Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
A bolt without a torque specification is shown in the standard bolt chart.
Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS
62704A
1.INSTALL REAR QUARTER WINDOW GLASS RETAINER SUB-ASSEMBLY LH
Attach the clip.
Install the rear quarter window glass retainer sub-assembly LH with the screw.
62720A
2.CLEAN QUARTER WINDOW ASSEMBLY LH
Clean the outer edges of a new quarter window assembly LH with non-residue solvent.
62763J
3.INSTALL UPPER QUARTER WINDOW GLASS RETAINER
Apply Primer G to the upper quarter window glass retainer installation area on the quarter window glass LH.
Do not apply too much Primer G.
Remove the peeling paper and install a new upper quarter window glass retainer.
| *1 | Upper Quarter Window Glass Retainer |
| *a | Back Side of Quarter Window Glass LH |
| *b | Ceramic Notch |
Install the upper quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.
Install the upper quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).
62761H
4.INSTALL FRONT QUARTER WINDOW GLASS RETAINER
Apply Primer G to the front quarter window glass retainer installation area on the quarter window glass LH.
Do not apply too much Primer G.
Remove the peeling paper and install a new front quarter window glass retainer.
| *1 | Front Quarter Window Glass Retainer |
| *a | Back Side of Quarter Window Glass LH |
| *b | Ceramic Notch |
Install the front quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.
Install the front quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).
69998B
5.INSTALL NO. 2 QUARTER WINDOW GUIDE PIECE PIN
Apply Primer G to the No. 2 quarter window guide piece pin installation area on the quarter window glass LH.
Do not apply too much Primer G.
Remove the peeling paper and install a new No. 2 quarter window guide piece pin.
| *1 | No. 2 Quarter Window Guide Piece Pin |
| *a | Back Side of Quarter Window Glass LH |
| *b | Ceramic Notch |
Install the No. 2 quarter window guide piece pin to the quarter window glass LH in the location shown in the illustration.
Install the No. 2 quarter window guide piece pin after Primer G has been allowed to dry (approximately 3 minuts).
62767B
6.INSTALL REAR QUARTER WINDOW GLASS RETAINER
Apply Primer G to the rear quarter window glass retainer installation area on the quarter window glass LH.
Do not apply too much Primer G.
Remove the peeling paper and install a new rear quarter window glass retainer.
| *1 | Rear Quarter Window Glass Retainer |
| *a | Back Side of Quarter Window Glass LH |
| *b | Ceramic Notch |
Install the rear quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.
Install the rear quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).
62765H
7.INSTALL LOWER QUARTER WINDOW GLASS RETAINER
Apply Primer G to the lower quarter window glass retainer installation area on the quarter window glass LH.
Do not apply too much Primer G.
Remove the peeling paper and install a new lower quarter window glass retainer.
| *1 | Lower Quarter Window Glass Retainer |
| *a | Back Side of Quarter Window Glass LH |
| *b | Ceramic Notch |
Install the lower quarter window glass retainer to the quarter window glass LH in the location shown in the illustration.
Install the lower quarter window glass retainer after Primer G has been allowed to dry (approximately 3 minuts).
56117C
8.INSTALL REAR SIDE WINDOW GLASS ADHESIVE DAM
Apply Primer G to the rear side window glass adhesive dam installation area of the quarter window glass.
Do not apply too much Primer G.
Remove the peeling paper and install a new rear side window glass adhesive dam.
Install the rear side window glass adhesive dam to the quarter window glass in the location shown in the illustration.
| *a | Back Side of Quarter Window Glass LH | *b | Rear Side Window Glass Adhesive Dam Center Line |
| *c | Ceramic Notch | - | - |
Install the rear side window glass adhesive dam after Primer G has been allowed to dry (approximately 3 minuts).
| Area | Measurement |
|---|---|
| a | 3.1 mm (0.122 in.) |
9.INSTALL QUARTER WINDOW MOULDING LH
| *1 | Quarter Window Moulding LH |
| *2 | Quarter Window Glass LH |
|
Primer G |
Apply Primer G to the quarter window moulding LH installation area of the quarter window glass LH and new quarter window moulding LH.
Do not apply too much Primer G.
| Area | Specified Condition |
|---|---|
| a | 11.8 mm (0.465 in.) |
|
Adhesive |
Apply adhesive to the quarter window moulding LH.
Cut off the tip of a cartridge nozzle.
Load a sealer gun with the cartridge.
Apply adhesive to the quarter window moulding LH as shown in the illustration.
Apply the adhesive after Primer G has been allowed to dry (approximately 3 minuts).
Remove the peeling paper and install the quarter window moulding LH.
Install the quarter window moulding LH as shown in the illustration.
| *a | Back Side of Quarter Window Glass LH | *b | R End |
Apply non-residue solvent to a clean cloth and wipe off any excess or protruding adhesive.
62785A
10.INSTALL QUARTER WINDOW GLASS SPACER
Apply Primer G to the quarter window glass spacer installation area on the quarter window glass LH.
Do not apply too much Primer G.
Remove the peeling paper and install a new quarter window glass spacer.
| *1 | Quarter Window Glass Spacer |
| *a | Back Side of Quarter Window Glass LH |
| *b | Ceramic Notch |
Install the quarter window glass spacer to the quarter window glass LH in the location shown in the illustration.
Install the quarter window glass spacer after Primer G has been allowed to dry (approximately 3 minuts).
62775C
11.INSTALL QUARTER WINDOW CLIP
Apply Primer G to the quarter window clip installation area of the quarter window glass LH.
Do not apply too much Primer G.
| *a | Back Side of Quarter Window Glass LH | *b | Ceramic Line |
|
Primer G | - | - |
Apply adhesive to the location shown in the illustration and install the 8 quarter window clips (for Type A) and quarter window clip (for Type B) to the quarter window glass LH in the location shown in the illustration.
| *A | for Type A | *B | for Type B |
| *1 | Quarter Window Clip | - | - |
| *a | Back Side of Quarter Window Glass LH | *b | Ceramic Line |
|
Adhesive | - | - |
Using a scraper, remove any excess adhesive or apply as necessary.
Apply adhesive up to the edge of the windshield glass.
75646
12.INSTALL REAR OUTSIDE QUARTER WINDOW MOULDING LH
After the adhesive hardens, attach the claw to install the rear outside quarter window moulding LH as shown in the illustration.
| *1 | Quarter Window Clip (for Type B) | *2 | Rear Outside Quarter Window Moulding LH |
|
Install in this Direction |
|
Install in this Order |
62720A
13.INSTALL QUARTER WINDOW ASSEMBLY LH
| *1 | Vehicle Body |
|
Adhesive |
Clean and shape the contact surface of the vehicle body.
On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
Leave as much adhesive on the vehicle body as possible.
Be careful not to damage the vehicle body.
Clean the contact surface of the vehicle body with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.
Clean the outer edges of the quarter window assembly LH with non-residue solvent.
Quarter window assembly LH preliminary installation procedures.
Install the suction cups to a new quarter window assembly LH.
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Do not apply too much Primer M.
Do not apply Primer M to the adhesive.
Be careful when applying primer to the panel joints and spot welds.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Apply Primer G to the quarter window glass assembly LH in the locations shown in the illustration.
| *a | Back Side of Quarter Window Assembly LH | *b | Adhesive Application Center Line |
|
Primer G Application Area | - | - |
| Area | Measurement |
|---|---|
| a | 7.0 mm (0.276 in.) |
| b | 20.0 mm (0.787 in.) |
If primer is applied to an area that is not specified, wipe off the primer with non-residue solvent before it dries.
Allow the primer to dry for 3 minutes or more.
Throw away any leftover primer.
Do not apply too much primer.
Apply adhesive to the quarter window assembly LH.
Toyota Genuine Windshield Glass Adhesive or equivalent
| *1 | Sealer Gun |
| *2 | Nozzle |
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Specified Condition |
|---|---|
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
After cutting off the tip, use all adhesive within the time written in the table below.
| Temperature | Usage Time Frame |
|---|---|
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply a bead of adhesive to the quarter window assembly LH in the locations shown in the illustration.
| *a | Back Side of Quarter Window Glass Assembly LH | *b | Adhesive Application Center Line |
|
Adhesive | - | - |
| Area | Measurement |
|---|---|
| a | 8.0 mm (0.315 in.) |
| b | 12.0 mm (0.472 in.) |
Apply the adhesive after Primer G has been allowed to dry (approximately 3 minuts).
Using suction cups, attach the 4 clips to install the quarter window assembly LH.
Install the quarter window assembly LH after Primer M on the vehicle body has been allowed to dry (approximately 3 minuts).
From the interior, check that the quarter window assembly LH is securely attached.
Lightly press the quarter window assembly LH from outside the vehicle so that it is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.
Using a scraper, remove any excess adhesive or apply as necessary.
Remove any excess adhesive before it hardens.
Hold the quarter window assembly LH in place securely with protective tape or equivalent until the adhesive hardens.
Follow the instructions for each adhesive manufacturer or the corresponding owner's manual for the minimum amount of time necessary prior to driving the vehicle.
14.CHECK FOR QUARTER WINDOW ASSEMBLY LH
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
Remove any protective tape.
62792V
15.INSTALL UPPER QUARTER WINDOW MOULDING LH
62472D
16.INSTALL UPPER REAR PILLAR GARNISH LH
73178B
17.INSTALL SEAT BELT ANCHOR COVER CAP
62639A
18.INSTALL QUARTER PILLAR GARNISH LH
73178B
19.INSTALL SEAT BELT ANCHOR COVER CAP
62512
20.INSTALL QUARTER INSIDE TRIM BOARD LH
73233B
21.INSTALL REAR NO. 2 SEAT OUTER LAP BELT ANCHOR COVER
73233A
22.INSTALL REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
67935
23.INSTALL BACK DOOR SCUFF PLATE
67918E
24.INSTALL REAR DOOR SCUFF PLATE LH
25.INSTALL REAR NO. 2 SEAT ASSEMBLY
26.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION