Home › HEATER & AIR CONDITIONING SYSTEM › AIR CONDITIONING › AIR CONDITIONING UNIT

AIR CONDITIONING UNIT > REMOVAL

for Preparation Click here



1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Operate the cooler compressor under the conditions shown below:
    Item
    Condition
    Engine Speed
    Idling
    Operating Time
    3 minutes or more
    A/C Switch Status
    On
    Blower Switch Status
    HI
    Set Temperature
    MAX COOL
    This causes most of the compressor oil from the various components of the A/C system to collect in the A/C compressor.

    NOTICE:
    It is not necessary to operate the cooler compressor if the A/C does not operate because of compressor lock, etc.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.

    HINT:
    Use the refrigerant recovery unit in accordance with the manufacturer's instruction manual.



2. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



4. DRAIN ENGINE COOLANT
  1. for 1GR-FE:

  1. for 2TR-FE:

  1. for 2TR-FBE:

  1. for 1KD-FTV:

  1. for 2KD-FTV:



5. DISCONNECT SUCTION HOSE SUB-ASSEMBLY


    E173197
  1. Remove the bolt and disconnect the suction hose sub-assembly.

    NOTICE:
    E173198E02
    1. Do not use a screwdriver or similar tool to disconnect the suction hose sub-assembly.
    1. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

    Text in Illustration 
    *a
    Disconnect tube by hand

  1. Remove the O-ring from the suction hose sub-assembly.



6. DISCONNECT AIR CONDITIONING TUBE AND ACCESSORY ASSEMBLY
  1. Disconnect the air conditioning tube and accessory assembly.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the air conditioning tube and accessory assembly.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

  1. Remove the O-ring from the air conditioning tube and accessory assembly.



7. DISCONNECT HEATER WATER INLET HOSE


E225468
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water inlet hose.

    HINT:
    Collect the engine coolant in a container.



8. DISCONNECT HEATER WATER OUTLET HOSE


E225469
  1. Using pliers, grip the claws of the clip and slide the clip to disconnect the heater water outlet hose.

    HINT:
    Collect the engine coolant in a container.



9. REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


10. REMOVE NO. 2 HEATER TO REGISTER DUCT


E225181
  1. Remove the 3 clips and No. 2 heater to register duct.



11. REMOVE NO. 1 HEATER TO REGISTER DUCT


E225182
  1. Remove the clip.

  1. Detach the 3 claws and remove the No. 1 heater to register duct.



12. REMOVE NO. 3 HEATER TO REGISTER DUCT


E225183
  1. Remove the clip.

  1. Detach the 4 claws and remove the No. 3 heater to register duct.



13. REMOVE DEFROSTER NOZZLE ASSEMBLY


E225184
  1. Using a screwdriver, detach the 4 clips and remove the defroster nozzle assembly.



14. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)


15. REMOVE STEERING COLUMN ASSEMBLY
(Click here)


16. REMOVE NO. 1 AIR DUCT


E226311
  1. Detach the 2 claws and remove the No. 1 air duct.



17. REMOVE NO. 2 AIR DUCT


E226312
  1. Detach the 2 claws and remove the No. 2 air duct.



18. REMOVE NO. 4 AIR DUCT


E226313
  1. Detach the 2 claws and remove the No. 4 air duct.



19. REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY


E225185E01

    1. Detach the 2 clamps and remove the 2 nuts labeled A.

    2. Disconnect the connectors and remove the driver side junction block.

    3. Remove the screw.

    4. Remove the bolt, nut labeled B and No. 1 instrument panel brace sub-assembly.
      Text in Illustration 
      *1
      Screw
      *2
      Nut A
      *3
      Nut B
      *4
      Bolt



20. REMOVE AIR CONDITIONING DUCT SUB-ASSEMBLY (for Automatic Air Conditioning System)


E225928
  1. Detach the 2 claws and remove the air conditioning duct sub-assembly.



21. REMOVE ECM
  1. for 1GR-FE:
    (Click here)

  1. for 2TR-FE:
    (Click here)

  1. for 2TR-FBE:
    (Click here)

  1. for 1KD-FTV, w/o Glow Plug Controller:
    (Click here)

  1. for 1KD-FTV, w/ Glow Plug Controller:
    (Click here)

  1. for 2KD-FTV:
    (Click here)



22. REMOVE INSTRUMENT PANEL REINFORCEMENT


E225186
  1. Disconnect the connector and detach the 3 clamps.



    E225187
  1. Detach the 2 clamps and disconnect the 2 connectors.



    E225188
  1. Remove the 2 bolts and disconnect the ground wires from the instrument panel reinforcement.



    E225885
  1. Remove the grommet from the vehicle body.



  1. Detach the 12 clamps.


    E225189

  1. Disconnect the connectors.



  1. Remove the 3 bolts.


    E225190

  1. for Automatic Transmission:
    Remove the 7 bolts and instrument panel reinforcement.



  1. for Manual Transmission:
    Remove the 8 bolts and instrument panel reinforcement.


    E225191E01


    Text in Illustration 
    *A
    for Manual Transmission
    -
    -



23. REMOVE NO. 1 COOLER UNIT DRAIN HOSE


E225884
  1. Remove the No. 1 cooler unit drain hose.



24. REMOVE AIR CONDITIONING UNIT ASSEMBLY


E225192
  1. Remove the bolt, nut and air conditioning unit assembly.



25. REMOVE NO. 3 AIR DUCT


E226397
  1. Detach the 2 claws and remove the No. 3 air duct.