Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > INSTALLATION

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. INSTALL CYLINDER HEAD GASKET


    A060285E02
  1. Find where the piston head protrudes most by slowly turning the crankshaft clockwise and counterclockwise.
    Text in Illustration 
    *1
    Measuring Tip
    *2
    Protrusion



    A058134E02
  1. Measure the piston protrusion of each cylinder at 2 points as shown in the illustration.
    Text in Illustration 
    *1
    Measuring Point

  1. For the piston protrusion value of each cylinder, use the average of the 2 measurements of each cylinder.

    Piston protrusion:
    0.005 to 0.255 mm (0.000197 to 0.0100 in.)

    HINT:
    After installing the piston and connecting rod assembly, if the protrusion is not as specified, remove the piston and connecting rod assembly and reinstall them.



    A060174E02
  1. Select a new cylinder head gasket.
    Text in Illustration 
    *1
    Cutout Mark
    V100135
    Front

    HINT:
    New cylinder head gaskets are available in 5 sizes, and are marked A, B, C, D or E.

    New Cylinder Head Gasket Thickness:
    Mark
    Specified Condition
    A
    0.80 to 0.90 mm (0.0315 to 0.0354 in.)
    B
    0.85 to 0.95 mm (0.0335 to 0.0374 in.)
    C
    0.90 to 1.00 mm (0.0354 to 0.0394 in.)
    D
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)
    E
    1.00 to 1.10 mm (0.0394 to 0.0433 in.)


    1. Select the largest piston protrusion value from the measurements made. Then select a new gasket according to the table below.

      Gasket Size:

      Item
      Specified Condition
      Piston protrusion
      0.005 to 0.054 mm (0.000197 to 0.00213 in.)
      0.055 to 0.104 mm (0.00217 to 0.00409 in.)
      0.105 to 0.154 mm (0.00413 to 0.00606 in.)
      0.155 to 0.204 mm (0.00610 to 0.00803 in.)
      0.205 to 0.255 mm (0.00807 to 0.0100 in.)
      Gasket to be used
      A
      B
      C
      D
      E



    A060144E02
  1. Place the cylinder head gasket on the cylinder block.
    Text in Illustration 
    V100135
    Front

    NOTICE:
    Make sure the gasket is installed facing the proper direction.



2. INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
  1. The cylinder head bolts are tightened in 3 progressive steps.
  2. If any bolt is broken or deformed, replace it.

  1. Place the cylinder head on the cylinder head gasket.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.



    A060284E01
  1. Install the 18 washers with the 18 cylinder head bolts, and uniformly tighten the bolts in several passes in the sequence shown in the illustration.

    Torque:
    85 N*m{ 867 kgf*cm , 63 ft.*lbf }

    Standard Bolt Length:
    Item
    Specified Condition
    A
    110 mm (4.33 in.)
    B
    167 mm (6.57 in.)

    If any one the cylinder head bolts does not meet the torque specification, replace it.



    A060141E03
  1. Mark the front of each cylinder head bolt with paint.
    *1
    Painted Mark
    *a
    Front

  1. Further tighten the cylinder head bolts by 90° in the sequence shown in the illustration.

  1. Tighten the cylinder head bolts by an additional 90°.

  1. Check that the painted marks are now facing rearward.



3. INSTALL VALVE LIFTER
  1. Install the valve lifters.

  1. Check that each valve lifter rotates smoothly by hand.



4. INSTALL CAMSHAFT


    G036616E02
  1. Using the crankshaft pulley bolt, set the No. 1 cylinder to 90° BTDC/compression.
    Text in Illustration 
    *1
    Key

    HINT:
    Set the No. 1 cylinder to 90° BTDC/compression to prevent the top of the piston from hitting against the valve head.



  1. Install the camshaft.

    1. Apply engine oil to the thrust portion of the camshaft.



    2. A060149E04
    3. Place the camshaft on the cylinder head with the key groove facing upward.
      Text in Illustration 
      *1
      Key Groove
      *a
      Upward



    4. A060150E01
    5. Align the timing marks (1-dot marks) of the camshaft drive and driven main gears and set the No. 2 camshaft in place.

  1. Remove any old seal packing (FIPG material) from the camshaft bearing cap.



    A060283E05
  1. Apply seal packing to the specified areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Standard seal diameter:
    4 mm (0.157 in.)

    Text in Illustration 
    *1
    Seal Packing
    *2
    Oil Passage

    NOTICE:
    1. Do not allow seal packing to contact the oil passage of the bearing cap.
    2. After applying seal packing, install the camshaft bearing caps within 3 minutes and tighten the bolts within 15 minutes.
    3. Do not start the engine for at least 2 hours after installation.



    A060146E01
  1. Install the 5 bearing caps to their proper locations.



    A060147E02
  1. Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.

  1. Install and uniformly tighten the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }



  1. Install a new camshaft oil seal.

    1. Apply MP grease to the lip of a new oil seal.



    2. A060145E01
    3. Using SST and a hammer, tap in the oil seal until its surface is flush with the surfaces of the camshaft bearing cap and cylinder head.

      SST
      09608-06041  



5. INSTALL CYLINDER BLOCK INSULATOR
  1. Install the cylinder block insulator to the cylinder head.



6. INSTALL NO. 2 TIMING BELT COVER


    A060279E02
  1. Apply seal packing (FIPG) to the specified areas shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    After applying seal packing, install the No. 2 timing belt cover within 3 minutes and tighten the bolts and nut within 15 minutes.

  1. Clean the bolts and their holes.

  1. Apply adhesive to 2 or 3 threads at the end of each of the 4 bolts.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the No. 2 timing belt cover with the 4 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }



7. INSTALL CAMSHAFT TIMING PULLEY
  1. Install the camshaft timing pulley.

  1. Install the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    Torque:
    98 N*m{ 1000 kgf*cm , 72 ft.*lbf }



8. INSTALL TIMING BELT
(Click here)


9. INSPECT AND ADJUST VALVE CLEARANCE
(Click here)


10. INSTALL EXHAUST MANIFOLD
  1. Temporarily install a new gasket, the exhaust manifold, 8 new collars and the 8 plate washers to the cylinder head with 8 new nuts.



    A260675E01
  1. Tighten the 8 nuts in the order shown in the illustration.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    Make sure that the side of the collar with the smaller diameter faces the exhaust manifold.



11. INSTALL NO. 1 COMPRESSOR MOUNTING BRACKET (w/ Air Conditioning System)
  1. Install the No. 1 compressor mounting bracket with the 4 bolts.

    Torque:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }



12. INSTALL COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)
  1. Connect the cooler compressor with the 4 bolts.

    Torque:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }



13. INSTALL FAN SHROUD
(Click here)


14. INSTALL TURBOCHARGER SUB-ASSEMBLY
(Click here)


15. INSTALL COMMON RAIL ASSEMBLY
  1. w/ Glow Plug Controller: (Click here)
  2. w/o Glow Plug Controller: (Click here)


16. INSTALL INJECTOR ASSEMBLY
  1. w/ Glow Plug Controller: (Click here)
  2. w/o Glow Plug Controller: (Click here)


17. INSTALL GLOW PLUG ASSEMBLY
  1. w/ Glow Plug Controller: (Click here)
  2. w/o Glow Plug Controller: (Click here)


18. INSTALL INTAKE MANIFOLD
  1. w/ Glow Plug Controller: (Click here)
  2. w/o Glow Plug Controller: (Click here)


19. ADD ENGINE OIL
  1. Add new engine oil.

    Standard Oil Grade:

    Item
    Oil Grade
    Oil Viscosity (SAE)
    w/ Glow Plug Controller
    API CF-4, CF or ACEA B1
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50
    (5W-30 is best choice for fuel economy and good starting in cold winter.)
    w/o Glow Plug Controller
    G-DLD1, API CF-4, CF or ACEA B1
    - 5W-30
    - 10W-30
    - 15W-40
    - 20W-50


    Standard Capacity:

    Item
    Specified Condition
    Drain and refill without oil filter change
    6.6 liters (7.0 US qts, 5.8 Imp. qts)
    Drain and refill with oil filter change
    6.9 liters (7.3 US qts, 6.1 Imp. qts)
    Dry fill
    7.4 liters (7.8 US qts, 6.5 Imp. qts)

  1. Install the oil filler cap.



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



21. ADD ENGINE COOLANT
  1. Tighten the radiator drain cock plug by hand.

  1. Tighten the cylinder block drain cock plug.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



    A098989E01
  1. Fill the radiator with TOYOTA Super Long Life Coolant (SLLC) to the reservoir tank's B line.

    Standard capacity:
    Item
    Specified Condition
    A/T
    11.1 liters (11.7 US qts, 9.8 Imp. qts)
    M/T
    9.8 liters (10.4 US qts, 8.6 Imp. qts)

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).
    1. Please contact your TOYOTA dealer for further details.

    NOTICE:
    Never use water as a substitute for engine coolant.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
    If the coolant level drops below the B line, add TOYOTA SLLC to the B line.

  1. Install the radiator reservoir cap.



    A099591E01
  1. Using a wrench, install the vent plug.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }

  1. Bleed air from the cooling system.

    1. Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.

    2. Maintain the engine speed at 2,500 to 3,000 rpm.

    3. Press the inlet and outlet radiator hoses several times by hand to bleed air.

      CAUTION:
      When pressing the radiator hoses:
      1. Wear protective gloves.
      1. Be careful as the radiator hoses are hot.
      1. Keep your hands away from the radiator fan.

    4. Stop the engine and wait until the coolant cools down to ambient temperature.

      CAUTION:
      Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    G036768E01
  1. After the coolant cools down, check that the coolant level is at the F line.
    If the coolant level is below the F line, add TOYOTA SLLC to the F line.



22. BLEED AIR FROM FUEL SYSTEM
  1. w/ Glow Plug Controller: (Click here)
  2. w/o Glow Plug Controller: (Click here)


23. INSPECT FOR COOLANT LEAK
  1. Check for engine coolant leaks (Click here).



24. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.



25. INSPECT FOR FUEL LEAK
  1. w/ Glow Plug Controller:
  2. w/o Glow Plug Controller:


26. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait 5 minutes. The engine oil level should be between the dipstick low level mark and full level mark.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.



27. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Torque:
28 N*m{ 286 kgf*cm , 21 ft.*lbf }