To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
28800
3.INSPECT BATTERY
16361A
4.INSPECT FAN AND GENERATOR V BELT
16620
5.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
17801
6.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner filter element sub-assembly from the air cleaner case sub-assembly.
Check that the air cleaner filter element sub-assembly is not excessively dirty.
If the air cleaner filter element sub-assembly is excessively dirty, replace the air cleaner filter element sub-assembly.
If cleaning the air cleaner filter element sub-assembly, blow compressed air to clean it.
Do not start the engine with the air cleaner filter element sub-assembly removed, as this may damage the engine.
When using an air cleaner filter element sub-assembly that uses compressed air, wear safety glasses and a dust mask in order to protect your health.
When an excessive amount of dirt is present, replace the air cleaner filter element sub-assembly.
Reinstall the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.
19100P
7.INSPECT SPARK PLUG
8.INSPECT IGNITION TIMING
Warm up the engine and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Switch off all the accessories and the A/C before connecting the GTS.
Start the engine and idle it.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Active Test / Connect the TC and TE1.
| Active Test Display |
|---|
| Connect the TC and TE1 |
| Data List Display |
|---|
| IGN Advance |
Inspect the ignition timing during idling.
8 to 12° BTDC @ idle
When checking the ignition timing, the transmission should be in N or P.
Refer to the GTS operator's manual for further details.
Cancel the Active Test.
Enter the following menus: Powertrain / Engine / Data List / IGN Advance.
| Tester Display |
|---|
| IGN Advance |
Inspect the ignition timing during idling.
7 to 24° BTDC @ idle
When checking the ignition timing, the transmission should be in N or P.
Check that the ignition timing advances immediately when the engine speed is increased.
When not using the GTS:
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Do not improperly connect the terminals. This may damage the engine.
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
Use a timing light that detects primary signals.
After checking, be sure to wrap the wire harness with tape.
Start the engine.
Inspect the ignition timing during idling.
8 to 12° BTDC @ idle
Turn all the electrical systems and the A/C off.
When checking the ignition timing, the transmission should be in N or P.
Remove SST from the DLC3.
Inspect the ignition timing during idling.
7 to 24° BTDC @ idle
Disconnect the timing light from the wire of the ignition coil connector for the No. 1 cylinder.
9.INSPECT ENGINE IDLE SPEED
Warm up the engine.
When using the GTS:
Connect the GTS to the DLC3.
Switch off all accessories and the A/C before connecting the GTS.
Start the engine and idle it.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Inspect the engine idle speed.
650 to 750 rpm
When checking the idle speed, the transmission should be in N or P.
Refer to the GTS operator's manual for further details.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
When not using the GTS:
| *a | Front view of DLC3 |
Using SST, connect a tachometer tester probe to terminal 9 (TAC) of the DLC3.
Switch off all accessories and the A/C before connecting the terminals.
Race the engine at 2500 rpm for approximately 90 seconds.
Inspect the engine idle speed.
650 to 750 rpm
When checking the idle speed, the transmission should be in N or P.
Disconnect the tachometer tester probe from the DLC3.
10.INSPECT COMPRESSION
Warm up and stop the engine.
Check for DTCs.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Drain the engine coolant.
Click hereEngine / Hybrid System>1GR-FE COOLING>COOLANT>REPLACEMENT
Remove the intake air surge tank.
Click hereEngine / Hybrid System>1GR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>REMOVAL
Remove the 6 spark plugs.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Disconnect the 6 fuel injector connectors.
Stop fuel injection to prevent damage to the catalyst due to unburned fuel.
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
While cranking the engine, measure the compression pressure.
1300 kPa (13.3 kgf/cm2, 189 psi) or higher
1000 kPa (10.2 kgf/cm2, 145 psi)
100 kPa (1.0 kgf/cm2, 15 psi) or less
Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
Inspect the other cylinders in the same way.
Measure the compression in as short a time as possible.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, and then inspect it again.
If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
If the compression pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.
Connect the 6 fuel injector connectors.
Install the 6 spark plugs.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
Install the intake air surge tank.
Click hereEngine / Hybrid System>1GR-FE INTAKE / EXHAUST>INTAKE MANIFOLD>INSTALLATION
Add engine coolant.
Click hereEngine / Hybrid System>1GR-FE COOLING>COOLANT>REPLACEMENT
Check for DTCs.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
11.INSPECT CO/HC
Start and warm up the engine.
Run the engine at 2500 rpm for approximately 180 seconds, and then idle the engine.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe.
Check the CO/HC concentration at idle.
0 to 0.5%
Refer to applicable local regulation
If the CO/HC concentration is not as specified, perform troubleshooting in the order given below.
Check the air fuel ratio sensor operation.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION
Check the heated oxygen sensor operation.
Click hereEngine / Hybrid System>1GR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION
See the table below for possible causes, and then inspect and repair the applicable causes if necessary.
| CO | HC | Problem | Possible Cause |
|---|---|---|---|
| Normal | High | Rough idling | 1.
Faulty ignition: ·
Incorrect timing ·
Fouled, shorted or improperly gapped plugs 2.
Incorrect valve clearance 3.
Leaky intake and exhaust valves 4.
Leaky cylinders |
| Low | High | Rough idling
(Fluctuating HC reading) |
1.
Vacuum leaks: ·
PCV hoses ·
Intake manifold ·
Throttle body with motor assembly ·
Brake booster line 2.
Lean mixture causing misfire |
| High | High | Rough idling
(Black smoke from exhaust) |
1.
Restricted air cleaner filter element sub-assembly 2.
Plugged PCV valve sub-assembly 3.
Faulty SFI system: ·
Faulty fuel pressure regulator assembly ·
Defective engine coolant temperature sensor ·
Defective intake mass air flow meter sub-assembly ·
Faulty ECM ·
Faulty fuel injector assemblies ·
Faulty throttle body with motor assembly |