Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)

DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock) > INSTALLATION

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY
  1. Clean the contact surfaces of the differential carrier and axle housing.

    NOTICE:
    Be careful not to damage the installation surface.

  1. Install the differential carrier and a new gasket with the 10 nuts and washers.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Be careful to install the gasket without tearing it.



    C237701
  1. Install the differential breather bracket.

  1. Install the rear differential lock actuator protector with the 2 bolts and nut.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



2. CONNECT REAR DIFFERENTIAL LOCK ACTUATOR BREATHER TUBE


    C238709
  1. Connect the rear differential lock actuator breather tube.

  1. Connect the 2 connectors.



3. INSTALL REAR AXLE SHAFT WITH BACKING PLATE LH
(Click here)


4. INSTALL REAR AXLE SHAFT WITH BACKING PLATE RH

HINT:
Use the same procedure described for the LH side.



5. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)



6. ADD DIFFERENTIAL OIL


    D025304E51
  1. Add differential oil so that the oil level is within 5 mm (0 to 0.196 in.) from the bottom lip of the differential filler plug hole.
    Text in Illustration 
    *a
    0 to 5 mm (0 to 0.196 in.)

    NOTICE:
    1. After changing the oil, drive the vehicle, and then check the oil level again.
    2. Too much or too little oil will lead to differential problems.

    If necessary, fill the differential carrier with hypoid gear oil.

    Recommended Viscosity:
    Temperature
    Viscosity
    Above -18°C (0°F)
    SAE 90
    Below -18°C (0°F)
    SAE 80W-90 or SAE 80W

    Oil type:
    Item
    Oil type
    Front Differential
    Rear differential
    Hypoid gear oil API GL-5 or equivalent
    Rear differential (for LSD)
    Hypoid gear oil LSD API GL-5 or equivalent

    Standard Differential Oil Capacity:
    Item
    Specified Condition
    Front Differential
    1.40 to 1.50 liters (1.48 to 1.58 US qts., 1.23 to 1.32 Imp. qts.)
    Rear differential
    3.30 to 3.40 liters (3.49 to 3.59 US qts., 2.91 to 2.99 Imp. qts.)
    4WD, Pre-runner and made for DANA
    2.40 to 2.50 liters (2.54 to 2.64 US qts., 2.11 to 2.20 Imp. qts.)
    w/ Differential lock
    2.85 to 2.95 liters (3.01 to 3.12 US qts., 2.51 to 2.60 Imp. qts.)

  1. Check for oil leakage when the oil level is low.



  1. for front differential:



      A272243E01
    1. Using SST and the 10 mm straight hexagon wrench, 10 mm union nut wrench and socket adaptor, install a new gasket and the differential filler plug.

      SST
      09961-00950  
      Text in Illustration 
      *1
      10 mm Straight Hexagon Wrench
      *2
      10 mm Union Nut Wrench
      *3
      Socket Adaptor

      Torque:
      39 N*m{ 400 kgf*cm , 29 ft.*lbf }

      NOTICE:
      1. Make sure all the tools are connected in a straight line.
      2. Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench.

        Formula:
        T' = T x L3 / (L1 + L2 + L3)
        - T' = Spec. value of torque wrench
        - T = Value of specified tightening torque
        - L1 = Length of union nut wrench
        - L2 = Length of SST
        - L3 = Length of torque wrench

  1. for rear differential:

    1. Install a new gasket and the differential filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



7. BLEED AIR FROM BRAKE LINE
  1. w/ VSC:
    (Click here)

  1. for TSAM Made:
    (Click here)

  1. for TMT Made:
    (Click here)



8. ADJUST PARKING BRAKE
(Click here)


9. INSTALL REAR WHEEL

Torque:
105 N*m{ 1,071 kgf*cm , 77 ft.*lbf }



10. CHECK ABS SPEED SENSOR SIGNAL
  1. w/ VSC:

  1. w/o VSC: