Home › TRANSMISSION ยท A750F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY (for 1KD-FTV)

AUTOMATIC TRANSMISSION ASSEMBLY (for 1KD-FTV) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



4. DRAIN TRANSFER OIL


5. INSTALL CONSOLE BOX ASSEMBLY
(Click here)


6. REMOVE SHIFT LEVER BOOT ASSEMBLY


    C239519
  1. Remove the 4 screws and shift lever boot.



7. REMOVE TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY
  1. Fold back the transfer front drive shift boot.



    C213734
  1. Using needle-nose pliers, remove the snap ring and pull out the shift lever.

    HINT:
    Move the transfer shift lever to the H4 position.



8. REMOVE NO. 1 ENGINE UNDER COVER


9. REMOVE NO. 2 ENGINE UNDER COVER


10. REMOVE EXHAUST PIPE
(Click here)


11. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


12. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)


13. DISCONNECT OIL COOLER TUBE


C187501
  1. Using a union nut wrench, disconnect the tube outlet and tube inlet.



    C187500
  1. Remove the 3 bolts and 3 clamps.



14. DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C111231
  1. Remove the nut and clip and disconnect the control cable.



15. REMOVE NO. 1 TRANSMISSION CONTROL CABLE BRACKET


C111232
  1. Remove the 2 bolts and control cable bracket from the transmission.



16. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY


C111233
  1. Support the transmission with a transmission jack.



17. REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY


G034256E02
  1. Remove the 4 set bolts of the rear No. 1 engine mounting insulator.

  1. Remove the 4 nuts, 4 bolts and frame crossmember.



18. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR


G034260E01
  1. Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission.



19. DISCONNECT WIRE HARNESS


    C214940
  1. Remove the nut and disconnect the ground cable.



    C112845
  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the 8 connectors and detach the 7 clamps.

  1. Remove the bolt and disconnect the wire harness.



20. REMOVE STARTER ASSEMBLY
(Click here)


21. REMOVE STIFFENER PLATE


C187502E03
Text in Illustration 
*A
LH Side
*B
RH Side
  1. Remove the 4 bolts and stiffener plate RH (with oil cooler tube clamp).

  1. Remove the 4 bolts and stiffener plate LH.

  1. Remove the No. 4 cylinder block insulator.

  1. Remove the end plate.



22. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT


    G034258E01
  1. Turn the crankshaft to gain access to the 6 torque converter setting bolts and remove each bolt through the hole of the flywheel while holding the crankshaft pulley bolt with a wrench.



23. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY


    G034259E01
  1. Remove the 5 bolts.

  1. Remove the automatic transmission assembly.

    NOTICE:
    1. Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.
    2. Do not use excess force to pry on the transmission assembly.



24. REMOVE TRANSFER ASSEMBLY
  1. Remove the 8 bolts and 2 clamps.

  1. Remove the transfer from the transmission.



25. REMOVE TORQUE CONVERTER ASSEMBLY