Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

DTC    B15C3    Speaker Output Short


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
Either condition is met:
  1. A malfunction occurs in the navigation receiver assembly internal power IC.
  2. A DC offset occurs in +/- speaker output.
  1. Speakers
  2. Navigation receiver assembly
  3. Harness or connector

WIRING DIAGRAM


C240170E50


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Disconnect the N8 and N7 navigation receiver assembly connectors.

  1. Clear the DTC (Click here).

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)
OK


2.CHECK FOR DTC
  1. Disconnect the N8 navigation receiver assembly connector.

  1. Clear the DTC (Click here).

  1. Check if DTC B15C3 is output.

    OK:
    DTC B15C3 is not output.



NG
Go to step 7
OK


3.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the N8 navigation receiver assembly connector.

  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N8-1 (FR+) - T25-4
    Always
    Below 1 Ω
    N8-5 (FR-) - T25-2
    N8-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    N8-5 (FR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N8-2 (FL+) - T24-4
    Always
    Below 1 Ω
    N8-6 (FL-) - T24-2
    N8-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    N8-6 (FL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH
  2. *2: for LH
  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.

  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    T25-3 - S16-1
    Always
    Below 1 Ω
    T25-1 - S16-2
    T25-3 - Body ground
    Always
    10 kΩ or higher
    T25-1 - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    T24-3 - S15-1
    Always
    Below 1 Ω
    T24-1 - S15-2
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1 - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the front No. 1 speaker assembly connector.

  1. Inspect the front No. 1 speaker assembly connector (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Temporarily replace the front No. 2 speaker assembly with a new or normally functioning one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the speaker connectors to the speakers.
    2. When there is a possibility that either the right or left speaker is defective, inspect by interchanging the right one with the left one.

    Result 
    Result
    Proceed to
    Malfunction does not disappear
    A
    Malfunction disappears
    B



B
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
A

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)  

7.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
  1. Disconnect the N7 navigation receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

    1. *1: for RH
    2. *2: for LH

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH 
    Tester Connection
    Condition
    Specified Condition
    N7-1 (RR+) - S18-1
    Always
    Below 1 Ω
    N7-3 (RR-) - S18-2
    N7-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    N7-3 (RR-) - Body ground
    for LH 
    Tester Connection
    Condition
    Specified Condition
    N7-2 (RL+) - S17-1
    Always
    Below 1 Ω
    N7-6 (RL-) - S17-2
    N7-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    N7-6 (RL-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT REAR SPEAKER ASSEMBLY
  1. Disconnect the rear speaker assembly connector.

  1. Inspect the rear speaker assembly connector (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE NAVIGATION RECEIVER ASSEMBLY (Click here)