Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

DTC    P0405    Exhaust Gas Recirculation Sensor "A" Circuit Low

DTC    P0406    Exhaust Gas Recirculation Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

The EGR valve position sensor is mounted on the EGR valve and is used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.

P0405 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch to ON for 5 seconds
EGR valve position sensor output voltage is below 0.1 V for more than 5 seconds (1 trip detection logic).
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

P0406 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch to ON for 5 seconds
EGR valve position sensor output voltage is more than 4.9 V for higher than 5 seconds (1 trip detection logic).
  1. Open or short in EGR valve position sensor circuit
  2. EGR valve position sensor
  3. ECM

MONITOR DESCRIPTION

When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit and illuminates the MIL.

WIRING DIAGRAM


A154317E11


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK TERMINAL VOLTAGE (EGR VALVE POSITION SENSOR CONNECTOR)


    A253299E04
  1. Disconnect the EGR valve position sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E26-1 (VC) - E26-2 (E2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to EGR Valve Position Sensor)

  1. Reconnect the electric vacuum regulating valve assembly connector.



NG
Go to step 3
OK


2.INSPECT EGR VALVE POSITION SENSOR
  1. Inspect the EGR valve position sensor (Click here).



NG
Go to step 5
OK


3.CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM)
  1. Disconnect the EGR valve position sensor connector.

  1. Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E26-1 (VC) - E7-18 (VC)
    Always
    Below 1 Ω
    E26-3 (EGLS) - E6-33 (EGLS)
    Always
    Below 1 Ω
    E26-2 (E2) - E7-28 (E2)
    Always
    Below 1 Ω
    E26-1 (VC) or E7-18 (VC) - Body ground
    Always
    10 kΩ or higher
    E26-3 (EGLS) or E6-33 (EGLS) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the electric vacuum regulating valve assembly connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


4.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

5.REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY
  1. Replace the electric EGR control valve assembly (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON for 5 seconds or more.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END