Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › CYLINDER HEAD

CYLINDER HEAD > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.



4. REMOVE INTAKE MANIFOLD
(Click here)


5. REMOVE GLOW PLUG ASSEMBLY
(Click here)


6. REMOVE INJECTOR ASSEMBLY
(Click here)


7. REMOVE COMMON RAIL ASSEMBLY
(Click here)


8. REMOVE TURBOCHARGER SUB-ASSEMBLY
(Click here)


9. REMOVE FAN SHROUD
(Click here)


10. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



11. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



12. REMOVE EXHAUST MANIFOLD


    A152664
  1. Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.

  1. Remove the gasket.



13. REMOVE TIMING BELT
(Click here)


14. REMOVE CAMSHAFT TIMING PULLEY


    A060182E01
  1. Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure to remove the bolt of the camshaft timing pulley with the timing belt not installed.

  1. Remove the camshaft timing pulley.



15. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and timing belt cover.



16. REMOVE CYLINDER BLOCK INSULATOR (w/ EGR Cooler)


    A149941
  1. Remove the cylinder block insulator from the cylinder head.



17. REMOVE CAMSHAFT


    A060148E02
  1. Face the key groove of the camshaft upward by turning the camshaft with a wrench.



    A060147E01
  1. Uniformly loosen the 15 bearing cap bolts in several passes in the sequence shown in the illustration.

  1. Remove the 5 bearing caps, oil seal and 2 camshafts.



18. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    A059194E01
  1. Uniformly loosen the 18 cylinder head bolts in several passes in the sequence shown in the illustration. Then remove the 18 cylinder head bolts and 18 washers.

    NOTICE:
    Head warpage or cracking could result from removing bolts in the incorrect order.

  1. Lift the cylinder head from the dowels on the cylinder block, and place the cylinder head on wooden blocks on a bench.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.

    HINT:
    If the cylinder head is difficult to lift, use a screwdriver to pry between the cylinder head and block.



19. REMOVE CYLINDER HEAD GASKET