Home › Drivetrain › RC61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSMISSION ASSEMBLY
RM33K0E _52 Drivetrain _043593 RC61F MANUAL TRANSMISSION / TRANSAXLE _0212115 MANUAL TRANSMISSION ASSEMBLY A

RC61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 2.INSTALL WIRING HARNESS CLAMP BRACKET

a.
C324646C03
0.385,1.729 0.854,1.729 0.854,1.729 1.052,1.438 true 0.167,1.667 0.479,1.823 0.313,0.156 10 false *A
*A w/ Intelligent Manual Transmission Switch


Install the 8 bolts and 6 wiring harness clamp brackets to the manual transmission assembly.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


Hide 33019C 3.INSTALL TRANSMISSION BREATHER SUB-ASSEMBLY

a.
C324647

Install the 2 bolts and 2 brackets to the manual transmission assembly.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


b.
C324643

Install the transmission breather sub-assembly to the control shift lever retainer sub-assembly.


c.

Attach the 4 breather hose clamps.


Hide 4.INSTALL MANUAL TRANSMISSION ASSEMBLY

a.
C324649

Install the manual transmission assembly with the 5 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 5.CONNECT WIRE HARNESS

a.
C328313

w/ Intelligent Manual Transmission Switch:

i.

Attach the 7 wire harness clamps.


ii.

Install the bolt.


iii.

Connect the 3 connectors and wire harness.



b.
C328312

w/o Intelligent Manual Transmission Switch:

i.

Attach the 5 wire harness clamps.


ii.

Install the bolt.


iii.

Connect the 2 connectors and wire harness.



Hide 12371A 6.INSTALL REAR ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the manual transmission assembly with the 4 bolts.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 51204 7.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C325680

Install the No. 3 frame crossmember sub-assembly with the 4 nuts and 4 bolts.

Torque:
57 N*m (581 kgf*cm, 42 ft.*lbf)


b.
C338961

Install the 4 bolts to the No. 3 frame crossmember sub-assembly.

Torque:
18.5 N*m (189 kgf*cm, 14 ft.*lbf)


Hide 8.CONNECT GROUND CABLE

a.
C335926

Connect the ground cable with the bolt.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 41110F 9.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 33119 11.INSTALL STIFFENER PLATE LH

a.

Install the stiffener plate LH with the 4 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 33118 12.INSTALL STIFFENER PLATE RH

a.

Install the stiffener plate RH with the 4 bolts.

Torque:
71.5 N*m (729 kgf*cm, 53 ft.*lbf)


Hide 12584 13.INSTALL NO. 4 CYLINDER BLOCK INSULATOR

a.

Install the No. 4 cylinder block insulator.


Hide 28100 14.INSTALL STARTER ASSEMBLY (for 1KD-FTV)

Hide 28100 15.INSTALL STARTER ASSEMBLY (for 1GD-FTV)

Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1KD-FTV)

Hide 17410 17.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for 1GD-FTV)

Hide 51561D 18.INSTALL PROPELLER SHAFT GUARD

a.

Install the front propeller shaft guard with the 2 bolts.

Torque:
36.2 N*m (369 kgf*cm, 27 ft.*lbf)


Hide 51442 20.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51410 21.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 33548F 22.INSTALL NO. 1 FLOOR SHIFT BUSH

a.

Install the No. 1 floor shift bush to the floor shift shift lever assembly.


Hide 33530F 23.INSTALL FLOOR SHIFT SHIFT LEVER ASSEMBLY

a.
C333520C01
1.813,1.719 1.948,1.896 0.135,0.177 10 false -
V100135

MP grease


Apply MP grease to the tip of the floor shift shift lever assembly.


b.
C329000C02
1.958,0.688 2.323,0.333 2.323,0.333 2.479,0.333 true 1.146,0.24 1.354,0.458 0.208,0.219 10 false *a 1.75,2.906 1.938,3.083 0.188,0.177 10 false *b 1.844,4.271 2.021,4.448 0.177,0.177 10 false *c 2.531,0.26 2.771,0.5 0.24,0.24 10 false *1
*1 Shift Lever Cap
*a Press Down
*b Clockwise
*c Lock


Cover the shift lever cap with a cloth.


c.

While pressing down on the shift lever cap, turn it clockwise to install the shift lever assembly.


Hide 58280A 24.INSTALL SHIFT LEVER BOOT ASSEMBLY

a.

Install the shift lever boot assembly with the 6 screws and 4 clips.


Hide 58810J 25.INSTALL CONSOLE BOX ASSEMBLY

Hide 33504F 26.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

a.

Install the shift lever knob sub-assembly to the shift lever.


Hide 28800 27.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION