DTC P0046 Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance |
DTC P0047 Turbocharger/Supercharger Boost Control "A" Circuit Low |
DTC P0048 Turbocharger/Supercharger Boost Control "A" Circuit High |
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| Ignition switch ON for 5 seconds | Either condition is met when the motor is operating (1 trip detection logic):
|
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 2 seconds after engine is started, race engine for 1 second | The DC motor duty ratio is 80% or more and the motor current is 0.5 A or less for 3 seconds or more (1 trip detection logic). |
|
| DTC Detection Drive Pattern | DTC Detection Condition | Trouble Area |
| 2 seconds after engine is started, race engine for 1 second | Overcurrent is detected 25 times or more (0.4 seconds or more) (1 trip detection logic). |
|

| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0046, P0047 AND/OR P0048) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| P0046, P0047 and/or P0048 is output | A |
| P0046, P0047 and/or P0048 and other DTCs are output | B |
|
| ||||
| A | |
| 2.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR OPERATION) |
Inspect the turbocharger sub-assembly .
|
| ||||
| NG | |
| 3.INSPECT TURBOCHARGER SUB-ASSEMBLY (DC MOTOR RESISTANCE) |
![]() |
Disconnect the DC motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 (M-) - 2 (M+) | Always | 1 to 100 Ω |
| *a | Component without harness connected (DC Motor) |
Reconnect the DC motor connector.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (DC MOTOR - ECM) |
Disconnect the DC motor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| T10-1 (M-) - E28-14 (M-) | Always | Below 1 Ω |
| T10-2 (M+) - E28-15 (M+) | Always | Below 1 Ω |
| T10-1 (M-) or E28-14 (M-) - Body ground | Always | 10 kΩ or higher |
| T10-2 (M+) or E28-15 (M+) - Body ground | Always | 10 kΩ or higher |
Reconnect the DC motor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 5.REPLACE ECM |
Replace the ECM (Click here).
|
| ||||
| 6.REPLACE TURBOCHARGER SUB-ASSEMBLY |
Replace the turbocharger sub-assembly (Click here).
|
| ||||
| 7.REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON for 5 seconds or more.
2 seconds after the engine is started, race the engine for 1 second.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||