: Powertrain / Engine and ECT / Data List / Engine SPD.
![]() |
When not using the intelligent tester:
Check the idle speed.
Using SST, connect tachometer tester probe to terminal 9 (TAC) of the DLC3.
Start the engine at idle.
Check the idle speed.
| 35. CHECK CO/HC |
Start and warm up the engine.
Run the engine at 2,500 rpm for approximately 180 seconds and idle the engine.
![]() |
Insert CO/HC meter testing probe at least 40 cm (1.3 ft.) into the tailpipe.
Check CO/HC concentration at idle.
If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.
w/ Secondary Air Injection System:
Check the air fuel ratio sensor (Click here) and heated oxygen sensor operation (Click here).
w/o Secondary Air Injection System:
Check the heated oxygen sensor operation (Click here).
See the table below for possible causes, and then inspect and repair the applicable causes if necessary.
| CO | HC | Problems | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (Fluctuating HC reading) |
|
| High | High | Rough idle (Black smoke from exhaust) |
|