Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS
RM33K0E _59 Vehicle Exterior _043558 WINDOW / GLASS _0229937 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the windshield glass removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Disconnect cable from negative battery terminal w/ Power Back Door System:
Reset back door close position
Power door lock control system (Click here)

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedures listed below are for LHD vehicles.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 85292B 3.REMOVE FRONT WIPER ARM HEAD CAP

Hide 4.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 5.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53886G 6.REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY LH

Hide 53885G 7.REMOVE FENDER APRON MUDGUARD SEAL SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 53867H 8.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 9.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure described for the LH side.


Hide 55781E 10.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 74603 11.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

Hide 62212 12.REMOVE FRONT PILLAR GARNISH LH

Hide 62211 13.REMOVE FRONT PILLAR GARNISH RH

Hide 87810 14.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 81260A 15.REMOVE MAP LIGHT ASSEMBLY

Hide 81240 16.REMOVE NO. 1 ROOM LIGHT ASSEMBLY

Hide 74325 17.REMOVE VISOR BRACKET COVER LH

Hide 74325 18.REMOVE VISOR BRACKET COVER RH

Hide 74320 19.REMOVE VISOR ASSEMBLY LH

Hide 74310 20.REMOVE VISOR ASSEMBLY RH

Hide 74610A 22.REMOVE ASSIST GRIP SUB-ASSEMBLY

Hide 63310 23.REMOVE ROOF HEADLINING ASSEMBLY

HINT:

Remove a sufficient amount of the front portion of the roof headlining assembly so that windshield glass removal and installation procedures can be performed.


a.

Partially remove the roof headlining assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 56111 24.REMOVE WINDSHIELD GLASS

NOTICE:
·

The windshield glass may fall while performing this procedure. Therefore, use suction cups to hold the windshield glass from the outside of the vehicle.

·

Be careful not to damage the windshield glass when cutting as the windshield glass stopper and No. 2 windshield glass stopper are installed to the windshield glass.



a.
B437151C01
0,0 0,0 false
V100155

Protective Tape


Put protective tape on the body surface around the windshield glass.


b.
B405928C01
1.76,0.469 2.031,0.208 2.031,0.208 2.229,0.208 false 2.302,0.125 2.615,0.323 0.313,0.198 10 false *a
*a Matchmarks


When reusing the windshield glass:

Place adhesive tape on the windshield glass and body panel and use a pen to place matchmarks for installation.


c.

Install the suction cups to the windshield glass.


d.
B405967C01
2.125,0.76 2.844,0.323 true 1.552,0.281 1.979,0.188 true 2.688,1.531 2.979,1.573 false 0.771,0.708 0.365,0.635 true 2.052,0.125 2.365,0.281 0.313,0.156 10 true *1 2.885,0.219 3.198,0.375 0.313,0.156 10 false *2 0.167,0.573 0.479,0.729 0.313,0.156 10 true *3 3.063,1.521 3.375,1.719 0.313,0.198 10 false *1
*1 Handles
*2 Plastic Sheet
*3 Protective Tape


Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.

NOTICE:
·

When separating the glass from the vehicle, be careful not to damage the vehicle paint or interior/exterior ornaments.

·

To prevent the instrument panel from being scratched when removing the glass, place a plastic sheet between the piano wire and instrument panel.




e.
B437133C01
1.052,0.563 2.656,0.198 2.656,0.198 2.302,0.604 true 0.781,1.813 1.354,1.865 1.354,1.865 1.198,1.583 true 2.698,0.094 3.01,0.25 0.313,0.156 10 true *1 1.438,1.854 1.75,2.01 0.313,0.156 10 false *2
*1 Stopper
*2 Piano Wire


Insert a piano wire (approximately 0.6 mm) at the locations shown in the illustration.


f.

Pull on the ends of the piano wire alternately and leave the stoppers when cutting through the adhesive.

NOTICE:
·

Do not forcefully brush the piano wire against the windshield glass.


·

Be careful as the piano wire will break if it crosses itself.




g.

Using suction cups, detach the 2 windshield glass stoppers to remove the windshield glass.

B437134C01
1.49,0.417 1.708,0.552 false 1.75,0.979 2.063,0.979 false 5.177,0.563 4.938,0.406 false 4.938,0.844 4.823,1.031 4.823,1.031 4.625,1.031 false 5.104,0.885 5.188,1.083 5.188,1.083 5.583,1.083 false 0.792,0.198 1.104,0.354 0.313,0.156 10 false *A 4.25,0.198 4.563,0.354 0.313,0.156 10 false *B 5.625,0.979 5.938,1.135 0.313,0.156 10 false *1 4.458,0.948 4.771,1.104 0.313,0.156 10 false *2 1.313,0.292 1.625,0.448 0.313,0.156 10 false *3 2.146,0.906 2.479,1.073 0.333,0.167 10 false *1 4.771,0.333 5.083,0.531 0.313,0.198 10 false *3
*A for 1-piece Type *B for 2-piece Type
*1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper
*3 Windshield Glass - -


NOTICE:
·

The windshield glass stopper and No. 2 windshield glass stoppers are installed on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.


·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.