DTC P2120 Throttle / Pedal Position Sensor / Switch "D" Circuit |
DTC P2122 Throttle / Pedal Position Sensor / Switch "D" Circuit Low Input |
DTC P2123 Throttle / Pedal Position Sensor / Switch "D" Circuit High Input |
DTC P2125 Throttle / Pedal Position Sensor / Switch "E" Circuit |
DTC P2127 Throttle / Pedal Position Sensor / Switch "E" Circuit Low Input |
DTC P2128 Throttle / Pedal Position Sensor / Switch "E" Circuit High Input |
DTC P2138 Throttle / Pedal Position Sensor / Switch "D" / "E" Voltage Correlation |

| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Condition (a) continues for 0.5 seconds (1 trip detection logic): (a) VPA is below 0.4 V and VPA2 is more than 2.7 deg, or VPA is higher than 4.8 V. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic): (a) VPA is below 0.4 V. (b) VPA2 is more than 2.7 deg. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Condition (a) continues for 2.0 seconds (1 trip detection logic): (a) VPA is higher than 4.8 V. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Condition (a) continues for 0.5 seconds (1 trip detection logic): (a) VPA2 is below 1.2 V and VPA is more than 2.7 deg, or VPA2 is higher than 4.8 V and VPA is higher than 0.4 V but below 3.45 V. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Conditions (a) and (b) continue for 0.5 seconds (1 trip detection logic): (a) VPA2 is below 1.2 V. (b) VPA is more than 2.7 deg. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Conditions (a) and (b) continue for 2.0 seconds (1 trip detection logic): (a) VPA2 is higher than 4.8 V. (b) VPA is higher than 0.4 V but below 3.45 V. |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
Ignition switch ON
| Conditions (a) or (b) continue for 2.0 seconds (1 trip detection logic): (a) The difference between VPA and VPA2 is less than 0.02 V. (b) VPA is below 0.4 V and VPA2 is below 1.2 V. |
|
| DTC No. | Data List |
| P2120 |
|
| P2122 | |
| P2123 | |
| P2125 | |
| P2127 | |
| P2128 | |
| P2138 |

| 1.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION) |
![]() |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Accel Sens. No.1 Volt % and Accel Sens. No.2 Volt %.
Read the values.
| Accelerator Pedal | Accel Sens. No.1 Volt % | Accel Sens. No.2 Volt % |
| Released | 10 to 22% | 24 to 40% |
| Depressed | 52 to 90% | 68 to 99% |
| *1 | Accelerator Pedal Assembly |
| *a | Depressed |
| *b | Released |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (ACCELERATOR PEDAL POSITION SENSOR - ECM) |
Disconnect the accelerator pedal position sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A22-1 (VCP2) - E31-4 (VCP2) | Always | Below 1 Ω |
| A22-2 (EPA2) - E31-3 (EPA2) | Always | Below 1 Ω |
| A22-3 (VPA2) - E32-1 (VPA2) | Always | Below 1 Ω |
| A22-4 (VCPA) - E31-6 (VCPA) | Always | Below 1 Ω |
| A22-5 (EPA) - E31-5 (EPA) | Always | Below 1 Ω |
| A22-6 (VPA) - E32-2 (VPA) | Always | Below 1 Ω |
| A22-1 (VCP2) or E31-4 (VCP2) - Body ground | Always | 10 kΩ or higher |
| A22-3 (VPA2) or E32-1 (VPA2) - Body ground | Always | 10 kΩ or higher |
| A22-4 (VCPA) or E31-6 (VCPA) - Body ground | Always | 10 kΩ or higher |
| A22-6 (VPA) or E32-2 (VPA) - Body ground | Always | 10 kΩ or higher |
Reconnect the accelerator pedal position sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.INSPECT ECM TERMINAL VOLTAGE (VCPA AND VCP2 TERMINALS) |
![]() |
Disconnect the accelerator pedal position sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A22-4 (VCPA) - A22-5 (EPA) | Ignition switch ON | 4.5 to 5.5 V |
| A22-1 (VCP2) - A22-2 (EPA2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Accelerator Pedal Position Sensor) |
Reconnect the accelerator pedal position sensor connector.
|
| ||||
| OK | |
| 4.REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY |
Replace the accelerator pedal sensor assembly (Click here).
|
| ||||
| 5.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 6.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off and leave the vehicle for 30 seconds.
Turn the ignition switch to ON.
Fully release the accelerator pedal for 3 seconds or more, then depress it partway for 3 seconds or more, and then fully depress it for 3 seconds or more.
Confirm that the DTC is not output again.
| NEXT | ||
| ||