Home › ENGINE ยท 1KD-FTV › ENGINE MECHANICAL › ENGINE ASSEMBLY (w/o Glow Plug Controller)

ENGINE ASSEMBLY (w/o Glow Plug Controller) > REMOVAL

for Preparation Click here


NOTICE:
  1. When replacing the injectors (including shuffling the injectors between the cylinders), common rail or cylinder head, it is necessary to replace the injection pipes with new ones.
  2. When replacing the fuel supply pump, common rail, cylinder block, cylinder head, cylinder head gasket or timing gear case, it is necessary to replace the fuel inlet pipe with a new one.
  3. After removing the injection pipes, clean them with a brush and compressed air.



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



3. REMOVE HOOD SUB-ASSEMBLY
  1. Disconnect the washer nozzle hose.

  1. Remove the 4 bolts and hood.



4. REMOVE NO. 1 ENGINE UNDER COVER


5. REMOVE NO. 2 ENGINE UNDER COVER


6. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }



7. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A099591E01
  1. Drain the coolant by removing the reservoir cap and, using a wrench, remove the vent plug.



  1. Loosen the cylinder block drain cock plug and the radiator drain cock plug.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.



    A112147E01



8. DRAIN TRANSMISSION OIL (for Manual Transmission)
  1. Remove the drain plug and gasket to drain the oil.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



9. DRAIN TRANSMISSION FLUID (for Automatic Transmission)
  1. Remove the drain plug and gasket, and drain ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 205 kgf*cm , 15 ft.*lbf }



10. DRAIN POWER STEERING FLUID


11. REMOVE BATTERY CLAMP SUB-ASSEMBLY
  1. Remove the bolt, nut and battery clamp.



12. REMOVE BATTERY


13. REMOVE BATTERY TRAY


14. REMOVE AIR CLEANER ASSEMBLY
  1. Disconnect the mass air flow meter connector.

  1. Loosen the hose clamp.

  1. Remove the 2 bolts and air cleaner.



15. REMOVE INTERCOOLER ASSEMBLY WITH INTAKE AIR CONNECTOR
(Click here)


16. REMOVE RADIATOR ASSEMBLY
(Click here)


17. REMOVE STARTER ASSEMBLY
  1. for 2.2 kW Type Bosch Made: (Click here)
  2. for 2.2 kW Type Denso Made: (Click here)


18. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)


19. REMOVE FRONT PROPELLER SHAFT ASSEMBLY


C098708E01
  1. Place matchmarks on the propeller shaft flange and differential.

  1. Remove the 4 nuts, 4 bolts and 4 washers, and disconnect the propeller shaft.



    F052086E01
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts, 4 washers and front propeller shaft.



20. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY
(Click here)


21. DISCONNECT HEATER HOSE


    A236415
  1. Disconnect the 2 heater hoses.



22. DISCONNECT PRESSURE FEED TUBE ASSEMBLY


    A236416
  1. Disconnect the oil reservoir to pump hose.



    A236417
  1. Disconnect the pressure feed tube.



23. DISCONNECT FUEL HOSE


    A236418
  1. Disconnect the 2 fuel hoses.



24. DISCONNECT UNION TO CONNECTOR TUBE HOSE


    A236419
  1. Disconnect the union to connector tube hose.



25. REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY


B278058E01
  1. Slightly bend the upper part of the glove compartment door to release the 2 stoppers and open the glove compartment door until it is horizontal.
    Text in Illustration 
    *1
    Stopper



    B278059E01
  1. Pull the glove compartment door toward the rear of the vehicle to detach the 2 hinges and remove the glove compartment door.
    Text in Illustration 
    *1
    Hinge



26. DISCONNECT WIRE HARNESS


A236420
  1. Remove the upper relay block cover.

  1. Remove the side relay block cover.

  1. Remove the nut and disconnect the engine room junction block wire.

  1. Disconnect the 2 engine room junction block connectors.

  1. Remove the bolt and disconnect the ground cable.



    A233020
  1. Remove the 2 nuts, detach the clamp and disconnect the wire harness.



    A237901
  1. Disconnect the 3 injector driver connectors.



    A253827
  1. Disconnect the turbo motor driver connector.

  1. Disconnect the 4WD control ECU connector.

  1. for Automatic Transmission:
    Disconnect the 3 TCM connectors.

  1. Disconnect the 4 ECM connectors.



27. DISCONNECT COOLER COMPRESSOR ASSEMBLY
  1. Remove the 4 bolts and disconnect the cooler compressor.

    HINT:
    It is not necessary to completely remove the cooler compressor. With the hoses connected to the cooler compressor, hang the cooler compressor on the vehicle body with a rope.



28. REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)
(Click here)


29. REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for Automatic Transmission)


30. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)
(Click here)


31. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

HINT:
Perform this procedure only when replacement of the rear No. 1 engine mounting insulator is necessary.

  1. Remove the 4 bolts and rear No. 1 engine mounting insulator.



32. REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)


D029616E03
  1. Place matchmarks on the clutch cover and flywheel.

  1. Loosen each set bolt one turn at a time until spring tension is released.

  1. Remove the 6 set bolts and pull off the clutch cover.

    NOTICE:
    Do not drop the clutch disc.



33. REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

NOTICE:
Keep the lining part of the clutch disc, pressure plate and surface of the flywheel away from oil and foreign matter.



34. REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114803
  1. Remove the 8 bolts and flywheel.



35. REMOVE PUMP IMPELLER DRIVE PLATE (for Automatic Transmission)


    A072851E02
  1. Using SST, hold the crankshaft pulley.

    SST
    09213-58014  
    09330-00021  



    A114804
  1. Remove the 8 bolts, rear drive plate spacer, pump impeller drive plate and flywheel.



36. REMOVE REAR END PLATE
  1. Remove the bolt and rear end plate.



37. INSTALL ENGINE HANGERS


    A224109E01
  1. Install a No. 1 engine hanger and No. 2 engine hanger with 2 bolts as shown in the illustration.

    Torque:
    for No. 1 engine hanger:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }
    for No. 2 engine hanger:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Engine Hanger
    *2
    No. 2 Engine Hanger

    NOTICE:
    Install the engine hangers with new bolts.

    HINT:
    Part No.
    No. 1 Engine Hanger
    12284-30020
    No. 2 Engine Hanger
    12282-67030
    Bolt
    91552-81014 and 91642-81030



38. REMOVE ENGINE ASSEMBLY


    A098988E01
  1. Attach an engine sling device and hang the engine with a chain block.

  1. Remove the 4 bolts and 4 nuts.

  1. Remove the engine by operating the engine sling device and chain block.



39. INSTALL ENGINE TO ENGINE STAND
  1. Install the engine to an engine stand with bolts.

  1. Remove the 2 bolts and 2 engine hangers.



40. REMOVE ENGINE WIRE
  1. Remove the engine wire from the engine.



41. REMOVE FRONT ENGINE MOUNTING INSULATOR


    A233592E02
  1. Remove the 2 nuts and 2 front engine mounting insulators.
    Text in Illustration 
    *A
    RH Side
    *B
    LH Side



42. REMOVE NO. 1 TIMING BELT COVER


    A015094E01
  1. Remove the 6 bolts, 6 washers and timing belt cover.



43. REMOVE TIMING BELT


    A070549E05
  1. Turn the crankshaft clockwise and align the timing marks as shown in the illustration.
    Text in Illustration 
    *1
    Timing Mark

    HINT:
    If reusing the timing belt, place matchmarks on the timing belt so that it can be installed exactly as before.



    A070550E01
  1. Uniformly loosen and remove the 2 bolts and No. 1 timing belt tensioner.



  1. Remove the timing belt.

    HINT:
    A070551E02
    1. If turning the camshaft while the timing belt is removed, turn the crankshaft 90° counterclockwise as shown in the illustration.
    2. When installing the timing belt, turn the camshaft to align the timing marks, and then turn the crankshaft clockwise to align the timing marks.



44. REMOVE NO. 1 TIMING BELT IDLER SUB-ASSEMBLY


45. REMOVE CRANKSHAFT PULLEY


    A251844E01
  1. Using SST, hold the crankshaft pulley and loosen the pulley bolt.

    SST
    09213-58014  
    09330-00021  



    A251845E01
  1. Using SST, remove the pulley bolt and crankshaft pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply oil or grease to the threads and tip of SST (center bolt) before using it.



46. REMOVE NO. 2 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 2 intercooler support bracket.



47. REMOVE NO. 1 INTERCOOLER SUPPORT BRACKET
  1. Remove the 2 bolts and No. 1 intercooler support bracket.



48. REMOVE COMPRESSOR INLET ELBOW


    A211833
  1. Disconnect the 2 connectors from the turbocharger.

  1. Detach the wire harness clamp.

  1. Remove the 2 nuts, compressor inlet elbow and gasket.



49. REMOVE NO. 1 TURBO INSULATOR


    A255740
  1. Remove the 2 bolts and No. 1 turbo insulator.



50. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A255741
  1. Remove the bolt and No. 1 exhaust manifold heat insulator.



51. REMOVE NO. 1 TURBO WATER HOSE


    A211835
  1. Remove the 2 No. 1 turbo water hoses.



52. REMOVE TURBINE OUTLET ELBOW


    A211836
  1. Remove the 3 nuts, turbine outlet elbow and gasket.



53. REMOVE TURBOCHARGER STAY


    A211837
  1. Remove the 2 bolts, nut and turbocharger stay.



54. DISCONNECT TURBO OIL INLET PIPE SUB-ASSEMBLY


    A098817E03
  1. Remove the 2 bolts, 2 nuts, union bolt, turbo oil inlet pipe and 3 gaskets.

    NOTICE:
    Do not loosen the nut labeled A.



55. REMOVE TURBOCHARGER SUB-ASSEMBLY


    A211839
  1. Remove the 3 nuts, turbocharger and gasket.



56. REMOVE EXHAUST MANIFOLD


    A152664
  1. Remove the 8 nuts, 8 plate washers, 8 collars and exhaust manifold.

  1. Remove the gasket.



57. REMOVE NO. 2 IDLE PULLEY ASSEMBLY
  1. Remove the bolt, pulley plate, No. 2 idle pulley and spacer.



58. REMOVE GENERATOR ASSEMBLY


A111821
  1. Remove the nut and generator wire.

  1. Disconnect the generator connector.

  1. Remove the 2 bolts and generator.



59. REMOVE GENERATOR BRACKET
  1. Remove the bolt and generator bracket.



60. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY


    A098937E01
  1. Remove the 4 bolts and V-ribbed belt tensioner.



61. REMOVE NO. 1 COMPRESSOR MOUNTING BRACKET
  1. Remove the 4 bolts and No. 1 compressor mounting bracket.



62. REMOVE WATER INLET


A250419
  1. Disconnect the wire harness clamp.

  1. Remove the 3 bolts and water inlet.

  1. Remove the bolt and wire harness clamp bracket from the water inlet.



63. REMOVE THERMOSTAT
  1. Remove the thermostat from the cylinder block.

  1. Remove the gasket from the thermostat.



64. REMOVE WATER OUTLET


    A233596
  1. Remove the 2 bolts, water outlet and gasket.



65. REMOVE DIESEL THROTTLE BODY ASSEMBLY
  1. Disconnect the 2 connectors.



    A111832
  1. Remove the 2 bolts, 2 nuts, diesel throttle body and gasket.



66. REMOVE INTAKE MANIFOLD
(Click here)


67. REMOVE GLOW PLUG ASSEMBLY
(Click here)


68. REMOVE OIL FILTER SUB-ASSEMBLY


    A227248E01
  1. Using SST, remove the oil filter.

    SST
    09228-07501  

    HINT:
    Insert the drain hose in the oil filter. Put the disposal container beneath the drain hose to collect the oil from the oil filter.



69. REMOVE FUEL INLET PIPE SUB-ASSEMBLY


    A098969E03
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



70. REMOVE COMMON RAIL ASSEMBLY

NOTICE:
Do not remove the pressure discharge valve and fuel pressure sensor.

  1. Disconnect the 2 connectors.



    A231856
  1. Remove the 2 bolts, common rail and No. 2 intake manifold insulator.



71. REMOVE FUEL SUPPLY PUMP ASSEMBLY


    G036615E01
  1. Remove the bolt and clamp.

  1. Remove the bolt and oil dipstick guide.



    A098969E09
  1. Using a 17 mm union nut wrench, loosen the union nuts and remove the fuel inlet pipe.



    A098895E01
  1. Disconnect the 2 fuel hoses.



    A098896E01
  1. Disconnect the 2 connectors.



    A070710E01
  1. Remove the 4 bolts indicated by the arrows in the illustration.

  1. Remove the No. 2 camshaft timing pulley flange and pump drive shaft pulley.



    A070711E02
  1. Remove the set nut and O-ring while holding the crankshaft pulley using SST.

    SST
    09213-58013  
    09330-00021  



    A098897E01
  1. Loosen the 2 nuts.



    A070714E01
  1. Using SST, disconnect the pump from the injection gear.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)

    NOTICE:
    Apply lubricant to the threads and tip of SST (center bolt) before using it.

  1. Remove the 2 nuts and pump.

    NOTICE:
    1. Do not hold or carry the pump by holding the pipe.
    2. The pump must be kept horizontal.

  1. Remove the O-ring.



72. REMOVE OIL COOLER COVER SUB-ASSEMBLY
  1. Disconnect the oil pressure switch connector and wire harness.



    A038741E01
  1. Remove the 13 bolts, 2 nuts and oil cooler cover.



73. REMOVE TIMING GEAR COVER INSULATOR (w/ EGR Cooler)


    A148171
  1. Remove the bolt and timing gear cover insulator.



74. REMOVE VACUUM PUMP ASSEMBLY


    A098930E01
  1. Remove the 2 nuts, vacuum pump and 2 O-rings.



75. REMOVE VANE PUMP ASSEMBLY


    A233594
  1. Remove the 2 nuts, vane pump and O-ring.



76. REMOVE CRANKSHAFT POSITION SENSOR
  1. Disconnect the crankshaft position sensor connector.



  1. Detach the 3 clips, and the bolt and crankshaft position sensor.


    A253484



77. REMOVE CAMSHAFT POSITION SENSOR


A112046
  1. Disconnect the camshaft position sensor connector.

  1. Remove the bolt and camshaft position sensor.



78. REMOVE ENGINE COOLANT TEMPERATURE SENSOR


A252686
  1. Disconnect the engine coolant temperature sensor connector.

  1. Remove the engine coolant temperature sensor.

  1. Remove the gasket from the engine coolant temperature sensor.



79. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH


    A233593E02
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.
    Text in Illustration 
    *A
    RH Side
    *B
    LH Side



80. REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH
  1. Remove the 4 bolts and front No. 1 engine mounting bracket.