Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR
RM33K0E _58 Vehicle Interior _043552 SUPPLEMENTAL RESTRAINT SYSTEMS _0219483 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89860A 1.INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
·
B394718

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·
B392779

If this procedure is performed without disconnecting the negative (-) terminal of the battery, the airbag may deploy even if an impact is applied only to the side airbag sensor assembly LH. Therefore, make sure that the negative (-) terminal of the battery is disconnected before performing this procedure.




c.

Attach the guide and hold the side airbag sensor assembly LH in place.


d.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side airbag sensor assembly LH has been dropped, replace it with a new one.

·

When installing the side airbag sensor assembly LH, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Tighten the bolt while holding the side airbag sensor assembly LH because the side airbag sensor assembly LH guide is easily damaged.




e.

Before connecting the airbag connector, check that the position of the housing lock is correct as shown in the illustration.

B319865C14
2.719,1.406 3.26,1.406 false 5.958,1.417 6.5,1.417 false 0.531,1.771 0.802,1.771 false 3.333,1.323 3.646,1.479 0.313,0.156 10 false *c 6.552,1.333 6.865,1.49 0.313,0.156 10 false *c 1.75,1.042 2.135,1.24 0.385,0.198 10 true *a 5,1.021 5.292,1.188 0.292,0.167 10 true *b 0.354,1.698 0.667,1.854 0.313,0.156 10 false *d 0.042,0.052 5.885,0.583 5.844,0.531 6 true . 1.313,0.49 7.094,0.76 5.781,0.271 6 true . 1.323,0.604 2.656,0.99 1.333,0.385 6 true . 4.615,0.552 5.948,0.938 1.333,0.385 6 true .
*a Correct *b Incorrect
*c CPA *d Housing



f.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

While holding the CPA, be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when connecting the airbag connector.


B403898C01
1.594,1.958 1.594,1.208 false 3.469,1.167 3.125,0.583 true 5.448,0.906 5.76,1.063 0.313,0.156 10 false *c 1.542,2.01 1.854,2.167 0.313,0.156 10 false *a 2.938,0.479 3.25,0.635 0.313,0.156 10 false *b
*a CPA *b CPA Upper Part
*c Connection is Completed - -
V113147

Connect in this Direction - -




g.

Check that there is no looseness in the installation parts of the side airbag sensor assembly LH.


Hide 62512 2.INSTALL QUARTER INSIDE TRIM BOARD LH

Hide 73233B 3.INSTALL REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER

Hide 73233A 4.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER

Hide 67935 5.INSTALL BACK DOOR SCUFF PLATE

Hide 67918E 6.INSTALL REAR DOOR SCUFF PLATE LH

Hide 7.INSTALL REAR NO. 2 SEAT ASSEMBLY LH

Hide 8.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION