Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (w/ VSC)

CAN COMMUNICATION SYSTEM (w/ VSC) > ECM Communication Stop Mode

for Preparation Click here


DESCRIPTION


Detection Item
Symptom
Trouble Area
ECM Communication Stop Mode
Either condition is met:
  1. "ECM (Engine)" is not displayed on the "Bus Check" screen.
  2. "ECM Communication Stop Mode" in "DTC Communication Table" applies.
  1. Power source or inside of ECM
  2. ECM

WIRING DIAGRAM


C247095E01


C236846E03


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)


  1. for 1GR-FE:


    C247206E01


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -
    1. Disconnect the E14, E15 and E17 ECM connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      E14-3 (BATT) - Body ground
      Always
      11 to 14 V
      E14-1 (+B) - Body ground
      Battery positive (+) voltage applied to terminal E14-8 (MREL)
      11 to 14 V
      E14-2 (+B2) - Body ground
      Battery positive (+) voltage applied to terminal E14-8 (MREL)
      11 to 14 V
      E14-9 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E17-1 (E1) - Body ground
      Always
      Below 1 Ω
      E15-7 (E01) - Body ground
      Always
      Below 1 Ω
      E15-6 (E02) - Body ground
      Always
      Below 1 Ω



  1. for 1KD-FTV:


    C236880E02


    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)
    -
    -
    1. Disconnect the E4, E5, E6 and E7 ECM connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      E5-2 (BATT) - Body ground
      Always
      11 to 14 V
      E4-1 (+B) - Body ground
      Battery positive (+) voltage applied to terminal E4-8 (MREL)
      11 to 14 V
      E4-9 (IGSW) - Body ground
      Ignition switch ON
      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      E6-7 (E1) - Body ground
      Always
      Below 1 Ω
      E7-7 (E01) - Body ground
      Always
      Below 1 Ω
      E7-6 (E02) - Body ground
      Always
      Below 1 Ω

Result 
Result
Proceed to
OK (for 1GR-FE)
A
OK (for 1KD-FTV)
B
NG
C


B
REPLACE ECM (Click here)

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)