Home › ENGINE · 1KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM (for i-ART)

DTC    P2564    Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low

DTC    P2565    Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High

for Preparation Click here


DESCRIPTION

The variable nozzle vane type turbocharger consists primarily of a compressor wheel, turbine wheel, nozzle vane, unison ring, DC motor and nozzle vane position sensor.
The nozzle vane position sensor consists of a Hall IC and a magnetic yoke that rotates in unison with the movement of the linkage that actuates the nozzle vane. The nozzle vane position sensor converts the changes in the magnetic flux that are caused by the rotation of the DC motor (hence, the rotation of the magnetic yoke) into electric signals, and outputs them to the ECM. The ECM determines the actual nozzle vane position from the electric signals in order to calculate the target nozzle vane position.

A221597E02


P2564 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VNA voltage is 0.1 V or less for 2.1 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. ECM

P2565 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 1 second
VNA voltage is 4.9 V or higher for 2.1 seconds (1 trip detection logic).
  1. Nozzle vane position sensor (turbocharger sub-assembly)
  2. Open or short in nozzle vane position sensor circuit
  3. ECM

HINT:
If DTC P2564 and/or P2565 is stored due to the nozzle vane being stuck open, the following symptoms may appear:
  1. - Lack of power
  2. - Vehicle surge or hesitation under light or medium load


WIRING DIAGRAM


A221590E16


INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

1.CHECK OTHER DTC OUTPUT (IN ADDITION TO DTC P2564 AND P2565)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON and turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P2564 and/or P2565 is output
    A
    P2564 and/or P2565 and other DTCs are output
    B



B
GO TO DTC CHART (Click here)
A


2.CHECK HARNESS AND CONNECTOR (ECM - NOZZLE VANE POSITION SENSOR)
  1. Disconnect the nozzle vane position sensor connector.

  1. Disconnect the ECM.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    T11-1 (VTA1) - E30-11 (VNA)
    Always
    Below 1 Ω
    T11-2 (VNE2) - E30-5 (VNE2)
    Always
    Below 1 Ω
    T11-3 (VNVC) - E30-17 (VNVC)
    Always
    Below 1 Ω
    T11-1 (VTA1) or E30-11 (VNA) - Body ground
    Always
    10 kΩ or higher
    T11-3 (VNVC) or E30-17 (VNVC) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the nozzle vane position sensor connector.

  1. Reconnect the ECM connector.



NG
Go to step 6
OK


3.INSPECT ECM (VNVC VOLTAGE)


    A258708E49
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E30-17 (VNVC) - E30-5 (VNE2)
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)



OK
Go to step 5
NG


4.REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 7

5.REPLACE TURBOCHARGER SUB-ASSEMBLY (NOZZLE VANE POSITION SENSOR)
  1. Replace the turbocharger sub-assembly (Click here).



NEXT
Go to step 7

6.REPAIR OR REPLACE HARNESS OR CONNECTOR
  1. Repair or replace the harness or connector.


NEXT


7.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the GTS to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch off and wait for 30 seconds or more.

  1. Turn the ignition switch to ON and wait for 10 seconds or more.

  1. Confirm that the DTC is not output again.

    HINT:
    Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.

    1. Enter the following menus: Powertrain / Engine / Utility / All Readiness.

    2. Input DTC P2564 and/or P2565.

    3. Check that STATUS is NORMAL. If STATUS is INCOMPLETE or N/A, idle the engine.


NEXT

END