Home › ENGINE ยท 1KD-FTV › LUBRICATION › OIL PUMP (w/o Glow Plug Controller)

OIL PUMP (w/o Glow Plug Controller) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



4. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A112147E01



5. REMOVE ENGINE ASSEMBLY
(Click here)


6. REMOVE NO. 1 TIMING BELT COVER


    A015094E01
  1. Remove the 6 bolts, 6 washers and timing belt cover.



7. REMOVE TIMING BELT


    A070549E05
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.



    A070550E01
  1. Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.



  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.



8. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

NOTICE:
When inspecting the No. 1 timing belt idler, do not remove it unless absolutely necessary.

  1. Using a 10 mm hexagon wrench, remove the bolt, No. 1 timing belt idler and washer.



9. REMOVE NO. 2 IDLE PULLEY ASSEMBLY
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.



10. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



11. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.



12. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.



13. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



14. REMOVE DIESEL THROTTLE BODY ASSEMBLY (w/ EGR Cooler)
  1. Disconnect the 2 connectors.



    A111832
  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.



15. REMOVE MANIFOLD STAY WITH VACUUM SWITCHING VALVE (w/ EGR Cooler)
  1. Disconnect the 2 vacuum switching valve connectors and the 4 vacuum transmitting hoses.



    A148131
  1. Remove the 2 bolts and manifold stay with vacuum switching valve.



16. REMOVE MANIFOLD STAY (w/o EGR Cooler)


    A099622E01
  1. Remove the 2 bolts and manifold stay.



17. DISCONNECT NO. 3 WATER BY-PASS HOSE (w/ EGR Cooler)


    A147224E02
  1. Remove the clamp.

  1. Disconnect the No. 3 water by-pass hose from the EGR cooler.



18. DISCONNECT NO. 4 WATER BY-PASS HOSE (w/ EGR Cooler)
  1. Disconnect the No. 4 water by-pass hose from the EGR cooler.



19. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
  1. After removing the fuel pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the fuel pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.



  1. w/ EGR Cooler:



      A153263E01
    1. Remove the 2 nuts and No. 3 injection pipe clamp.



    2. A153264E01
    3. Remove the 2 bolts and 2 No. 2 injection pipe clamps.



    4. A153266E07
    5. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



  1. w/o EGR Cooler:



      A231803E01
    1. Remove the bolt and No. 2 injection pipe clamp.

    2. Remove the 2 nuts and No. 3 injection pipe clamp.

    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.



20. REMOVE NO. 2 INTAKE AIR CONNECTOR BRACKET (w/ EGR Cooler)


    A147215
  1. Remove the 3 bolts and No. 2 intake air connector bracket.



21. REMOVE NO. 3 WATER BY-PASS PIPE (w/ EGR Cooler)


    A147216
  1. Remove the 2 bolts and disconnect the No. 3 water by-pass pipe with wire harness.



22. REMOVE NO. 1 GAS FILTER WITH GAS FILTER BRACKET (w/ EGR Cooler)


    A211909
  1. Disconnect the 2 vacuum hoses.

  1. Remove the bolt and No. 1 gas filter with gas filter bracket.



23. REMOVE ELECTRIC VACUUM REGULATING VALVE ASSEMBLY (w/ EGR Cooler)


  1. w/ EGR Cooler:



      A211910
    1. Disconnect the connector.



    2. A211911
    3. Disconnect the 4 vacuum hoses.



    4. A211912
    5. Remove the 2 bolts and electric vacuum regulating valve with bracket.

      NOTICE:
      Do not remove the electric vacuum regulating valve from the bracket.



  1. w/o EGR Cooler:



      A250417
    1. Disconnect the 2 connectors.

    2. Disconnect the 3 vacuum hoses.

    3. Remove the 2 bolts and electric vacuum regulating valve together with the bracket.

      NOTICE:
      Do not remove the electric vacuum regulating valve from the bracket.



    4. A112098
    5. Remove the screw and vacuum switching valve.



24. REMOVE NO. 2 INTAKE AIR CONNECTOR (w/ EGR Cooler)


    A147230
  1. Remove the 3 nuts, No. 2 intake air connector and gasket.



25. REMOVE INTAKE AIR CONNECTOR (w/ EGR Cooler)


    A147219
  1. Remove the 3 bolts, intake air connector and 2 gaskets.



26. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY WITH NO. 2 EGR VALVE AND EGR COOLER (w/ EGR Cooler)
  1. Disconnect the EGR valve position sensor connector.



    A147220
  1. Disconnect the vacuum hose from the No. 2 EGR valve.



    A147225
  1. Remove the bolt, 2 nuts, electric EGR control valve with No. 2 EGR valve and EGR cooler.

  1. Remove the gasket from the cylinder head.



27. REMOVE NO. 4 INJECTION PIPE SUB-ASSEMBLY

NOTICE:
If an injection pipe clamp is removed from the No. 4 injection pipe, replace the injection pipe clamp with a new one.



  1. w/ EGR Cooler:



      A152275
    1. Remove the bolt and disconnect the injection pipe clamp.



    2. A152276E09
    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



  1. w/o EGR Cooler:



      A098893E01
    1. Remove the 2 bolts and disconnect the 2 injection pipe clamps.



    2. A231804E01
    3. Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 4 injection pipe.



28. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the engine oil level dipstick.

  1. Remove the bolt and injection pipe clamp.

  1. Remove the bolt and engine oil level dipstick guide.

  1. Remove the O-ring engine oil level dipstick guide.



29. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A098969E03
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



30. REMOVE NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY
  1. Disconnect the 3 fuel hoses.



    A257062E02
  1. Remove the union bolt, 3 bolts, No. 2 nozzle leakage pipe and gasket.



31. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

NOTICE:
If the cylinder head cover is removed, replace the 4 No. 3 cylinder head cover gaskets with new ones.



    A152277
  1. Remove the 3 bolts and disconnect the 4 connectors.

  1. Disconnect the ventilation hose.



    A060180E01
  1. Using a small screwdriver, remove the nozzle holder seal by prying between the nozzle holder seal and the cutout part of the cylinder head cover.



    G034877E01
  1. Remove the 10 bolts, 2 nuts, cylinder head cover and cylinder head cover gasket.



    A289511
  1. Remove the 4 No. 3 cylinder head cover gaskets from the cylinder head cover.



32. REMOVE CAMSHAFT TIMING PULLEY


    A060182E01
  1. Remove the bolt of the camshaft timing pulley while holding the camshaft with a wrench.

    NOTICE:
    Make sure the timing belt is not installed when removing the bolt of the camshaft timing pulley.

  1. Remove the camshaft timing pulley.



33. REMOVE NO. 2 TIMING BELT COVER
  1. Remove the 4 bolts, nut and No. 2 timing belt cover.



34. REMOVE WATER PUMP ASSEMBLY


    A225339
  1. Remove the 5 bolts, 2 nuts, engine water pump and gasket.



35. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)


    A148171
  1. Remove the bolt and timing gear cover insulator.



36. REMOVE VACUUM PUMP ASSEMBLY


    A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



37. REMOVE VANE PUMP ASSEMBLY


    A233594
  1. Remove the 2 nuts, vane pump and O-ring.



38. REMOVE CAMSHAFT POSITION SENSOR


A112046
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.



39. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.



  1. Detach the 3 clips, and the bolt and crankshaft position sensor.


    A253484



40. REMOVE PUMP DRIVE SHAFT PULLEY


    A038747E01
  1. Remove the 4 bolts, No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E01
  1. Using SST, hold the crankshaft pulley and remove the nut and O-ring.

    SST
    09213-58014  
    09330-00021  



41. REMOVE CRANKSHAFT PULLEY


    A251844E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A251845E01
  1. Using SST, remove the pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



42. REMOVE TIMING GEAR COVER

NOTICE:
As the fuel supply pump is not installed, the injection gear is loose inside the timing gear case. Do not allow the injection gear to fall.

HINT:
To prevent the injection gear from falling, temporarily install the fuel supply pump.



    A100853
  1. Remove the 14 bolts and 2 nuts.



    A102800
  1. Pry the timing gear cover at the locations shown in the illustration and remove the timing gear cover.

    NOTICE:
    Be careful not to drop the injection gear.



    A051310E01
  1. Remove the O-ring from the timing gear case.



43. REMOVE INJECTION GEAR


    A071164E01
  1. Using SST, remove the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)



44. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    A239296
  1. Remove the No. 1 crankshaft position sensor plate.



45. REMOVE CRANKSHAFT TIMING GEAR


    A222332E01
  1. Using SST, remove the crankshaft timing gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05010, 09954-05021)



46. REMOVE NO. 1 IDLE GEAR


    A238858
  1. Remove the No. 1 idle gear together with the No. 2 idle sub gear.



47. REMOVE NO. 1 IDLE GEAR SHAFT


    A238859
  1. Remove the No. 1 idle gear shaft.



48. REMOVE FUEL SUPPLY PUMP ASSEMBLY


    G036615E01
  1. Remove the bolt and clamp.

  1. Remove the bolt and oil dipstick guide.



    A098969E09
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



    A098895E01
  1. Disconnect the 2 fuel hoses.



    A098896E01
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley using SST.

    SST
    09213-58013  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold or carry the pump by holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



49. REMOVE OIL PAN SUB-ASSEMBLY
  1. Remove the 22 bolts and 2 nuts.



    Z004119E03
  1. Insert the blade of an oil pan seal cutter between the oil pan and cylinder block, cut through the applied sealer and remove the oil pan.

    NOTICE:
    1. Do not use the oil pan seal cutter for the area between the oil pan and timing belt case, or for the area between the oil pan and rear oil seal retainer.
    2. Be careful not to damage the oil pan flange.



50. REMOVE OIL STRAINER SUB-ASSEMBLY
  1. Remove the 2 bolts, 2 nuts, oil strainer and gasket.



51. REMOVE TIMING GEAR CASE ASSEMBLY


    A069842E01
  1. Remove the union bolt and 8 bolts.



    A102853
  1. Pry the timing gear case at the location shown in the illustration and remove the gear case and gasket.



    A069840E03
  1. Remove the 2 O-rings.