Home › BODY ELECTRICAL › AUDIO / VISUAL › AUDIO AND VISUAL SYSTEM (for Radio and Display Type)

DTC    B15C3    Speaker Output Short

for Preparation Click here


DESCRIPTION

This DTC is stored when a malfunction occurs in the speakers.

DTC No.
DTC Detection Condition
Trouble Area
B15C3
A short is detected in the speaker output circuit.
  1. Speakers
  2. Radio and display receiver assembly
  3. Harness or connector

WIRING DIAGRAM


C240170E53


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Disconnect the R20 and R19 radio and display receiver assembly connectors.

  1. Clear the DTCs (Click here).

  1. Check if DTC B15C3 is output (Click here).

    OK:
    DTC B15C3 is not output.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK


2.CHECK FOR DTC
  1. Reconnect the R19 radio and display receiver assembly connector.

  1. Clear the DTC (Click here).

  1. Check if DTC B15C3 is output (Click here).

    OK:
    DTC B15C3 is not output.

    Result 
    Result
    Proceed to
    Malfunction in front speaker area
    A
    Malfunction in rear speaker area
    B



B
Go to step 7
A


3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - FRONT NO. 2 SPEAKER ASSEMBLY)
  1. Disconnect the R20 radio and display receiver assembly connector.

  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.

    1. *1: for RH Side
    2. *2: for LH Side

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    R20-1 (FR+) - T25-4
    Always
    Below 1 Ω
    R20-5 (FR-) - T25-2
    Always
    Below 1 Ω
    R20-1 (FR+) - Body ground
    Always
    10 kΩ or higher
    R20-5 (FR-) - Body ground
    Always
    10 kΩ or higher
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    R20-2 (FL+) - T24-4
    Always
    Below 1 Ω
    R20-6 (FL-) - T24-2
    Always
    Below 1 Ω
    R20-2 (FL+) - Body ground
    Always
    10 kΩ or higher
    R20-6 (FL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER ASSEMBLY - FRONT NO. 1 SPEAKER ASSEMBLY)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the S16*1 and/or S15*2 front No. 1 speaker assembly connector.

  1. Disconnect the T25*1 and/or T24*2 front No. 2 speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side:
    Tester Connection
    Condition
    Specified Condition
    T25-3 - S16-1
    Always
    Below 1 Ω
    T25-1 - S16-2
    Always
    Below 1 Ω
    T25-3 - Body ground
    Always
    10 kΩ or higher
    T25-1 - Body ground
    Always
    10 kΩ or higher
    for LH Side:
    Tester Connection
    Condition
    Specified Condition
    T24-3 - S15-1
    Always
    Below 1 Ω
    T24-1 - S15-2
    Always
    Below 1 Ω
    T24-3 - Body ground
    Always
    10 kΩ or higher
    T24-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5.INSPECT FRONT NO. 1 SPEAKER ASSEMBLY
  1. Remove the front No. 1 speaker assembly (Click here).

  1. Inspect the front No. 1 speaker assembly (Click here).



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


6.CHECK FRONT NO. 2 SPEAKER ASSEMBLY
  1. Replace the front No. 2 speaker with a known good one (Click here).

  1. Check that the malfunction disappears.

    HINT:
    1. Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
    2. When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
    3. Perform the above inspection on both LH and RH sides.

    OK:
    Malfunction disappears.



NG
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)
OK

END (FRONT NO. 2 SPEAKER ASSEMBLY IS DEFECTIVE) 

7.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - REAR SPEAKER ASSEMBLY)
  1. *1: for RH Side
  2. *2: for LH Side
  1. Disconnect the R19 radio and display receiver assembly connector.

  1. Disconnect the S18*1 and/or S17*2 rear speaker assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for RH Side 
    Tester Connection
    Condition
    Specified Condition
    R19-1 (RR+) - S18-1
    Always
    Below 1 Ω
    R19-3 (RR-) - S18-2
    Always
    Below 1 Ω
    R19-1 (RR+) - Body ground
    Always
    10 kΩ or higher
    R19-3 (RR-) - Body ground
    Always
    10 kΩ or higher
    for LH Side 
    Tester Connection
    Condition
    Specified Condition
    R19-2 (RL+) - S17-1
    Always
    Below 1 Ω
    R19-6 (RL-) - S17-2
    Always
    Below 1 Ω
    R19-2 (RL+) - Body ground
    Always
    10 kΩ or higher
    R19-6 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.INSPECT REAR SPEAKER ASSEMBLY
  1. Remove the rear speaker assembly (Click here)

  1. Inspect the rear speaker assembly (Click here).



NG
REPLACE REAR SPEAKER ASSEMBLY (Click here)
OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY (Click here)