Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
66425A
1.INSTALL REAR NO. 2 SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the claw to install the rear No. 2 side rail spacer LH.
66415A
2.INSTALL REAR NO. 2 SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Attach the claw to install the rear No. 2 side rail spacer RH.
66424
3.INSTALL REAR SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the claw to install the rear side rail spacer LH.
66414A
4.INSTALL REAR SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Attach the claw to install the rear side rail spacer RH.
66423
5.INSTALL FRONT SIDE RAIL SPACER LH (w/o Curtain Shield Airbag)
Attach the claw to install the front side rail spacer LH.
66413B
6.INSTALL FRONT SIDE RAIL SPACER RH (w/o Curtain Shield Airbag)
Attach the claw to install the front side rail spacer RH.
63310
7.INSTALL ROOF HEADLINING ASSEMBLY
|
Movement Direction |
Insert the roof headlining assembly into the cabin from the back door.
Check that the corners of the roof headlining assembly are not folded, twisted or otherwise deformed and that none of the mounted parts have fallen off.
Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.
Do not damage the roof headlining assembly or vehicle interior.
Install the visor holder as shown in the illustration.
|
Install in this Direction |
Attach the claw to install the visor holder as shown in the illustration.
Use the same procedure for both visor holders.
Install the roof headlining assembly with the 2 clips.
Connect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH | *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH | *2 | Rear Door Opening Trim Weatherstrip RH |
Connect the connector to the rear pillar RH.
Connect the connector and attach the clamp to the front pillar RH.
Connect the connector and attach the clamp to the front pillar LH.
74620B
8.INSTALL REAR ASSIST GRIP ASSEMBLY
Use the same procedure for both rear assist grip assemblies.
Install the 2 clips and 2 assist grip covers to the rear assist grip.
Temporarily install the assist grip covers.
|
Install in this Direction |
Attach the clip.
Push in the assist grip covers to install the rear assist grip assembly.
74610A
9.INSTALL ASSIST GRIP SUB-ASSEMBLY
Use the same procedure for all assist grip sub-assemblies.
Install the 2 clips and 2 assist grip covers to the assist grip.
Temporarily install the assist grip covers.
|
Install in this Direction |
Attach the clip.
Push in the assist grip covers to install the assist grip sub-assembly.
74320
10.INSTALL VISOR ASSEMBLY LH
Install the visor assembly LH with the 2 screws.
When installing the visor assembly LH, make sure that the arrow on the back side of the visor bracket faces the front of the vehicle.
Connect the visor assembly LH to the visor holder.
74310
11.INSTALL VISOR ASSEMBLY RH
Install the visor assembly RH with the 2 screws.
When installing the visor assembly RH, make sure that the arrow on the back side of the visor bracket faces the front of the vehicle.
Connect the visor assembly RH to the visor holder.
74325
12.INSTALL VISOR BRACKET COVER LH
|
Install in this Direction |
Attach the claw to install the visor bracket cover LH as shown in the illustration.
74325
13.INSTALL VISOR BRACKET COVER RH
|
Install in this Direction |
Attach the claw to install the visor bracket cover RH as shown in the illustration.
73139C
14.INSTALL REAR SEAT BELT COVER
|
Install in this Direction |
Attach the guide.
Attach the clip and claw to install the rear seat belt cover as shown in the illustration.
81240
15.INSTALL NO. 1 ROOM LIGHT ASSEMBLY
81360T
16.INSTALL SPOT LIGHT ASSEMBLY
81260A
17.INSTALL MAP LIGHT ASSEMBLY
for LED Type:
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT(for LED Type)>INSTALLATION
for Bulb Type:
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT(for Bulb Type)>INSTALLATION
62472D
18.INSTALL UPPER REAR PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip to install the upper rear pillar garnish LH as shown in the illustration.
Install the rear seat hook with the bolt.
Connect the rear No. 2 seat outer belt assembly LH with the bolt.
62471D
19.INSTALL UPPER REAR PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip to install the upper rear pillar garnish RH as shown in the illustration.
Install the rear seat hook with the bolt.
Connect the rear No. 2 seat outer belt assembly RH with the bolt.
73178B
20.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62639A
21.INSTALL QUARTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip to install the quarter pillar garnish LH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip LH |
Connect the rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the rear No. 1 seat outer belt assembly LH with the bolt.
62638A
22.INSTALL QUARTER PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip to install the quarter pillar garnish RH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip RH |
Connect the rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the rear No. 1 seat outer belt assembly RH with the bolt.
73178B
23.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62512
24.INSTALL QUARTER INSIDE TRIM BOARD LH
|
Install in this Direction |
Attach the clip and claw to install the quarter inside trim board LH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip LH |
Connect the rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the rear No. 2 seat outer belt assembly LH with the bolt.
Connect the rear No. 1 seat outer belt assembly LH with the bolt.
62511
25.INSTALL QUARTER INSIDE TRIM BOARD RH
Connect the connector.
|
Install in this Direction |
Attach the clip and claw to install the quarter inside trim board RH as shown in the illustration.
| *1 | Rear Door Opening Trim Weatherstrip RH |
Connect the rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the rear No. 2 seat outer belt assembly RH with the bolt.
Connect the rear No. 1 seat outer belt assembly RH with the bolt.
73233B
26.INSTALL REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER
Use the same procedure for both rear No. 2 seat outer lap belt anchor covers.
|
Install in this Direction |
Attach the claw to install the rear No. 2 seat outer lap belt anchor cover as shown in the illustration.
73233A
27.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
Use the same procedure for both rear No. 1 seat outer lap belt anchor covers.
|
Install in this Direction |
Attach the claw to install the rear No. 1 seat outer lap belt anchor cover as shown in the illustration.
67935
28.INSTALL BACK DOOR SCUFF PLATE
Attach the clip and claw to install the back door scuff plate as shown in the illustration.
|
Install in this Direction | - | - |
62412B
29.INSTALL UPPER CENTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip to install the upper center pillar garnish LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the front seat outer belt assembly LH with the bolt.
62411B
30.INSTALL UPPER CENTER PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip to install the upper center pillar garnish RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
| *2 | Rear Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the front seat outer belt assembly RH with the bolt.
73178A
31.INSTALL SEAT BELT ANCHOR COVER CAP
Use the same procedure for both seat belt anchor cover caps.
|
Install in this Direction |
Attach the claw to install the seat belt anchor cover cap as shown in the illustration.
62414A
32.INSTALL LOWER CENTER PILLAR GARNISH LH
|
Install in this Direction |
Attach the clip and claw to install the lower center pillar garnish LH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip LH |
| *2 | Rear Door Opening Trim Weatherstrip LH |
Connect the front door opening trim weatherstrip LH and rear door opening trim weatherstrip LH in the range shown in the illustration.
Connect the front seat outer belt assembly LH with the bolt.
62413A
33.INSTALL LOWER CENTER PILLAR GARNISH RH
|
Install in this Direction |
Attach the clip and claw to install the lower center pillar garnish RH as shown in the illustration.
| *1 | Front Door Opening Trim Weatherstrip RH |
| *2 | Rear Door Opening Trim Weatherstrip RH |
Connect the front door opening trim weatherstrip RH and rear door opening trim weatherstrip RH in the range shown in the illustration.
Connect the front seat outer belt assembly RH with the bolt.
73233
34.INSTALL LAP BELT OUTER ANCHOR COVER
Use the same procedure for both outer lap belt anchor covers.
|
Install in this Direction |
Attach the claw to install the outer lap belt anchor cover as shown in the illustration.
67918E
35.INSTALL REAR DOOR SCUFF PLATE LH
|
Install in this Direction |
Attach the claw to install the rear door scuff plate LH as shown in the illustration.
Attach claw A shown in the illustration first.
67917C
36.INSTALL REAR DOOR SCUFF PLATE RH
|
Install in this Direction |
Attach the claw to install the rear door scuff plate RH as shown in the illustration.
Attach claw A shown in the illustration first.
67914B
37.INSTALL FRONT DOOR SCUFF PLATE LH
|
Install in this Direction |
Attach the claw to install the front door scuff plate LH as shown in the illustration.
Attach claw A shown in the illustration first.
67913B
38.INSTALL FRONT DOOR SCUFF PLATE RH
|
Install in this Direction |
Attach the claw to install the front door scuff plate RH as shown in the illustration.
Attach claw A shown in the illustration first.
62212
39.INSTALL FRONT PILLAR GARNISH LH
62211
40.INSTALL FRONT PILLAR GARNISH RH
74603
41.INSTALL FRONT ASSIST GRIP SUB-ASSEMBLY
42.INSTALL REAR NO. 2 SEAT ASSEMBLY LH
43.INSTALL REAR NO. 2 SEAT ASSEMBLY RH
44.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
45.CHECK SRS WARNING LIGHT