Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY
RM33K0E _52 Drivetrain _043595 AXLE AND DIFFERENTIAL _0230449 FRONT DIFFERENTIAL CARRIER ASSEMBLY A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 41110F 1.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

a.
C237477

Install the front No. 3 differential support to the front differential carrier assembly with the 2 bolts.

Torque:
107.9 N*m (1100 kgf*cm, 80 ft.*lbf)


b.

Support the front differential with a jack.


c.

Install the front differential carrier assembly.

C327404C01
0.323,0.063 0.635,0.26 0.313,0.198 10 false *a 0.354,2.073 0.667,2.271 0.313,0.198 10 false *b 4.333,0.083 4.646,0.281 0.313,0.198 10 false *a 4.333,1.958 4.646,2.156 0.313,0.198 10 false *b 4.271,4.135 4.583,4.333 0.313,0.198 10 false *a 4.26,6.031 4.573,6.229 0.313,0.198 10 false *b
*a Rear of Vehicle *b Side of Vehicle
V113147

Install in this Direction - -



d.
C323260

Install the differential mount nut.

Torque:
93.5 N*m (953 kgf*cm, 69 ft.*lbf)


e.
C323262C01
2.229,0.417 2.594,0.417 false 1.854,1.875 2.531,1.875 false 2.063,0.333 2.375,0.531 0.313,0.198 10 false *1 1.677,1.792 1.99,1.99 0.313,0.198 10 false *2
*1 Upper Differential Mount Stopper
*2 Lower Differential Mount Stopper


Install the upper differential mount stopper and lower differential mount stopper to the front No. 2 differential support.


f.
C323258N01
0.49,1.208 0.646,1.406 0.156,0.198 10 true A 1.198,1.271 1.354,1.469 0.156,0.198 10 true A 2.958,1.406 3.115,1.604 0.156,0.198 10 true B

Install the front No. 2 mounting support with the 3 bolts and nut.

Torque:
Bolt A : 160 N*m (1632 kgf*cm, 118 ft.*lbf)
Bolt B : 105 N*m (1071 kgf*cm, 77 ft.*lbf)


g.
C323261C01
0.875,0.396 1.323,0.396 false 0.885,1.854 1.438,1.854 false 1.375,0.302 1.688,0.5 0.313,0.198 10 false *1 1.49,1.771 1.802,1.969 0.313,0.198 10 false *2
*1 Upper Differential Mount Stopper
*2 Lower Differential Mount Stopper


Install the upper differential mount stopper and lower differential mount stopper to the front No. 1 differential support.


h.
C323259N01
2.552,0.052 2.698,0.24 0.146,0.188 10 true A 2.719,0.229 2.875,0.427 0.156,0.198 10 true A 3.052,0.208 3.208,0.406 0.156,0.198 10 true A 0.448,1.479 0.604,1.677 0.156,0.198 10 true B

Install the front No. 1 mounting support with the 4 bolts and nut.

Torque:
Bolt A : 186.2 N*m (1899 kgf*cm, 137 ft.*lbf)
Bolt B : 105 N*m (1071 kgf*cm, 77 ft.*lbf)


i.
C323256

Install the bracket with the bolt.

Torque:
18.55 N*m (189 kgf*cm, 14 ft.*lbf)


j.

Connect the differential motor actuator connector.


k.
C323255

Install the bracket with the bolt.

Torque:
18.55 N*m (189 kgf*cm, 14 ft.*lbf)


l.

Connect the oil temperature sensor connector.


m.
C323254

Connect the hose to the front differential union.


n.
C323253

Install the differential breather tube bracket with the bolt.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


o.
C330144

Connect the breather hose to the differential breather tube bracket.


p.

Lower the jack.


Hide 44200 2.INSTALL POWER STEERING LINK ASSEMBLY

a.

Remove the power steering link assembly with the 2 bolts, 2 washers and 2 nuts.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


Hide 45219 3.CONNECT STEERING SLIDING YOKE

Hide 28100 4.INSTALL STARTER ASSEMBLY (for 1GR-FE)

Hide 17105 5.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH (for 1GR-FE)

Hide 31470 6.INSTALL CLUTCH RELEASE CYLINDER ASSEMBLY (for Manual Transmission)

a.
C323257

Install the bracket with the bolt.

Torque:
68 N*m (693 kgf*cm, 50 ft.*lbf)


b.

Install the clutch release cylinder with the 2 bolts.

Torque:
11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 43420 7.INSTALL FRONT DRIVE SHAFT ASSEMBLY LH

Hide 43410 8.INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51442 11.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51441 12.INSTALL NO. 1 ENGINE UNDER COVER