FUEL LID LOCK CONTROL > REMOVAL |
| 1. REMOVE FRONT SEAT ASSEMBLY LH |
for Manual Seat:
(Click here)
for Power Seat:
(Click here)
| 2. REMOVE FRONT SEAT ASSEMBLY RH |
| 3. REMOVE REAR NO. 1 SEAT ASSEMBLY LH |
| 4. REMOVE REAR NO. 1 SEAT ASSEMBLY RH |
| 5. REMOVE REAR NO. 2 SEAT ASSEMBLY LH (w/ Rear No. 2 Seat) |
| 6. REMOVE CONSOLE BOX ASSEMBLY |
| 7. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover) |
Remove the tonneau cover.
| 8. REMOVE TONNEAU COVER HOLDER LH (w/ Tonneau Cover) |
![]() |
Remove the screw and tonneau cover holder.
| 9. REMOVE TONNEAU COVER HANGER LH (w/ Tonneau Cover) |
![]() |
Remove the screw and tonneau cover hanger.
| 10. REMOVE FRONT DOOR SCUFF PLATE LH |
![]() |
Put protective tape around the front door scuff plate.
| *1 | Protective Tape |
Using a moulding remover, detach the 7 claws and 3 clips and remove the front door scuff plate.
| 11. REMOVE COWL SIDE TRIM BOARD LH |
![]() |
Remove the part of the front door opening trim attached to the cowl side trim board.
Remove the clip.
Detach the 2 clips and remove the cowl side trim board.
| 12. REMOVE REAR DOOR SCUFF PLATE LH |
![]() |
Put protective tape around the rear door scuff plate.
| *1 | Protective Tape |
Using a moulding remover, detach the 7 claws and 2 clips and remove the rear door scuff plate.
| 13. REMOVE LOWER CENTER PILLAR GARNISH LH |
![]() |
Detach the 2 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and disconnect the front seat outer belt floor anchor.
![]() |
Remove the part of the front door opening trim and rear door opening trim weatherstrip attached to the lower center pillar garnish.
Detach the 2 claws, 2 guides and 2 clips and remove the lower center pillar garnish.
| 14. REMOVE BACK DOOR SCUFF PLATE |
![]() |
Detach the 4 claws, 2 guides and 6 clips and remove the back door scuff plate.
| 15. REMOVE QUARTER TRIM HOOK |
![]() |
Remove the screw and quarter trim hook.
| 16. REMOVE QUARTER INSIDE TRIM BOARD LH |
![]() |
Detach the 2 claws and remove the outer lap belt anchor cover.
![]() |
Remove the bolt and disconnect the rear No. 1 seat outer belt floor anchor.
![]() |
w/ Rear No. 2 Seat:
Remove the bolt and disconnect the rear No. 2 seat outer belt floor anchor.
Remove the part of the rear door opening trim weatherstrip attached to the quarter inside trim board.
Using a clip remover, remove the clip.
Detach the 7 claws and 10 clips.
Disconnect the power point socket connector and remove the quarter inside trim board.

| 17. REMOVE FRONT FLOOR CARPET ASSEMBLY |
Partially remove the floor carpet.
| 18. REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY |
Remove the fuel lid lock open lever.
Remove the tape and detach the cable from each of the clamps shown in the illustration.

| *1 | Fuel Lid Lock Open Lever | *2 | Tape |
![]() |
Turn the fuel filler opening lid lock retainer counterclockwise and remove the fuel lid lock control cable from the fuel filler opening lid lock retainer.
| 19. REMOVE FUEL FILLER OPENING LID LOCK RETAINER |
![]() |
Turn the fuel filler opening lid lock retainer clockwise and remove the fuel filler opening lid lock retainer as shown in the illustration.