When the engine is cranked, an STA signal is sent to the ECM from certification ECU (smart key ECU assembly). When the STA and NE signals are received by the ECM, Tr1 inside the ECM turns on and current flows through the coil of the C/OPN NO.1 relay. As a result, the relay switches on and the fuel pump operates with power from the FUEL PMP/AIR PMP HTR relay. While the NE signal is being sent (while the engine is running), the fuel pump continues to operate since Tr1 in the ECM continues to stay on (the C/OPN NO.1 relay is on). The speed of the fuel pump is regulated at two speeds (high and low) according to the state of the engine (cranking, light load or heavy load). When Tr2 inside the ECM is off, the fuel pump operates at high speed. When Tr2 turns on during idling or light loads, current flows to the fuel pump through the fuel pump resistor and the fuel pump operates at low speed.
Refer to DTC P0230.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>P0230
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
| Tester Display |
|---|
| Control the Fuel Pump / Speed |
Check the relay operation while operating it using the GTS.
Operating noise can be heard from the relay.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the relay (FUEL PMP/AIR PMP HTR).
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Engine Room Relay Block Assembly |
| *2 | FUEL PMP/AIR PMP HTR |
Remove the FUEL PMP/AIR PMP HTR relay from the engine room relay block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FUEL PMP/AIR PMP HTR relay terminal 2 - Body ground | Cranking | 11 to 14 V |
| FUEL PMP/AIR PMP HTR relay terminal 3 - Body ground | Cranking | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect fuel pump resistor.
Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL PUMP RESISTOR>INSPECTION
| Result | Proceed to |
|---|---|
| OK | A |
| NG | B |
A
B
Inspect the fuel pump.
Click hereEngine / Hybrid System>1GR-FE FUEL>FUEL PUMP>INSPECTION
Perform "Inspection After Repair" after replacing the fuel pump.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the FUEL PMP/AIR PMP HTR relay from the engine room relay block assembly.
Disconnect the fuel pump resistor connector.
Disconnect the fuel pump connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| FUEL PMP/AIR PMP HTR relay terminal 5 - A76-1 | Always | Below 1 Ω |
| A76-2 - O6-4 | Always | Below 1 Ω |
| FUEL PMP/AIR PMP HTR relay terminal 4 - O6-4 | Always | Below 1 Ω |
| O6-5 - Body ground | Always | Below 1 Ω |
| FUEL PMP/AIR PMP HTR relay terminal 1 - G158-4 (FPR) | Always | Below 1 Ω |
| FUEL PMP/AIR PMP HTR relay terminal 5 or A76-1 - Body ground | Always | 10 kΩ or higher |
| A76-2 or O6-4 - Body ground | Always | 10 kΩ or higher |
| FUEL PMP/AIR PMP HTR relay terminal 4 or O6-4 - Body ground | Always | 10 kΩ or higher |
| FUEL PMP/AIR PMP HTR relay terminal 1 or G158-4 (FPR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click here
Inspect the ECM power source circuit.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>ECM Power Source Circuit
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the relay (C/OPN NO.1).
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>RELAY>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the instrument panel junction block connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2P-8 - G158-5 (FC) | Always | Below 1 Ω |
| 2P-8 or G158-5 (FC) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG