Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0213897 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101Q 1.INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY (w/ Television Antenna)

a.
E333168

Attach the clamps to install the No. 4 antenna cord sub-assembly.


b.

Connect the connectors.


c.

Attach the guide and install the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 86101D 2.INSTALL NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.
E318986

Attach the clamps and guide to install the No. 3 antenna cord sub-assembly.


b.

Install the bolt and connect the connector.

Torque:
8.7 N*m (89 kgf*cm, 77 in.*lbf)


Hide 86101J 3.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

Align the positioning tape of the No. 2 antenna cord sub-assembly with the protrusions of the roof headlining and wrap the positioning tape around them to install the positioning tape as shown in the illustration.

E320230C01
0.865,1.24 0.76,0.698 true 6.125,0.531 5.677,0.5 true 3.813,1.365 3.969,1.563 0.156,0.198 10 false A 4.094,6.448 4.25,6.646 0.156,0.198 10 false A 0.708,0.531 1.021,0.729 0.313,0.198 10 false *a 5.521,0.427 5.833,0.625 0.313,0.198 10 false *a
*a Positioning Tape - -
V100155

Tape - -



b.

Install the No. 2 antenna cord sub-assembly with the tape aligned to each marking of the roof headlining assembly as shown in the illustration.

HINT:
·

Secure the surplus of the No. 2 antenna cord sub-assembly at the <A> area of the illustration.


·

Secure the front part of the No. 2 antenna cord sub-assembly aligning the edge of the positioning tape and tab section of the roof headlining assembly.


·

Secure the rear part of the No. 2 antenna cord sub-assembly aligning the edge of the positioning tape and tab section of the roof headlining assembly.




Hide 63310 4.INSTALL ROOF HEADLINING ASSEMBLY

Hide 86101 5.INSTALL ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

Install the antenna cord sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

E318983


b.

Attach the clamps shown in the illustration.


c.

Connect the connector.


Hide 86101 6.INSTALL ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

w/o Navigation System:

i.

Install the antenna cord sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

E333163


ii.

Attach the clamps shown in the illustration.


iii.

Connect the connector.



b.

w/ Navigation System:

i.

Install the antenna cord sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

E333166


ii.

Attach the clamps shown in the illustration.


iii.

Connect the connector.



c.

w/ Television Antenna:

i.

Install the antenna cord sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

E333164


ii.

Attach the clamps shown in the illustration.


iii.

Connect the connector.



d.

w/ Television Antenna, w/ Telematics Transceiver

i.

Install the antenna cord sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)

E333165


ii.

Attach the clamps shown in the illustration.


iii.

Connect the connector.



Hide 55302A 7.INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).