Home › Engine / Hybrid System › 1GR-FE ENGINE MECHANICAL › ENGINE UNIT
RM33K0E _51 Engine / Hybrid System _043519 1GR-FE ENGINE MECHANICAL _0225348 ENGINE UNIT A

1GR-FE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.
A346199C01
0.625,0.708 0.813,0.885 0.188,0.177 10 true *a 1.781,0.156 1.948,0.344 0.167,0.188 10 true *b 3.125,2.833 3.313,3.042 0.188,0.208 10 false *c 2.635,2.635 2.875,2.833 0.24,0.198 10 false *d 1.031,2.417 1.26,2.594 0.229,0.177 10 false *e 1.542,2.708 1.75,2.896 0.208,0.188 10 false *f 0.479,1.688 0.698,1.875 0.219,0.188 10 false *a 1.781,1.604 1.99,1.792 0.208,0.188 10 true *b 1.042,3.052 1.281,3.25 0.24,0.198 10 false *d 1.292,1.458 1.49,1.656 0.198,0.198 10 true *a 2.073,2.052 2.281,2.24 0.208,0.188 10 true *b 2.635,3.063 2.875,3.26 0.24,0.198 10 false *d
*a Bolt A
*b Bolt B
*c 19 mm (0.748 in.)
*d 9 mm (0.354 in.)
*e 16 mm (0.630 in.)
*f 27 mm (1.06 in.)


Install the oil pan sub-assembly stud bolt.

i.

Using an E6 "TORX" wrench, install the 4 stud bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)



b.
A346197C01
2.906,1.135 3.156,1.323 0.25,0.188 10 false *a 2.917,2.948 3.125,3.135 0.208,0.188 10 false *b 3.208,2.063 3.406,2.25 0.198,0.188 10 false *c
*a 18 mm (0.709 in.)
*b 12 mm (0.472 in.)
*c 93 mm (3.66 in.)


Install the timing chain cover sub-assembly stud bolt.

i.

Using an E8 "TORX" wrench, install the 2 stud bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.
A346198C01
0.49,1.802 0.729,1.979 0.24,0.177 10 false *a 1.979,2.333 2.188,2.531 0.208,0.198 10 false *b 0.875,2.469 1.052,2.688 0.177,0.219 10 false *c 0.865,3.146 1.063,3.344 0.198,0.198 10 false *d 1.167,2.729 1.375,2.948 0.208,0.219 10 false *e 2.656,2.979 2.854,3.198 0.198,0.219 10 false *f 2.354,2.792 2.552,2.99 0.198,0.198 10 false *d 2.354,3.146 2.552,3.344 0.198,0.198 10 false *d 0.51,0.094 0.74,0.281 0.229,0.188 10 false *a 1.646,1.75 1.823,1.948 0.177,0.198 10 false *b 0.385,0.594 0.615,0.781 0.229,0.188 10 false *a 1.667,1.26 1.854,1.458 0.188,0.198 10 false *b 1.635,0.979 1.813,1.177 0.177,0.198 10 false *b 1.76,0 1.969,0.198 0.208,0.198 10 false *b 0.969,0.865 1.146,1.063 0.177,0.198 10 true *b 2.094,0.448 2.271,0.646 0.177,0.198 10 true *b
*a Bolt A
*b Bolt B
*c 21 mm (0.827 in.)
*d 9 mm (0.354 in.)
*e 34 mm (1.34 in.)
*f 19 mm (0.748 in.)


Install the cylinder head cover sub-assembly stud bolt.

i.

Using an E6 "TORX" wrench, install the 8 stud bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)



Hide 2.INSTALL TAPER SCREW PLUG

a.

Clean the taper screw plug and plug hole.


b.
A270546

Apply adhesive to 2 or 3 threads of the taper screw plug end.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the taper screw plug.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Install the taper screw plug within 3 minutes after applying adhesive.

·

Do not expose the taper screw plug to coolant within 1 hour of the installation.




Hide 13751 3.INSTALL VALVE LIFTER

a.

Apply engine oil to each valve stem and valve lifter, and then install the 24 valve lifters.


b.

Check that the 24 valve lifters rotate smoothly by hand.


Hide 16332 5.INSTALL NO. 1 WATER OUTLET PIPE

a.

for Type A:

Install the No. 1 water outlet pipe with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

for Type B:

Install the No. 1 water outlet pipe with the 2 nuts and bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the knock sensor wire.


Hide 11116 6.INSTALL NO. 2 CYLINDER HEAD GASKET

Hide 11101 9.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13054 10.INSTALL NO. 4 CAMSHAFT SUB-ASSEMBLY

a.

Apply new engine oil to the thrust portion and journals of the No. 4 camshaft sub-assembly.


b.

Install the No. 4 camshaft sub-assembly to the cylinder head LH.


Hide 13053 11.INSTALL NO. 3 CAMSHAFT SUB-ASSEMBLY

a.

Apply new engine oil to the thrust portion and journals of the No. 3 camshaft sub-assembly.


b.

Install the No. 3 camshaft sub-assembly to the cylinder head LH.


Hide 12.INSTALL CAMSHAFT BEARING CAP (for Bank 2)

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.

Temporarily install the crankshaft pulley set bolt.


b.
A326643C03
0.448,1.333 0.615,1.333 0.615,1.333 0.615,0.667 true 0.271,1.25 0.583,1.406 0.313,0.156 10 false *1 0.344,0.25 0.573,0.417 0.229,0.167 10 true 90° 1.188,1.76 1.438,1.969 0.25,0.208 10 false *a
*1 Crankshaft Timing Gear Key
*a Turn


Turn the crankshaft and set the crankshaft timing gear key to the left horizontal position.

NOTICE:

Having the crankshaft at the wrong angle can cause the piston head and valve head to come into contact with each other when the camshaft is installed, causing damage. Always set the crankshaft to the correct angle.



c.
A326647

Set the No. 3 camshaft sub-assembly and No. 4 camshaft sub-assembly as shown in the illustration.


d.
A326648

Check the numbers on the camshaft bearing caps and the installation direction before temporarily placing each cap.


e.

Apply a light coat of engine oil to the threads and under the heads of the bolts.


f.
A326620C01
0.125,0.552 0.271,0.729 0.146,0.177 10 true 6 0.146,1.01 0.281,1.188 0.135,0.177 10 true 5 0.125,1.26 0.292,1.438 0.167,0.177 10 true 7 0.115,1.656 0.271,1.854 0.156,0.198 10 true 8 1.406,0.458 1.615,0.635 0.208,0.177 10 true 2 2.135,0.469 2.344,0.646 0.208,0.177 10 true 10 2.885,0.458 3.094,0.635 0.208,0.177 10 true 14 0.896,1.271 1.031,1.427 0.135,0.156 10 true 1 1.354,0.979 1.563,1.125 0.208,0.146 10 true 3 1.615,1.25 1.781,1.427 0.167,0.177 10 true 9 2.115,1.104 2.313,1.281 0.198,0.177 10 true 11 2.365,1.26 2.573,1.427 0.208,0.167 10 true 13 2.875,1.177 3.115,1.354 0.24,0.177 10 true 15 0.938,1.948 1.146,2.094 0.208,0.146 10 true 4 1.646,1.969 1.854,2.115 0.208,0.146 10 true 12 2.417,1.958 2.625,2.104 0.208,0.146 10 true 16
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 16 bolts in several steps in the order shown in the illustration.

Torque:
for bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 39 mm (1.54 in.)
Bolt B 50 mm (1.97 in.)



g.

Remove the crankshaft pulley set bolt.


Hide 11821 13.INSTALL NO. 2 CAMSHAFT BEARING

a.
A326642

Install the No. 2 camshaft bearing to the cylinder head sub-assembly.

NOTICE:

Clean the backside of the No. 2 camshaft bearing and the contact surface of the cylinder head sub-assembly and prevent oil from adhering to them.



Hide 11811 14.INSTALL NO. 1 CAMSHAFT BEARING

a.
A326641C01
0.448,0.906 0.76,1.063 0.313,0.156 10 false *a
*a Claw


Align the claw of the No. 1 camshaft bearing with the groove of the camshaft bearing cap and push in the No. 1 camshaft bearing.

NOTICE:
·

Install the No. 1 camshaft bearing while aligning it with the oil hole in the camshaft bearing cap.

·

Clean the backside of the No. 1 camshaft bearing and the contact surface of the camshaft bearing cap and prevent oil from adhering to them.




Hide 13512 15.INSTALL NO. 2 CAMSHAFT

a.

Apply new engine oil to the thrust portion and journals of the No. 2 camshaft.


b.

Install the No. 2 camshaft to the cylinder head sub-assembly.


Hide 13511 16.INSTALL CAMSHAFT

a.

Apply new engine oil to the thrust portion and journals of the camshaft.


b.

Install the camshaft to the cylinder head sub-assembly.


Hide 17.INSTALL CAMSHAFT BEARING CAP (for Bank 1)

NOTICE:

As the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. If the camshaft is not kept level, the portion of the cylinder head which receives the shaft thrust may crack or be damaged, causing the camshaft to seize or break. To avoid this, make sure the following steps are carried out.


a.

Temporarily install the crankshaft pulley set bolt.


b.
A326643C02
0.448,1.333 0.615,1.333 0.615,1.333 0.615,0.667 true 0.271,1.25 0.583,1.406 0.313,0.156 10 false *1 0.333,0.25 0.552,0.417 0.219,0.167 10 true 90° 1.188,1.76 1.458,1.948 0.271,0.188 10 false *a
*1 Crankshaft Timing Gear Key
*a Turn


Turn the crankshaft and set the crankshaft timing gear key to the left horizontal position.

NOTICE:

Having the crankshaft at the wrong angle can cause the piston head and valve head to come into contact with each other when the camshaft is installed, causing damage. Always set the crankshaft to the correct angle.



c.
A326644

Set the camshaft and No. 2 camshaft as shown in the illustration.


d.
A326645

Check the numbers on the camshaft bearing caps and the installation direction before temporarily placing each cap.


e.

Apply a light coat of engine oil to the threads and under the heads of the bolts.


f.
A326619C01
0.51,0.469 0.708,0.635 0.198,0.167 10 true 14 1.417,0.281 1.656,0.458 0.24,0.177 10 true 10 2.125,0.271 2.323,0.438 0.198,0.167 10 true 2 3.094,0.396 3.292,0.563 0.198,0.167 10 true 6 0.49,1.104 0.677,1.271 0.188,0.167 10 true 15 1.073,1.229 1.26,1.385 0.188,0.156 10 true 13 1.292,0.969 1.479,1.146 0.188,0.177 10 true 11 1.823,1.229 1.969,1.396 0.146,0.167 10 true 9 2.063,0.958 2.26,1.115 0.198,0.156 10 true 3 2.583,1.24 2.76,1.438 0.177,0.198 10 true 1 3.188,1 3.365,1.198 0.177,0.198 10 true 5 3.188,1.26 3.365,1.458 0.177,0.198 10 true 7 1.073,1.958 1.313,2.156 0.24,0.198 10 true 16 1.844,1.958 2.021,2.156 0.177,0.198 10 true 12 2.531,1.948 2.708,2.146 0.177,0.198 10 true 4 3.083,1.958 3.26,2.156 0.177,0.198 10 true 8
V100135

Bolt A
V100136

Bolt B


Install and uniformly tighten the 16 bolts in several steps in the order shown in the illustration.

Torque:
for bolt A : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt B : 24 N*m (245 kgf*cm, 18 ft.*lbf)

Standard Bolt Length:
Item Specified Condition
Bolt A 39 mm (1.54 in.)
Bolt B 50 mm (1.97 in.)



g.
A326646C02
1.833,0.51 2.042,0.688 0.208,0.177 10 true *a 1.333,0.927 1.542,1.104 0.208,0.177 10 true *a 1.25,1.458 1.479,1.646 0.229,0.188 10 true 90° 1.979,1.073 2.208,1.26 0.229,0.188 10 true 90°
*a Turn


Turn the camshafts clockwise until the camshaft knock pin is at a position 90° from the cylinder head sub-assembly.


h.

Remove the crankshaft pulley set bolt.


Hide 13560A 18.INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

a.
A326555C01
2.573,1.115 2.885,1.271 0.313,0.156 10 false *a
*a Push


While pushing in the No. 3 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 3 chain tensioner assembly in place.


b.

Install the No. 3 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 19.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

a.
A326678C01
0.979,0.583 0.979,0.24 0.979,0.24 1.135,0.24 true 2.365,0.594 2.365,0.167 2.365,0.167 2.521,0.167 true 0.979,0.677 0.5,1.5 0.5,1.5 0.333,1.5 true 2.354,0.688 1.917,1.833 1.917,1.833 1.75,1.833 true 1.917,1.833 2.417,0.688 true 1.177,0.167 1.49,0.323 0.313,0.156 10 false *a 0.167,1.406 0.479,1.563 0.313,0.156 10 false *b 2.583,0.073 2.896,0.229 0.313,0.156 10 false *a 1.583,1.74 1.896,1.896 0.313,0.156 10 false *b
*a Mark Link (Yellow)
*b Timing Mark


Align the mark links (yellow) of the No. 2 chain sub-assembly with the timing marks of the camshaft timing gear assembly and camshaft timing sprocket.


b.
A218540C01
1.563,0.49 2.354,0.188 2.354,0.188 2.042,1.031 true 1.417,1.344 0.583,1.729 true 0.844,0.813 0.583,1.729 0.583,1.729 0.896,0.875 true 2.396,0.104 2.677,0.302 0.281,0.198 10 true *a 0.521,1.74 0.74,1.979 0.219,0.24 10 false *a
*a Timing Mark


Align the timing marks on the camshaft timing gear assembly and camshaft timing sprocket with the timing marks on the camshaft bearing caps, and install the camshaft timing gear assembly and camshaft timing sprocket together with the No. 2 chain sub-assembly.


c.

Temporarily install the camshaft timing gear assembly and camshaft timing sprocket with the 2 bolts.

NOTICE:

Do not push the camshaft timing gear assembly onto the No. 3 camshaft sub-assembly forcibly when installing it.



d.
A326679

Hold the hexagonal portion of the No. 4 camshaft sub-assembly with a wrench and tighten the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Remove the pin from the No. 3 chain tensioner assembly.


Hide 13550 20.INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A326569C01
2.542,1.146 2.854,1.302 0.313,0.156 10 false *a
*a Push


While pushing in the No. 2 chain tensioner assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the No. 2 chain tensioner assembly in place.


b.

Install the No. 2 chain tensioner assembly with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 21.INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

a.
A326649C01
1,0.583 1,0.167 1,0.167 1.167,0.167 true 2.375,0.583 2.375,0.167 2.375,0.167 2.542,0.167 true 1,0.698 1.167,0.948 1.167,0.948 1.333,0.948 true 2.385,0.688 2.552,0.938 2.552,0.938 2.719,0.938 true 1.188,0.094 1.5,0.25 0.313,0.156 10 false *a 1.385,0.875 1.583,1.083 0.198,0.208 10 true *b 2.583,0.094 2.896,0.25 0.313,0.156 10 false *a 2.76,0.865 2.958,1.073 0.198,0.208 10 true *b
*a Mark Link (Yellow)
*b Timing Mark


Align the mark links (yellow) of the No. 2 chain sub-assembly with the timing marks of the camshaft timing gear assembly and camshaft timing sprocket.


b.
A218539C01
1.031,0.667 1.302,0.667 1.302,0.667 1.385,1.104 false 2.458,0.135 2.271,0.135 2.271,0.135 1.958,0.594 false 1.958,1.521 1.292,0.667 false 2.708,1.042 2.271,0.146 false 0.771,0.573 1,0.74 0.229,0.167 10 true *a 2.5,0.063 2.729,0.229 0.229,0.167 10 true *a
*a Timing Mark


Align the timing marks on the camshaft timing gear assembly and camshaft timing sprocket with the timing marks on the camshaft bearing caps, and install the camshaft timing gear assembly and camshaft timing sprocket together with the No. 2 chain sub-assembly.


c.

Temporarily install the camshaft timing gear assembly and camshaft timing sprocket with the 2 bolts.

NOTICE:

Do not push the camshaft timing gear assembly onto the camshaft forcibly when installing it.



d.
A326677

Hold the hexagonal portion of the No. 2 camshaft with a wrench and tighten the 2 bolts.

Torque:
100 N*m (1020 kgf*cm, 74 ft.*lbf)


e.

Remove the pin from the No. 2 chain tensioner assembly.


Hide 13561 22.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 13521 23.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A326680C01
1.323,0.281 1.635,0.479 0.313,0.198 10 false *a
*a Inward


Align the crankshaft timing gear key with the groove of the crankshaft timing sprocket and install the crankshaft timing sprocket as shown in the illustration.


Hide 13559 24.INSTALL CHAIN TENSIONER SLIPPER

Hide 13540 25.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A326575C02
2.677,1.896 2.677,1.427 true 1.042,1.156 1.302,0.656 1.302,0.656 1.479,0.656 true 2.594,1.927 2.906,2.083 0.313,0.156 10 false *a 2.031,2 2.344,2.156 0.313,0.156 10 false *b 1.542,0.594 1.854,0.75 0.313,0.156 10 false *a
*a Stopper Plate
*b Push


While turning the stopper plate of the No. 1 chain tensioner assembly clockwise, push in the plunger of the No. 1 chain tensioner assembly as shown in the illustration.


b.

While turning the stopper plate of the No. 1 chain tensioner assembly counterclockwise, insert a bar with a diameter of 3.5 mm (0.138 in.) into the holes in the stopper plate and No. 1 chain tensioner assembly to fix the stopper plate in place.


c.

Install the No. 1 chain tensioner assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 26.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Set the No. 1 cylinder to TDC/compression.

i.

Align the timing marks of the camshaft timing gear assemblies and camshaft timing sprockets with the timing marks of the camshaft bearing caps.

A297273C04
1.583,1.417 1.104,0.833 true 1.583,1.417 1.135,0.594 true 1.583,1.417 2.385,0.604 true 1.583,1.417 2.479,0.906 true 5.583,1.417 5.969,0.885 true 5.583,1.417 5.917,0.552 true 5.583,1.417 4.76,0.958 true 5.583,1.417 4.792,0.604 true 0.417,0.083 0.729,0.281 0.313,0.198 10 false *A 4,0.083 4.313,0.281 0.313,0.198 10 false *B 1.49,1.448 1.719,1.646 0.229,0.198 10 true *a 5.51,1.448 5.74,1.646 0.229,0.198 10 true *a
*A for Bank 1 *B for Bank 2
*a Timing Mark - -



ii.
A326681C01
1.344,0.51 1.458,0.281 1.458,0.281 1.646,0.281 false 1.667,1.052 1.781,0.823 1.781,0.823 1.969,0.823 true 1.677,0.198 1.99,0.396 0.313,0.198 10 true *a 2.021,0.74 2.333,0.938 0.313,0.198 10 true *b
*a Timing Line
*b Crankshaft Timing Gear Key


Temporarily install the crankshaft pulley set bolt and turn the crankshaft to align the crankshaft timing gear key with the timing line of the cylinder block sub-assembly.



Hide 13506 27.INSTALL CHAIN SUB-ASSEMBLY

a.
A326682C01
1.448,1.115 1.75,1.115 true 0.854,1.135 1.333,1.135 true 0.688,1.052 0.896,1.24 0.208,0.188 10 true *a 1.781,1.031 1.99,1.24 0.208,0.208 10 true *b
*a Mark Link (Yellow)
*b Timing Mark


Align the mark link (yellow) of the chain sub-assembly with the timing mark of the crankshaft timing sprocket.


b.
A326683C01
1.729,0.438 1.469,0.135 1.469,0.135 1.302,0.135 true 2.917,1.135 2.917,0.646 2.917,0.646 3.083,0.646 true 1.719,0.604 1.458,0.885 1.458,0.885 1.292,0.885 true 2.99,1.313 2.99,1.813 2.99,1.813 3.156,1.813 true 3,1.833 2.833,1.333 false 1.125,0.042 1.438,0.198 0.313,0.156 10 false *a 3.198,1.729 3.365,1.969 0.167,0.24 10 false *b 3.125,0.552 3.333,0.75 0.208,0.198 10 true *a 1.063,0.781 1.271,1 0.208,0.219 10 true *b
*a Mark Link (Orange)
*b Timing Mark


Align the mark links (orange) of the chain sub-assembly with the timing marks of the camshaft timing gear assemblies and install the chain sub-assembly.


Hide 13562 28.INSTALL NO. 2 CHAIN VIBRATION DAMPER

a.

Install the 2 No. 2 chain vibration dampers.


Hide 13530 29.INSTALL IDLE SPROCKET ASSEMBLY

a.

Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.

HINT:

Check for foreign matter on the No. 1 idle gear shaft and No. 2 idle gear shaft.



b.
A326684C01
0.604,1.656 0.604,0.698 0.604,0.698 0.458,0.698 true 2.938,0.219 3.25,0.375 0.313,0.156 10 false *a 0.302,0.604 0.615,0.76 0.313,0.156 10 false *b
*a Forward
*b Knock Pin


Temporarily install the No. 1 idle gear shaft and idle sprocket assembly together with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block sub-assembly.

NOTICE:

Make sure the idle sprocket assembly is installed facing the proper direction.



c.

Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

Torque:
60 N*m (612 kgf*cm, 44 ft.*lbf)


d.

Remove the bar from the No. 1 chain tensioner assembly.


Hide 16100 30.INSTALL ENGINE WATER PUMP ASSEMBLY

a.

Install a new gasket and the engine water pump assembly with the 8 bolts.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


Hide 11302 31.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11324 33.INSTALL TIMING CHAIN COVER PLATE

Hide 11381A 34.INSTALL REAR CRANKSHAFT OIL SEAL

a.
A326639N01
1.75,1.458 2.208,1.458 true 2.25,1.365 2.708,1.563 0.458,0.198 10 false SST

Using SST and a hammer, tap in a new rear crankshaft oil seal until its surface is flush with the engine rear oil seal retainer edge.

SST
09223-78010  


b.

Apply MP grease to the lip of the rear crankshaft oil seal.


Hide 11381 35.INSTALL ENGINE REAR OIL SEAL RETAINER

a.

Clean and degrease the contact surfaces of the engine rear oil seal retainer and cylinder block.


b.
A326640C01
1.813,0.458 2.01,0.229 2.01,0.229 2.198,0.229 true 2.25,0.167 2.563,0.323 0.313,0.156 10 false *a
*a Seal Packing Application Area


Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


NOTICE:

Parts must be assembled within 3 minutes of application. Otherwise the seal packing must be removed and reapplied.



c.

Install the engine rear oil seal retainer with the 5 bolts and 2 nuts.

Torque:
for nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12101 36.INSTALL OIL PAN SUB-ASSEMBLY

Hide 15104 37.INSTALL OIL STRAINER SUB-ASSEMBLY

Hide 12102A 38.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12101A 39.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 13471 40.INSTALL CRANKSHAFT PULLEY

Hide 41.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11202 44.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

Hide 12204 45.INSTALL PCV VALVE SUB-ASSEMBLY

Hide 11201 46.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12185 48.INSTALL OIL FILLER CAP HOUSING

a.
A158574C01
1.073,0.188 1.229,0.188 1.229,0.188 1.438,1.365 true 0.875,0.083 1.167,0.25 0.292,0.167 10 false *1
*1 Gasket


Install a new gasket and the oil filler cap housing with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12108 49.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the gasket to the oil filler cap sub-assembly.


b.

Install the oil filler cap sub-assembly.


Hide 16356 50.INSTALL REAR WATER BY-PASS JOINT

a.
A302363C01
1.667,0.792 2.052,0.792 false 1.521,1.625 0.615,1.844 0.615,1.844 0.49,1.51 true 2.115,0.688 2.427,0.885 0.313,0.198 10 true *1 0.51,1.865 0.823,2.063 0.313,0.198 10 false *2
*1 O-Ring
*2 Gasket


Apply soapy water to a new O-ring and install it to the No. 1 water outlet pipe. Then install 2 new gaskets to the water ports LH and RH.


b.

Install the rear water by-pass joint with the 2 bolts and 4 nuts.

Torque:
for bolt : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for nut : 9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 16323 51.INSTALL WATER INLET ASSEMBLY

Hide 15609 52.INSTALL OIL FILTER BRACKET SUB-ASSEMBLY

Hide 15710 53.INSTALL OIL COOLER ASSEMBLY

Hide 15601 54.INSTALL OIL FILTER SUB-ASSEMBLY

Hide 15678A 55.INSTALL OIL CONTROL VALVE FILTER

a.
A326690C01
1.177,0.75 1.177,0.406 1.177,0.406 1.333,0.406 false 2.031,1.052 2.031,0.708 2.031,0.708 2.188,0.708 false 2.25,0.625 2.563,0.823 0.313,0.198 10 false *1 1.375,0.323 1.688,0.521 0.313,0.198 10 false *a
*1 New Gasket
*a Mesh Part
V100135

Adhesive


Make sure that the mesh is free from damage and foreign matter.


b.

Install 2 new gaskets to 2 new oil control valve filters.


c.

Install the 2 oil control filters into the 2 new unions.


d.

Apply adhesive to 2 or 3 threads of the unions.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



e.

Install the 2 unions to the cylinder head sub-assembly and cylinder head LH.

Torque:
62 N*m (632 kgf*cm, 46 ft.*lbf)


Hide 15340 56.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 2)

Hide 15330B 57.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (for Bank 1)

Hide 11401G 58.INSTALL CRANKSHAFT POSITION SENSOR

Hide 11415 61.INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.

Remove any oil from the threads of the cylinder block water drain cock sub-assembly.


b.

Apply adhesive to 2 or 3 threads at the end of the cylinder block water drain cock sub-assembly.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.
A302377N02
0.448,1.802 0.698,2.01 0.25,0.208 10 true 75° 0.948,1.792 1.188,1.969 0.24,0.177 10 true 45°

Install the cylinder block water drain cock sub-assembly.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Install the cylinder block water drain cock sub-assembly within 3 minutes after applying adhesive.

·

Do not expose the cylinder block water drain cock sub-assembly to engine coolant within 1 hour after installation.




d.

Rotate the cylinder block water drain cock sub-assembly clockwise as shown in the illustration.

NOTICE:
·

Do not rotate the cylinder block water drain cock sub-assembly by more than 1 revolution (360°) after tightening the cylinder block water drain cock sub-assembly to the specified torque.

·

Do not loosen the cylinder block water drain cock sub-assembly after setting it correctly.




e.

Install the cylinder block water drain cock plug to the cylinder block water drain cock sub-assembly.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 89422 62.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 83530 63.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY