Home › ENGINE · 2KD-FTV › ENGINE CONTROL SYSTEM › ECD SYSTEM

ECD SYSTEM > Injector Circuit

for Preparation Click here


DESCRIPTION

The injector driver drives the injectors at high speeds with a high-voltage DC/DC converter. The ECM constantly monitors the injector driver and stops the engine if an abnormal condition is detected.

WIRING DIAGRAM

Refer to DTC P0200 .

INSPECTION PROCEDURE

NOTICE:
  1. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
  2. Inspect the fuses of circuits related to this system before performing the following inspection procedure.

1.CHECK INJECTOR DRIVER (POWER SOURCE)


    A221614E48
  1. Disconnect the injector driver connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for Manual Transmission 
    Tester Connection
    Switch Condition
    Specified Condition
    I14-2 (+B) - I14-3 (GND)
    Ignition switch ON
    11 to 14 V

    Standard Voltage:
    for Automatic Transmission 
    Tester Connection
    Switch Condition
    Specified Condition
    I21-2 (+B) - I21-3 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *A
    for Manual Transmission
    *B
    for Automatic Transmission
    *a
    Front view of wire harness connector
    (to Injector Driver)

  1. Reconnect the injector driver connectors.



NG
Go to step 2
OK

REPLACE INJECTOR DRIVER (Click here)  

2.INSPECT NO. 1 INTEGRATION RELAY (EDU)
  1. Inspect the No. 1 integration relay (EDU) (Click here).



NG
REPLACE NO. 1 INTEGRATION RELAY (EDU)
OK


3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY [EDU] - INJECTOR DRIVER)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the injector driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    for Manual Transmission 
    Tester Connection
    Condition
    Specified Condition
    I14-2 (+B) - 1J-8
    Always
    Below 1 Ω
    I14-3 (GND) - Body ground
    Always
    Below 1 Ω
    I14-2 (+B) or 1J-8 - Body ground
    Always
    10 kΩ or higher


    Standard Resistance:

    for Automatic Transmission 
    Tester Connection
    Condition
    Specified Condition
    I21-2 (+B) - 1J-8
    Always
    Below 1 Ω
    I21-3 (GND) - Body ground
    Always
    Below 1 Ω
    I21-2 (+B) or 1J-8 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the injector driver connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
  1. Remove the No. 1 integration relay from the engine room relay block and junction block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Tester Connection
    Condition
    Specified Condition
    E4-10 (IREL) - 1J-7
    Always
    Below 1 Ω
    E4-10 (IREL) or 1J-7 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reinstall the No. 1 integration relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)