Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD
RM33K0E _56 Audio / Visual / Telematics _043541 AUDIO / VIDEO _0213897 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the radio antenna cord removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power back door system (Click here)

CAUTION:
B403904

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(for Type B)>PRECAUTION


PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ighition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55302A 3.REMOVE UPPER INSTRUMENT PANEL SUB-ASSEMBLY

Hide 86101 4.REMOVE ANTENNA CORD SUB-ASSEMBLY (for RHD)

a.

Disconnect the connector.

E318983


b.

Detach the clamps shown in the illustration.


c.

Remove the bolt and antenna cord sub-assembly.


Hide 86101 5.REMOVE ANTENNA CORD SUB-ASSEMBLY (for LHD)

a.

w/o Navigation System:

i.

Disconnect the connector.

E333163


ii.

Detach the clamps shown in the illustration.


iii.

Remove the bolt and antenna cord sub-assembly.



b.

w/ Navigation System:

i.

Disconnect the connector.

E333166


ii.

Detach the clamps shown in the illustration.


iii.

Remove the bolt and antenna cord sub-assembly.



c.

w/ Television Antenna:

i.

Disconnect the connectors.

E333164


ii.

Detach the clamps shown in the illustration.


iii.

Remove the bolt and antenna cord sub-assembly.



d.

w/ Television Antenna, w/ Telematics Transceiver

i.

Disconnect the connectors.

E333165


ii.

Detach the clamps shown in the illustration.


iii.

Remove the bolt and antenna cord sub-assembly.



Hide 63310 6.REMOVE ROOF HEADLINING ASSEMBLY

Hide 86101J 7.REMOVE NO. 2 ANTENNA CORD SUB-ASSEMBLY

a.

Remove the tape enough that the No. 2 antenna cord sub-assembly can be removed, and then remove the No. 2 antenna cord sub-assembly from the roof headlining.

E318985C01
0,0 0,0 false
V100155

Tape - -



Hide 86101D 8.REMOVE NO. 3 ANTENNA CORD SUB-ASSEMBLY

a.
E318986

Disconnect the connector and remove the bolt.


b.

Detach the clamps, guide and remove the No. 3 antenna cord sub-assembly.


Hide 86101Q 9.REMOVE NO. 4 ANTENNA CORD SUB-ASSEMBLY (for Television Antenna)

a.
E333168

Disconnect the connectors and remove the bolt.


b.

Detach the clamps, guide and remove the No. 4 antenna cord sub-assembly.