Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for i-ART)

DTC    P0201    Injector Circuit / Open - (Cylinder 1)

DTC    P0202    Injector Circuit / Open - (Cylinder 2)

DTC    P0203    Injector Circuit / Open - (Cylinder 3)

DTC    P0204    Injector Circuit / Open - (Cylinder 4)

DTC    P062D    No. 1 Fuel Injector Driver Circuit Performance

for Preparation Click here


DESCRIPTION

The injector driver (EDU) delivers drive signals to the injector assembly using the DC/DC converter, which provides a high-voltage and quick-charging system.
Soon after the injector driver (EDU) receives an injection command (IJT) signal from the ECM, the injector driver (EDU) responds to the command with an injector injection confirmation (IJF) signal when the current is applied to the injector.

A210270E24


P0201, P0202, P0203, P0204 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 seconds
Open or short in injector circuit occurs a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
  1. Open or short in injector driver circuit
  2. Injector assembly
  3. Injector driver
  4. ECM

P062D 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Idling for 5 seconds
Inconsistency in the injection waveforms between the injector driver and ECM while the engine is running a certain number of times (a maximum of approx. 0.5 seconds).
(1 trip detection logic)
  1. Open or short in injector driver circuit
  2. Injector assembly
  3. Injector driver
  4. ECM

MONITOR DESCRIPTION

  1. P0201, P0202, P0203, P0204:
    The ECM compares injection command (#1 to #4) signals and injection confirmation (INJF) signals for each cylinder. If the ECM determines that a cylinder has a malfunction, DTC P0201, P0202, P0203 or P0204 will be stored.
  1. P062D:
    The ECM continuously monitors both injection command (IJT) signals and injection confirmation (IJF) signals. This DTC will be stored if the ECM determines that the number of IJT signals and IJF signals are inconsistent.
    The fuel injectors are grounded over a Field Effect Transistor (FET) and a serial resistor. This resistor creates a voltage drop, which is monitored by the injector driver (EDU) (injector drive circuit) in relation to the current drawn by the injector assembly. When the injector current becomes too high, the voltage drop over the resistor exceeds a specified level and no IJF signal for that cylinder is sent to the ECM.
    After the engine is started, when there is no injection confirmation (IJF) signal from the injector driver (EDU) to the ECM even though the ECM sends injection command (IJT) signals to the injector driver (EDU), DTC P062D is stored.
    If this DTC is stored, the ECM enters fail-safe mode and limits engine power or stops the engine. The fail-safe mode continues until the ignition switch is turned off.

    A145849E05


WIRING DIAGRAM


A279707E02


A279708E02


INSPECTION PROCEDURE

CAUTION:
Make sure to perform work on high voltage circuits with the ignition switch off.

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK ENGINE CRANKING CONDITION
  1. Check the engine cranking condition.

    Result 
    Result
    Proceed to
    Engine does not start*1
    A
    Engine starts, but idling is rough*2
    B
    Except above
    C

    HINT:
    1. *1: Once DTC P062D is cleared, it is not stored again even when the engine does not start due to a malfunction in the injector driver (EDU).
      When the engine cannot be started due to a malfunction in the injector driver (EDU), the value for "Fuel Press" is higher than the value for "Target Common Rail Pressure".
    2. *2: DTC P0201, P0202, P0203, P0204 and P062D are stored at this time.



B
Go to step 6

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT ECM


    A255625E09
  1. Check the waveform of the ECM connectors using an oscilloscope.

    OK:
    Tester Connection
    Condition
    Specified Condition
    E29-21 (#1) - E28-6 (E1)
    Cranking
    Correct waveform is as shown
    E29-22 (#2) - E28-6 (E1)
    Cranking
    Correct waveform is as shown
    E29-23 (#3) - E28-6 (E1)
    Cranking
    Correct waveform is as shown
    E29-24 (#4) - E28-6 (E1)
    Cranking
    Correct waveform is as shown

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



NG
Go to step 10
OK


3.CHECK TERMINAL VOLTAGE INJECTOR DRIVER POWER SOURCE


    A204910E32
  1. Disconnect the injector driver connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    I17-2 (+B) - I17-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Injector Driver)

  1. Reconnect the injector driver connectors.



NG
Go to step 13
OK


4.CHECK HARNESS AND CONNECTOR (INJECTOR DRIVER - ECM)
  1. Disconnect the injector driver connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    I19-7 (#10) - E29-21 (#1)
    Always
    Below 1 Ω
    I19-3 (#20) - E29-22 (#2)
    Always
    Below 1 Ω
    I19-6 (#30) - E29-23 (#3)
    Always
    Below 1 Ω
    I19-4 (#40) - E29-24 (#4)
    Always
    Below 1 Ω
    I19-8 (INJF) - E29-20 (INJF)
    Always
    Below 1 Ω
    I19-7 (#10) or E29-21 (#1) - Body ground
    Always
    10 kΩ or higher
    I19-3 (#20) or E29-22 (#2) - Body ground
    Always
    10 kΩ or higher
    I19-6 (#30) or E29-23 (#3) - Body ground
    Always
    10 kΩ or higher
    I19-4 (#40) or E29-24 (#4) - Body ground
    Always
    10 kΩ or higher
    I19-8 (INJF) or E29-20 (INJF) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reconnect the ECM connector.



NG
Go to step 13
OK


5.REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).



NEXT
Go to step 14

6.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds.

  1. Start the engine and idle it for 30 seconds.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Check the DTCs output on the GTS.

    HINT:
    1. The cylinder with the malfunctioning injector assembly can be determined based on the output DTCs.
    2. If DTC P0201 is output, check the No. 1 injector assembly circuit.
    3. If DTC P0202 is output, check the No. 2 injector assembly circuit.
    4. If DTC P0203 is output, check the No. 3 injector assembly circuit.
    5. If DTC P0204 is output, check the No. 4 injector assembly circuit.


NEXT


7.INSPECT INJECTOR DRIVER


    A279710E02
  1. Disconnect the injector assembly connectors for all cylinders.

    NOTICE:
    If only the injector assembly connector of the malfunctioning cylinder is disconnected, the engine will start and there will be rough idling. Therefore, disconnect all injector assembly connectors before inspecting the waveform.

  1. Start the engine.

  1. Check the waveform of the injector assembly connectors using an oscilloscope.

    OK:
    Tester Connection
    Condition
    Specified Condition
    F31-3 (#1) - F31-6 (#10)
    Cranking
    Voltage increases by 50 V or more
    F32-3 (#2) - F32-6 (#20)
    Cranking
    Voltage increases by 50 V or more
    F33-3 (#3) - F33-6 (#30)
    Cranking
    Voltage increases by 50 V or more
    F34-3 (#4) - F34-6 (#40)
    Cranking
    Voltage increases by 50 V or more

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector)



NG
Go to step 11
OK


8.REPLACE INJECTOR ASSEMBLY (RELEVANT CYLINDER)
  1. Replace the injector assembly of the cylinder relevant to the DTC (Click here).

    NOTICE:
    1. When replacing the injector assembly for a cylinder, always be sure to use a new injection pipe.
    2. Follow the procedure in the repair manual and temporarily install the injection pipes and nozzle leakage pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.
    3. If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.
    4. If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.
    5. If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe may become incomplete, resulting in a fuel leak.


NEXT


9.BLEED AIR FROM FUEL SYSTEM
  1. Bleed the air from the fuel system .



NEXT
Go to step 14

10.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 14

11.CHECK HARNESS AND CONNECTOR (INJECTOR ASSEMBLY - INJECTOR DRIVER)
  1. Disconnect the injector assembly connectors.

  1. Disconnect the injector driver connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    F31-6 (#10) - I18-1 (IJ1+)
    Always
    Below 1 Ω
    F31-3 (#1) - I18-4 (IJ1-)
    Always
    Below 1 Ω
    F32-6 (#20) - I18-3 (IJ2+)
    Always
    Below 1 Ω
    F32-3 (#2) - I18-6 (IJ2-)
    Always
    Below 1 Ω
    F33-6 (#30) - I17-1 (IJ3+)
    Always
    Below 1 Ω
    F33-3 (#3) - I17-3 (IJ3-)
    Always
    Below 1 Ω
    F34-6 (#40) - I18-2 (IJ4+)
    Always
    Below 1 Ω
    F34-3 (#4) - I18-5 (IJ4-)
    Always
    Below 1 Ω
    F31-6 (#10) or I18-1 (IJ1+) - Body ground
    Always
    10 kΩ or higher
    F31-3 (#1) or I18-4 (IJ1-) - Body ground
    Always
    10 kΩ or higher
    F32-6 (#20) or I18-3 (IJ2+) - Body ground
    Always
    10 kΩ or higher
    F32-3 (#2) or I18-6 (IJ2-) - Body ground
    Always
    10 kΩ or higher
    F33-6 (#30) or I17-1 (IJ3+) - Body ground
    Always
    10 kΩ or higher
    F33-3 (#3) or I17-3 (IJ3-) - Body ground
    Always
    10 kΩ or higher
    F34-6 (#40) or I18-2 (IJ4+) - Body ground
    Always
    10 kΩ or higher
    F34-3 (#4) or I18-5 (IJ4-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector assembly connectors.

  1. Reconnect the injector driver connectors.



NG
Go to step 13
OK


12.REPLACE INJECTOR DRIVER
  1. Replace the injector driver (Click here).



NEXT
Go to step 14

13.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off for 30 seconds or more.

  1. Start the engine and idle it for 5 seconds.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Confirm that the DTC is not output again.


NEXT

END