Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR
RM33K0E _55 Steering _043540 STEERING GEAR / LINKAGE _0227302 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.ADJUST TIE ROD END SUB-ASSEMBLY

a.
C323285E01
1.229,1.396 1.385,1.594 0.156,0.198 10 false A

Adjust the tie rod end sub-assembly LH and RH so that distance A is within the specified ranges.

Standard Length (A):

17 mm (0.6693 in.) or less


CAUTION:

Make sure to tighten the nut in the alignment adjustment procedure.


NOTICE:

Make sure that the boots are not twisted.


HINT:
·

The values listed above are reference values.

·

The toe-in is adjusted in another step.




Hide 2.INSTALL POWER STEERING LINK ASSEMBLY

a.

Install the power steering link assembly with the 2 bolts, 2 washers and 2 nuts.

Torque:
130 N*m (1326 kgf*cm, 96 ft.*lbf)


b.
C330549C01
1.531,0.063 1.844,0.219 0.313,0.156 10 true *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the steering gear outlet return tube.

Torque:
Specified tightening torque : 25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)




c.

Install the hose with the clip.


d.

Install the pressure feed tube assembly bracket to the power steering link assembly with the bolt.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


e.
C330548C01
1.531,0.156 1.844,0.313 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, tighten the flare nut and connect the pressure feed tube assembly.

Torque:
Specified tightening torque : 25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 30 mm (1.1811 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 21.4 N*m (218 kgf*cm, 16 ft.*lbf)




Hide 41110F 3.INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY

Hide 45203 4.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

a.

Align the matchmarks on the No. 2 steering intermediate shaft sub-assembly and power steering link assembly.


b.

Install the bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45219 5.CONNECT STEERING SLIDING YOKE

a.
C330544C01
0.656,0.927 1.094,0.99 1.094,0.99 0.76,0.802 true 1.135,0.906 1.448,1.104 0.313,0.198 10 false *a
*a Matchmark
V113147

Install in this Direction


Align the matchmarks on the steering sliding yoke and No. 2 steering intermediate shaft, and connect the steering sliding yoke to the No. 2 steering intermediate shaft sub-assembly.


b.
C330543N01
2.146,0.75 2.302,0.948 0.156,0.198 10 true A 1.885,1.094 2.042,1.292 0.156,0.198 10 true B

Install the bolt labeled B.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


c.

Tighten the bolt labeled A.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


Hide 45047 6.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Connect the tie rod end sub-assembly LH to the front axle hub assembly with a new nut.

Torque:
91 N*m (928 kgf*cm, 67 ft.*lbf)


b.

Install a new cotter pin.

NOTICE:

If the holes for the cotter pin are not aligned, tighten the nut an additional 60°.



Hide 45046 7.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51442 8.INSTALL NO. 2 ENGINE UNDER COVER

Hide 51410 9.INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY

Hide 10.INSTALL FRONT WHEELS

Hide 11.ADD POWER STEERING FLUID

Hide 13.CHECK FOR POWER STEERING FLUID LEAK