If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
When the transmitter battery of the electrical key transmitter sub-assembly is depleted, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
When the smart key cancel function has been canceled on the customization menu, the brake pedal is depressed and the electrical key transmitter sub-assembly is held near the engine switch.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Power Supply Condition ·
IG Relay Monitor(Inside) ·
IG Relay Monitor(Outside) ·
Latch Circuit ·
ACC Relay Monitor |
- |
Refer to "SYSTEM DIAGRAM".
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select the Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.
If the smart entry and start system is disabled through the customize function, enable the system before performing troubleshooting.
Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to the smart entry and start system (for Entry Function) precaution.
Inspect the fuses of circuits related to this system before performing the following procedure.
After completing repairs, confirm that the problem does not occur.
The indoor electrical key antenna assemblies have an antenna coil between each two CLG terminals.
The door control receiver is also related to interior verification.
When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
If the room oscillator does not recognize, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).
If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether the malfunction was caused by wave interference.
| Tester Display |
|---|
| Operation History |
| Parameter Name | Content |
|---|---|
| Operating Engine Switch / Key RF Signal Interference | When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
| Parameter Name | Content |
|---|---|
| Operating Power Switch/ Indoor oscillator LF Signal Interference | When the engine switch was operated, the room oscillator could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).
If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high. |
Check the transmitter battery level of the electrical key transmitter sub-assembly that was checked first.
Press and hold the lock switch of the transmitter for 5 seconds and check the number of times that the transmitter LED illuminates.
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is being used. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
Even if the transmitter battery is depleted, it is still possible to start the engine by holding the electrical key transmitter sub-assembly near the engine switch, depressing the brake pedal and pressing the engine switch.
| Result | Proceed to |
|---|---|
| Transmitter LED illuminates 3 times or more when switch is pressed and held | A |
| Transmitter LED does not illuminate when switch is pressed and held | B |
| Transmitter LED illuminates once or twice but not a third time | C |
A
B
C
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Key Low Battery | Transmitter battery depleted | Yes or No | Yes: Transmitter battery depleted
No: Transmitter battery not depleted |
The electrical key transmitter sub-assembly sends voltage information to the certification ECU (smart key ECU assembly) when it is transmitting. The certification ECU (smart key ECU assembly) displays "Yes" for the "Key Low Battery" item of the Data List when this voltage information indicates 2.2 V or less.
This Data List item should be checked when the electrical key transmitter sub-assembly is at room temperature (example: at -20°C (-4°F), "Yes" may be displayed even if the transmitter battery is new). |
| Tester Display |
|---|
| Key Low Battery |
"No" is displayed in the Data List.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Clear the DTCs.
Recheck for DTCs.
DTC is not output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Get into the vehicle while carrying a different, previously-registered electrical key transmitter sub-assembly.
for Automatic Transmission
Move the shift lever to P.
With the brake pedal*1 or clutch pedal*2 released, check that pressing the engine switch causes the power source mode to change.
*1: for Automatic Transmission
*2: for Manual Transmission
| Result | Proceed to |
|---|---|
| Power source mode does not change | A |
| Off → on (ACC) → on (IG) → off | B |
A
B
Check that the wireless door lock functions operate normally.
Check that the entry lock and unlock functions operate on each door.
If the door control receiver is defective, code verification does not begin in the cabin and the entry lock and unlock functions do not operate.
Wireless door lock, entry door lock and entry door unlock functions operate normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the transmitter battery from the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
| *1 | Engine Switch |
| *2 | Electrical Key Transmitter Sub-assembly |
With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly near the engine switch and check if the power source mode changes.
*1: for Automatic Transmission
*2: for Manual Transmission
If the power source mode changes, the cabin verification is malfunctioning.
The power source mode changes.
| Result | Proceed to |
|---|---|
| The power source mode changes | A |
| The power source mode does not change | B |
A
B
Install the transmitter battery to the electrical key transmitter sub-assembly.
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Bring the electrical key transmitter sub-assembly near the No. 1 indoor electrical key antenna assembly (front floor) and perform a smart entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 1 indoor electrical key antenna assembly (front floor).
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (rear floor) and perform a smart entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (rear floor).
Bring the electrical key transmitter sub-assembly near the No. 2 indoor electrical key antenna assembly (inside luggage) and perform a smart entry and start system check.
Communication may not be possible if the electrical key transmitter sub-assembly is within 0.2 m (0.656 ft.) of the No. 2 indoor electrical key antenna assembly (inside luggage).
As the effect of wave interference decreases by moving the electrical key transmitter sub-assembly close to each indoor electrical key antenna assembly, it may be possible to check whether wave interference is the cause of the problem.
If the problem only occurs in specific places or at specific times, wave interference may be the cause of the problem. Also, parts installed by the dealer may cause wave interference. As a result, when parts have been installed by the dealer, it may be necessary to remove those parts before inspecting the vehicle.
There may be wave interference if the vehicle is near broadcasting antennas, large video displays, wireless garage door opener systems, wireless security cameras, home security systems, etc. In this case, move the vehicle to a different location and check if there is any improvement.
If a tool for checking electric waves, such as a signal strength meter, is available, move around the area while observing both the LF band (used by the vehicle antenna to form the detection area) and RF band (used by the electrical key transmitter sub-assembly for transmission) to check for locations where there is wave interference.
| Result | Proceed to |
|---|---|
| System cannot be operated | A |
| System can be operated | B |
A
B
Check the following antennas in key diagnostic mode.
Select either channel 1 or channel 2 and perform the key diagnostic mode inspection for each channel.
| Tester Display |
|---|
| Communication Check(Key Diag Mode) |
If the buzzer sounds with [CH1] displayed but not with [CH2], the electrical key transmitter sub-assembly cannot be detected by channel 2 due to a malfunction, such as wave interference.
| *a | Inspection Point |
Check the No. 1 indoor electrical key antenna assembly (front floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (rear floor).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
| *a | Inspection Point |
Check the No. 2 indoor electrical key antenna assembly (inside luggage).
When the electrical key transmitter sub-assembly is at either inspection point, check that the wireless door lock buzzer sounds.
If the buzzer sounds, it can be determined that the vehicle interior transmitters are operating normally.
It is possible to check which indoor electrical key antenna assembly (front floor, rear floor or inside luggage) is operating by the sounding of the buzzer.
If the buzzer does not sound for any indoor electrical key antenna assemblies, the certification ECU (smart key ECU assembly) circuit may be malfunctioning.
| Result | Proceed to |
|---|---|
| Front floor operation check fails | A |
| Rear floor operation check fails | B |
| Inside luggage operation check fails | C |
| The wireless buzzer sounds/does not sound for all indoor electrical key antenna assemblies | D |
A
B
C
D
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the G28 No. 1 indoor electrical key antenna assembly (front floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-31 (CLG1) - G28-1 (ANTE1) | Always | Below 1 Ω |
| G17-30 (CG1B) - G28-3 (CLGB) | Always | Below 1 Ω |
| G17-31 (CLG1) or G28-1 (ANTE1) - Body ground | Always | 10 kΩ or higher |
| G17-30 (CG1B) or G28-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G17 certification ECU (smart key ECU assembly) connector.
Connect the G28 No. 1 indoor electrical key antenna assembly (front floor) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 1 Indoor Electrical Key Antenna Assembly (Front Floor)) |
*b | Waveform 1 |
| *c | Door open | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| G28-1 (ANTE1) - G28-3 (CLGB) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the transmitter battery.
Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL TRANSMITTER(w/ Smart Entry and Start System)>INSPECTION
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the transmitter battery will not be able to be installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Smart Entry and Start System)>REPLACEMENT
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the N9 No. 2 indoor electrical key antenna assembly (rear floor) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-6 (CLG2) - N9-1 (ANTE2) | Always | Below 1 Ω |
| G17-23 (CG2B) - N9-3 (CLGB) | Always | Below 1 Ω |
| G17-6 (CLG2) or N9-1 (ANTE2) - Body ground | Always | 10 kΩ or higher |
| G17-23 (CG2B) or N9-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G17 certification ECU (smart key ECU assembly) connector.
Connect the N9 No. 2 indoor electrical key antenna assembly (rear floor) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 2 Indoor Electrical Key Antenna Assembly (Rear Floor)) |
*b | Waveform 1 |
| *c | Door open | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| N9-1 (ANTE2) - N9-3 (CLGB) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the N39 No. 2 indoor electrical key antenna assembly (inside luggage) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-28 (CLG7) - N39-1 (ANTE7) | Always | Below 1 Ω |
| G17-29 (CG7B) - N39-3 (CLGB) | Always | Below 1 Ω |
| G17-28 (CLG7) or N39-1 (ANTE7) - Body ground | Always | 10 kΩ or higher |
| G17-29 (CG7B) or N39-3 (CLGB) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the G17 certification ECU (smart key ECU assembly) connector.
Connect the N39 No. 2 indoor electrical key antenna assembly (inside luggage) connector.
Using an oscilloscope, check the waveform.
| *a | Component with harness connected
(No. 2 Indoor Electrical Key Antenna Assembly (Inside Luggage)) |
*b | Waveform 1 |
| *c | Door open | *d | After approximately 30 seconds from when the door is closed |
| Tester Connection | Condition | Tool Setting | Specified Condition |
|---|---|---|---|
| N39-1 (ANTE7) - N39-3 (CLGB) | Procedure:
1.
All doors closed 2.
Engine switch off 3.
Electrical key transmitter sub-assembly not inside vehicle 4.
Door is open 5.
Door is closed 6.
Within 30 seconds |
2 V/DIV., 500 ms./DIV. | Pulse generation
(See waveform 1) |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Connect the G16 and G17 certification ECU (smart key ECU assembly) connectors.
Press the engine switch and check that the engine starts.
Engine starts.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Automatic Transmission
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Stop Light Switch1 | State of brake pedal | ON or OFF | ON: Brake pedal depressed
OFF: Brake pedal released |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
| Tester Display |
|---|
| Stop Light Switch1 |
The item in the Data List changes when the brake pedal is depressed and released.
for Manual Transmission
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Neutral SW/ Clutch SW | State of clutch pedal | ON or OFF | ON: Clutch pedal depressed
OFF: Clutch pedal released |
·
Use this item to help determine if the clutch start switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
| Tester Display |
|---|
| Neutral SW/ Clutch SW |
The item in the Data List changes when the clutch pedal is depressed and released.
| Proceed to |
|---|
| OK |
| NG (for Automatic Transmission) |
| NG (for Manual Transmission) |
OK
NG (for Automatic Transmission)
NG (for Manual Transmission)
Connect the G16 certification ECU (smart key ECU assembly) connector.
Connect the 2E and 2J instrument panel junction block assembly connectors.
Read the Data List according to the display on the GTS.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Supply Condition | Power supply state | ST ON, All OFF, IG ON or ACC ON | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC) IG ON: Engine switch on (IG) ST ON: Sending engine start request signal |
- |
| Tester Display |
|---|
| Power Supply Condition |
Measure the voltage while checking the Data List on the GTS.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G16-20 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| G16-21 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (IG) | 8.5 V or higher | |
| Engine switch on (ACC) | 8.5 V or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG1 NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Remove the IG1 NO. 1 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-20 (IG1D) - IG1 NO. 1 relay terminal 1 | Always | Below 1 Ω |
| IG1 NO. 1 relay terminal 2 - Body ground | Always | Below 1 Ω |
| G16-20 (IG1D) or IG1 NO. 1 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Battery voltage not applied to terminals 1 and 2 | 10 kΩ or higher |
| Battery voltage applied to terminals 1 and 2 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Remove the IG2 relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-20 (IG1D) - IG2 relay terminal 1 | Always | Below 1 Ω |
| IG2 relay terminal 2 - Body ground | Always | Below 1 Ω |
| G16-20 (IG1D) or IG2 relay terminal 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Remove the body ECU from the instrument panel junction block assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Measure the resistance according to the value(s) in the table below.
| *A | for RHD | *B | for LHD |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2A-1 - 2P-5 | Battery voltage not applied to terminals 2E-2 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2E-2 and 2J-5 | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2R-1 - 2P-5 | Battery voltage not applied to terminals 2E-2 and 2J-5 | 10 kΩ or higher |
| Battery voltage applied to terminals 2E-2 and 2J-5 | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU(for RHD)>REMOVAL
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Disconnect the 2E and 2J instrument panel junction block assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-21 (ACCD) - 2E-2 | Always | Below 1 Ω |
| 2J-5 - Body ground | Always | Below 1 Ω |
| G16-21 (ACCD) or 2E-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Start Switch1 | Engine switch 1 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the engine switch input signal is malfunctioning. |
| Start Switch2 | Engine switch 2 status | ON or OFF | ON: Engine switch pressed
OFF: Engine switch not pressed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
| Tester Display |
|---|
| Start Switch1 |
| Start Switch2 |
ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the engine switch.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH>REMOVAL
for 2TR-FE (for LHD): Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 2TR-FE (for RHD): Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
for 1KD-FTV (for LHD): Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 1KD-FTV (for RHD): Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for RHD)>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>REMOVAL
Inspect the engine switch.
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH>INSPECTION
for 2TR-FE (for LHD): Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for LHD)>INSPECTION
for 2TR-FE (for RHD): Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for RHD)>INSPECTION
for 1KD-FTV (for LHD): Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for LHD)>INSPECTION
for 1KD-FTV (for RHD): Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for RHD)>INSPECTION
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE STARTING>ENGINE SWITCH>REMOVAL
for 2TR-FE (for LHD): Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 2TR-FE (for RHD): Click hereEngine / Hybrid System>2TR-FE STARTING>ENGINE SWITCH(for RHD)>REMOVAL
for 1KD-FTV (for LHD): Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for LHD)>REMOVAL
for 1KD-FTV (for RHD): Click hereEngine / Hybrid System>1KD-FTV STARTING>ENGINE SWITCH(for RHD)>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV STARTING>ENGINE SWITCH>REMOVAL
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Disconnect the G45 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-18 (SSW1) - G45-5 (SS1) | Always | Below 1 Ω |
| G16-16 (SSW2) - G45-1 (SS2) | Always | Below 1 Ω |
| G16-24 (AGND) - G45-6 (AGND) | Always | Below 1 Ω |
| G16-18 (SSW1) or G45-5 (SS1) - Body ground | Always | 10 kΩ or higher |
| G16-16 (SSW2) or G45-1 (SS2) - Body ground | Always | 10 kΩ or higher |
| G16-24 (AGND) or G45-6 (AGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G159*1, G57*2, G129*3 or G50*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Disconnect the A4 skid control ECU (brake actuator assembly) connector.
Disconnect the G16 certification ECU (smart key ECU assembly) connector.
Disconnect the A64 stop light switch assembly connector.
Disconnect the I4 shift lock control ECU (transmission floor shift assembly) connector.
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A64-7 (B) - Body ground | Always | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G16-11 (STP1) - A64-3 (L) | Always | Below 1 Ω |
| G16-11 (STP1) or A64-3 (L) - Body ground | Always | 10 kΩ or higher |
| A64-2 (GND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the stop light switch assembly.
Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the clutch start switch assembly.
Inspect the clutch start switch assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G17 certification ECU (smart key ECU assembly) connector.
Disconnect the B2 clutch start switch assembly connector.
Disconnect the G120*1, C15*2, G130*3 or G49*4 ECM connector.
*1: for 1GR-FE
*2: for 2TR-FE
*3: for 1KD-FTV
*4: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G17-16 (STAR) - B2-2 | Always | Below 1 Ω |
| G17-16 (STAR) or B2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG