Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (w/ EGR Cooler)

ECD SYSTEM (w/ EGR Cooler) > VC Output Circuit

for Preparation Click here


DESCRIPTION

The VC voltage (5 V) is generated in the ECM. The voltage is used to supply power to the throttle body assembly, turbo pressure sensor, accelerator position sensor and fuel pressure sensor.

WIRING DIAGRAM


A149982E34


A149983E37


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

1.CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch ON.

    Result 
    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B



B
SYSTEM OK
A


2.CHECK CONNECTION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and tester on.

  1. Check the communication between the intelligent tester and ECM.
    Result 
    Condition
    Proceed to
    Communication is not possible
    A
    Communication is possible
    B



B
GO TO MIL CIRCUIT (Click here)
A


3.CHECK MIL (THROTTLE POSITION SENSOR)
  1. Disconnect the throttle position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the throttle position sensor connector.



B
REPLACE DIESEL THROTTLE BODY ASSEMBLY (Click here)
A


4.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
  1. Disconnect the manifold absolute pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the manifold absolute pressure sensor connector.



B
REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
A


5.CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the accelerator position sensor connector.



B
REPLACE ACCELERATOR PEDAL ROD ASSEMBLY (Click here)
A


6.CHECK MIL (FUEL PRESSURE SENSOR)
  1. Disconnect the fuel pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the fuel pressure sensor connector.



B
REPLACE COMMON RAIL ASSEMBLY (Click here)
A


7.CHECK MIL (EGR VALVE POSITION SENSOR)
  1. Disconnect the EGR valve position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.
    Result 
    Condition
    Proceed to
    MIL does not illuminate
    A
    MIL illuminates
    B

  1. Reconnect the EGR valve position sensor connector.



B
REPLACE ELECTRIC EGR CONTROL VALVE ASSEMBLY (Click here)
A


8.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
  1. Disconnect the throttle position sensor connector.

  1. Disconnect the manifold absolute pressure sensor connector.

  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the EGR valve position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E7-18 (VC) - Body ground
    Always
    10 kΩ or higher
    E6-2 (VCS) - Body ground
    Always
    10 kΩ or higher
    E4-26 (VCPA) - Body ground
    Always
    10 kΩ or higher
    E4-27 (VCP2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the throttle position sensor connector.

  1. Reconnect the manifold absolute pressure sensor connector.

  1. Reconnect the fuel pressure sensor connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the EGR valve position sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)